MC-24929PE JADE #16-6127 TPG MC-24930PE KIWI #15-0545 TPG MC-24931PE CELERY #13-0442 TPG

FLAMINGO 17-1937-TPG PAPAYA 16-1450-TPG AZURE 16-4529- TPG

With processing speeds up to 1000m/minute and a much lower melting point than PBT (a traditional OFC jacketing material), these new ECCOH™ grades enable faster processing and reduced energy use during manufacturing. As global demand for internet connectivity and data transmission capacity continues to rise, fiber optic cable is replacing traditional copper communication cables at a fast pace.

OnColor™ UL 94 colorants are UL 94 recognized color concentrates (masterbatches) designed to speed up time to market by providing customers with the necessary UL recognition to support the UL listing of their finished products. Check the availability of UL 94 recognized masterbatches for your base resin. Provided UL 94 colorants to gain increased speed to market and improved quality

PRNewswire/ -- 5G technology will provide the backbone for a step-change in performance of mobile devices, allowing ultrafast download speeds and the ability to connect billions of devices through a network.  In particular, the IoT (Internet of Things) will be made much more powerful with 5G, as increased connectivity will allow real-time changes to power and resource needs.  for broadband, including equipment that enables and expands access to high-speed communications throughout the country.

BASE RESIN ABS Drying Temperature 80–90°C Drying Time 2–3 Hours Barrel Temperatures °C Rear Zone 180–210 Center Zone 190–220 Front Zone 200–230 Nozzle 210–240 Mold Temperature 50–80 Screw Speed Moderate Back Pressure 3–10 bar Cushion 5–15 mm Injection Speed Low to medium Injection Pressure Moderate to high Holding Pressure 10–30% of injection pressure Screw Type General purpose Screw L/D 20:1 Screw Compression Ratio 2.0:1–2.5:1 Non-return Check Valve Free flow check ring Nozzle Type Reverse taper Barrel Capacity 30–80% of barrel should be used STARTUP & SHUTDOWN RECOMMENDATIONS Purge Compound 2–3 melt flow PP or purging compound. Incomplete Fill Melt and/or mold temperature too cold • Increase nozzle and barrel temperatures • Check thermocouples and heater bands Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel Gate location and/or size • Relocate gate to non-stress area • Increase gate size to allow higher flow rate and lower molded-in stress Wet material • Check moisture. Fibers on Surface (Splay) Melt temperature too low • Increase injection speed Wet material • Check moisture.

Check settings 2. Reduce screw speed 3. Check for wear on screw, barrel or check ring Delamination Process related 1.

MC-61769PE QUINCE #17-1553 TPG MC-61770PE POPPY #17-1547 TPG MC-61777PE QUINCE #17-1553 TPG

Processing Guidelines Base Resin PA6 Barrel Temperatures °F °C Rear Zone 440–470 227–243 Center Zone 450–480 232–249 Front Zone 460–490 238–254 Nozzle 470–500 243–260 Melt Temperature 470–500 243–260 Mold Temperature 120–180 49–82 Pack and Hold Pressure 50–75% of Injection Pressure Injection Velocity 0.5 in/s–3 in/s 13 mm/s–76 mm/s Back Pressure 50–100 psi 3.4–6.9 Bar Screw Speed 30–70 rpm Cushion 0.25 in 6.35 mm Drying Parameters 2–4 Hours @ 180°F 2–4 Hours @ 82°C Moisture % Allowable 0.08–0.18%* Screw Type General Purpose Screw Screw Compression Ratio 2.0:1– 2.5:1 Screw L/D 20:1 Non-return Check Valve Free Flow Check Ring Nozzle Type Reverse Taper Clamp Pressure 2–3 Tons/in² Barrel Capacity 30-80% of barrel should be used * Avient suggests measuring moisture using a Karl Fischer method or Vapor Pro® moisture analyzer that titrates only for moisture. Cut vent depths to 0.0007″–0.0015″ Draft Angle Maintain a minimum draft angle of 1° per side 4 Artisan Pre-Colored Thermoplastics Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Check thermocouples and heater bands Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel Gate location and/or size • Relocate gate to non-stress area • Increase gate size to allow higher flow rate and lower molded-in stress Wet material • Check moisture. Splay Melt temperature too low • Increase injection speed Wet material • Check moisture.

The graphics, documents, and articles contained on this World Wide Web (www) site and Avient sites elsewhere on the Internet are the copyrighted work of Avient Corporation and contain proprietary trademarks and trade names of the company, its subsidiaries, and joint ventures. The articles, information and works provided in this World Wide Web site and Avient Corporation sites elsewhere on the Internet are provided "AS IS," WITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT, OR OTHERWISE.