Cesa™ Laser Additives Cesa™ Laser Additives allow manufacturers to optimize the use of laser technology to create markings or assemble plastic parts.   Learn more about Silcosperse Laser Marking additives are laser absorbing silicone dispersions that use UV, YAG or fiber laser technologies

Executive Vice President and CFO, will provide insights and commentary on the company's expected second quarter performance as well as the status of the previously announced Clariant Masterbatch acquisition.

Coincident with the acquisition of the Clariant Color business in 2020, we branded the collective enterprise Avient—a new name for a new kind of materials company.

Cesa Fiber Additives for Heat Preservation Technical Bulletin_TW2.28-1 Cesa™ 紅外蓄熱纖維添加劑 熱影像圖片 加熱前表面溫度：20.22°C 技術公告 埃萬特推出新一代應用於紡織纖維的紅外蓄熱添加 劑配方，旨在幫助品牌商能夠更加輕鬆地滿足消費 者對冬裝、運動裝和床上用品輕量舒適的要求。 與普通織物相比，在暴露於波長為320至1100nm 的日光下，使用Cesa™紅外蓄熱纖維添加劑的紡織 品能吸收更多熱量，同時能達到更高的克羅值（服 裝隔熱保暖性能）。 • • • 測試方法：FTTS-FA-010-2007 4.2 設備：紅外線熱像儀 熱源：500W鹵素燈 熱輻射距離：100 cm 加入Cesa紅外蓄熱纖維添加劑 加熱10分鐘後表面溫度：33.85°C 溫度變化：+13.6°C 測試方法 0.9 9°C 8.9°C 5.6°C 0.625 +12.9% +13.6% +1.7% www.avient.com 標準要求 測試結果 GB/T 30127 遠紅外線性能 GB/T 18319-2019 光蓄熱性能 FTTS-FA-010 紅外線性能及蓄熱升溫 GB/T 11048-2008 Method A 熱舒適性 熱阻性能 單位：CLO 人體生理實驗 遠紅外線發射率 ≥0.88 (5-14um) （測試溫度:34°C） 遠紅外線輻射溫升值 ≥1.4°C 最高允許溫升值 ≥6°C 平均溫升值 ≥4.4°C（20分鐘） 平均發射率 ≥ 0.8 (2-22um) （測試溫度: 25°C) 0.81 規定加熱ΔT ≥ 0.5°C （相對於標準） +5.34°C (ΔT) 裸體：0 內褲：0.04 T恤：0.09 厚毛衣：0.35 冬季大衣：0.7 上述所有資料均為參考值 血流量 血流速 血氧濃度（%SpO2） 請聯絡您的埃萬特業務代表以了解 您所在國家或地區是否有售。

Cesa™ Aversive Technology Cesa™ WithStand™ Antimicrobial Additives Laser Marking Colorants: Cesa™ Laser Marking Additives

VALVE-GATED TOOLS IN INJECTION MOLDING GUIDELINES CESA CLEAN ADDITIVES ™ KEY FEATURES Cesa™ Clean Additives • Cesa Clean is a concentrated purge product, not a purge compound. • It can be processed through manifolds, valve-gated tools and small sub gates. • Cesa Clean is 100% recyclable with polyolefin resins and compounds. GUIDELINES FOR USING CESA CLEAN ADDITIVES • Cesa Clean works best when molded maintaining normal (injection) pressure/shear • For best results, Avient recommends a “Running Color Change” which eliminates breaks in the molding cycle • Since the Cesa Clean concentrate will expand, it is recommended to reduce the shot size by 20% • It is designed for use at a let-down ratio (LDR) of 3.0% or (33:1); however, use rate can vary depending on the severity of the contamination but typically is 2.0–4.0% (a use rate higher than 6.0% may not have any positive affect on the cleaning performance) • Using Cesa Clean as a routine part of your color change rotation will allow faster changes and consume a minimal amount of raw material - Note: If the manifold is not cleaned routinely, this process may be more time consuming and additional material will be required • It is best to process at your normal polymer processing temperatures - For best performance, stock temperature should be at least 400°F - If 400°F is achieved during the purging process, no additional activation will occur during the reprocessing of regrind - All parts produced during the “Running Purge Cycle” should be captured as regrind, resulting in a scrap-free color change - If using sequential gates, open and close all gates at the same time while purging the tool - If contamination appears to be coming from one gate, open and close first, and for an extended period of time, to force more material through this location - When cleaning in this manner, pay close attention to shot size - Parts containing the previous or new color plus any Cesa Clean can be used as regrind INTRODUCING CESA CLEAN TO YOUR PROCESS Hand Blend • Hand weigh enough of the Cesa Clean and natural resin mix to equate to 3–5 times the barrel capacity • Use rate should be 3.0% or 33:1 for routine cleaning • For difficult-to-clean tooling, or tooling which is not routinely cleaned, start at 4.0% or 25:1 • Note: Do not attempt to vacuum load more than 15 feet from source as stratification/separation may occur Volumetric Feeder • Calibrate feeder to dispense 3.0% or 33:1 for routine cleaning • For difficult-to-clean tooling, or tooling which is not routinely cleaned, start at 4.0% or 25:1 • This style of feeder is highly recommended for at-the-throat metering of Cesa Clean Blending Units Most blenders have an extra bin for an additive • Fill the additive bin with Cesa Clean • Set blender to introduce the Cesa Clean at 2.0 to 4.0% • Note: Do not air convey any further than 15 feet as Cesa Clean has a high density and may separate from the mix. GETTING STARTED TIMING IS THE KEY TO A RUNNING COLOR CHANGE Hand Blend • Have the purge blend ready to load • If hopper contains a mixture of resin, color and/ or regrind, it should be run dry or drained before beginning the color change, keeping the screw full so press cycle continues • Run the main resin hopper dry or shut off hopper to hand feed at the throat • Once press is clean, slide hopper in place and proceed with next color-resin blend • The next color can be added while Cesa Clean is still in the barrel • When splay is no longer visible in parts, reset shot size, parts should be ready to pack (Single) Volumetric/Gravimetric Metering Unit at the Throat • Empty and clean feeder while press continues to run • Add Cesa Clean to the feeder color hopper and calibrate to a 3.0% use rate • When press is clean, start next color • When splay is no longer visible in parts, reset shot size, parts should be ready to pack • Note: If an open/unused secondary feeder is installed, use it for the Cesa Clean concentrate Central Blending Unit • Thoroughly clean unit while continuing to mold parts, keeping a resin feed to the press • Using a clean open hopper or regrind hopper, add the Cesa Clean concentrate • Set blender for additive/color to 3.0% • Once press is clean, drain hopper and/or central blending unit while continuing to mold parts • Begin new color and continue to mold parts • When splay is no longer visible in parts, reset shot size, parts should be ready to pack Process Adjustments That Can Help • Increase back pressure • Increase screw speed • Increase injection speed (in some tools maximum injection speed can facilitate cleaning) • Reduce mold close time (faster cycle) • Always remember a stock temperature of 400°F is essential When press and tool are clean, return all settings to standard production process profile.

CESA Fiber Additives for Heat Preservation ProductBulletin_CN4.27-2 CESA™ 红外蓄热纤维添加剂 1.844.4AVIENT www.avient.com 版权所有©2021 埃万特公司。 CESA™ 红外蓄热纤维添加剂是一种配方添加剂， 满足GB/T 30127-2013标准，可用于增强合成纤 维纺织品的保暖性能。 相较于常规织物，使用此 CESA纤维添加剂织物在暴露阳光下能够吸收更多 的热量。

Cesa™ Clean masterbatch additives are formulated to effectively clean process tooling and machinery during material or color changeovers. Cesa™ Clean Additives WHEN TO USE CESA CLEAN As a best practice, Cesa Clean adds value when used for: • Color changeovers • Material and formulation changes • Shutdown or startup • Machine maintenance WHY USE CESA CLEAN Some of the ways you can benefit from consistently using Cesa Clean: • Improve production uptime with faster color changeovers • Reduce wasted melt puddle material • Reduce resin use during purging • Non-abrasive and safe to use on precision equipment PRODUCT BULLETIN Cesa Clean solutions are available for use in a variety of processing conditions and operating temperatures.

Avient acquired the Clariant Masterbatch business (CMB) on July 1, 2020 (the “Acquisition Date”). It’s in this spirit that we joined legacy PolyOne and the Clariant Masterbatch business, two complementary businesses, and formed a new one that we’ve named Avient. We are better together through: Keeping Safety First — PolyOne and Clariant are both ACC Responsible Care® companies, and nothing is more important than the health, safety and well-being of our people.

Cesa™ Low Retention Additives Additives for Polyolefin Films: Cesa™