Avient Corporation ve bağlı kuruluşları ve iştirakleri ("Avient'') dünya standartlarında sürdürülebilir bir kuruluş olmayı taahhüt etmektedir.

www.avient.com Copyright © 2020, Avient Corporation.

FASTENER SELECTION Copyright © 2022, Avient Corporation.

PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Increase shot size • Increase injection rate • Increase packing pressure Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature TROUBLESHOOTING RECOMMENDATIONS www.avient.com Copyright © 2020, Avient Corporation.

Vents should be placed at the intersection of each 90° bend in the runner system off of the cold slug well and vented to atmosphere Black Specks Contamination • Purge barrel with general purpose PP • Verify correct nozzle is being used • Pull screw for cleaning Degraded/overheated material • Decrease melt temperature • Decrease injection speed • Use appropriately sized barrel Brittleness Degraded/overheated material • Decrease melt temperature • Decrease injection speed • Use appropriately sized barrel Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded-in stress Burning Process related Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase injection speed Insufficient packing • Increase hold pressure and time Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size Melt and/or mold too hot • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Troubleshooting Recommendations Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Increase screw decompression Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase packing pressure Troubleshooting Recommendations (continued) Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Increase cooling time Warp Process related • Increase cooling time • Increase pack pressure • Increase pack time Mold design • Inspect for non-uniform mold cooling Part design • Inspect for non-uniform wall thickness Temperature control unit incorrect temperature • Check settings • Inspect thermocouple Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

Inspect thermocouple 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

www.avient.com Copyright © 2020, Avient Corporation.

Key: A = 4% Amosorb SolO2-2 + Fortis Amber-1 @ 0.09%; B = 50% Regrind A + 50% Virgin PET; C = 50% Regrind A + 50% Virgin PET + Fortis Amber @ 0.045% REGRIND COMBINATION STUDY - METHODOLOGY 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

These properties, coupled with a wide array of base engineering thermoplastics, deliver the distinct benefits of LubriOne: • Reduced friction and heat buildup between interacting surfaces • Reduced noise and vibration among components in relative motion • Reduced weight and improved design freedom • Lower long–term maintenance costs when grease and other lubricants are eliminated Copyright © 2023, Avient Corporation.

Code de conduite des fournisseurs d’Avient Avient Corporation, ses filiales et ses sociétés affiliées (« Avient ») s’engagent à être une organisation durable de classe mondiale.