Base Resin PC PC/PSU PES PEI PP ABS PEEK PA Barrel Temperatures* °F (°C) Rear Zone 530–560 (277–293) 550–575 (288–302) 660–700 (349–371) 675–725 (357–385) 390–420 (199–216) 425–460 (219–238) 680–730 (360–388) 430–500 (221–260) Center Zone 515–560 (269–288) 540–565 (282–296) 650–690 (343–366) 655–710 (352–377) 380–405 (193–207) 415–450 (213–232) 670–710 (354–377) 420–490 (216–254) Front Zone 510–525 (266–274) 530–555 (277–291) 640–680 (338–360) 655–700 (346–371) 370–395 (188–202) 405–440 (207–227) 650–690 (343–366) 410–480 (210–249) Nozzle 520–535 (271–280) 540–565 (282–296) 650–690 (343–366) 665–710 (352–377) 380–400 (193–204) 415–450 (213–232) 660–700 (349–371) 420–490 (216–254) Melt Temperature 525–560 (274–293) 530–580 (277–304) 650–700 (343–371) 660–730 (349–388) 375–395 (191–202) 410–460 (210–238) 650–730 (343–388) 420–500 (216–260) Mold Temperature 175–250 (80–121) 160–220 (71–104) 280–350 (138–177) 275–350 (135–177) 100–135 (38–57) 150–180 (66–82) 300–425 (149–219) 160–230 (71–110) Pack & Hold Pressure 50%–75% of Injection Pressure Injection Velocity in/s 0.5–2.0 Back Pressure psi 50 Screw Speed rpm 40–70 40–70 40–70 40–70 40–70 40–70 40–70 40–70** Drying Parameters °F (°C) 6 hrs @ 250 (121) 4 hrs @ 250 (121) 4 hrs @ 275 (135) 4 hrs @ 250 (121) 3 hrs @ 300 (150) 2 hrs @ 200 (93) 3 hrs @ 275 (135) 4 hrs @ 180 (82) Cushion in 0.125–0.250 Screw Compression Ratio 2.0:1–2.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose Reverse Taper Clamp Pressure 5–6 Tons/in2 * A reverse temperature profile is important to obtain optimum conductive properties. Gate type should be selected based on location and part geometry. • Gate diameters equivalent to 50%–75% of the average wall thickness are recommended. • Land lengths of 0.020"–0.035" (0.50mm–0.90mm) are typically recommended. Cold Slug Wells • Place these wells at the base of the sprue to capture the cold material first emerging from the nozzle. • Place wells at every 90° bend in the runner system. • Well depths approximately 1.5 times the diameter of the runner provide the best results.

Injection Molding Parameters Base Resin PPA PPS PA 6/6 PA 12 Barrel Temperatures °F (°C)* Rear Zone 550–580 (288–305) 550–580 (288–305) 440–490 (227–254) 440–480 (227–250) Center Zone 560–600 (293–316) 560–615 (293–324) 470–510 (243–266) 460–510 (238–266) Front Zone 580–620 (304–327) 590–630 (310–333) 490–540 (254–282) 480–520 (250–271) Nozzle 575–615 (302 –324) 600–625 (316–330) 520–570 (271–300) 500–530 (260–277) Melt Temperature °F (°C) 575–615 (302–324) 600–625 (316–330) 520–570 (271–300) 500–530 (260–277) Mold Temperature °F (°C) 250–300 (121–150) 250–300 (121–150) 150–200 (66–93) 150–200 (66–93) Pack and Hold Pressure 50–80% of Injection Pressure Injection Velocity 1.0–3.0 in/sec Back Pressure 25–100 psi Screw Speed 25–75 rpm Drying Parameters °F (°C) 6 hours @ 175 (80) 6 hours @ 300 (150) 3 hours @ 180 (82) 3 hours @ 180 (82) Cushion 0.125–0.250 in Screw Compression Ratio 2.5:1–3.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose Reverse Taper Reverse Taper Clamp Pressure 4–5 tons/in2 of projected area of cavities and runner system * Barrel temperatures should be elevated for compounds designed for electrical insulative properties. Gate type should be selected based on location and part geometry. 2. Place these wells at the base of the sprue to capture the cold material first emerging from the nozzle. 2.

LUBRIONE™ INTERNALLY LUBRICATED FORMULATIONS PRODUCT SELECTION GUIDE PRODUCT DESCRIPTION UNITS TEST METHOD NN–000/15T BLACK NN–20GF– 10GB/13T–2S BLACK NN–30GF/10T WHITE LB8900-0001 30GF/15T NATURAL LB8900-0002 30GF/13T-2S NATURAL LB8900-0003 18T-2S NATURAL ATT–000/5T BLACK AT–000/18T– 2S NATURAL 5209 FPL 20 NATURAL PS–30GF/2S NATURAL LB5210–0237 1B NATURAL PC–10CF/15T BLACK Base Polymer PA 66 PA 66 PA 66 PK PK PK POM POM POM PBT PP PC General Properties Specific Gravity g/cm3 ASTM D792 1.23 1.46 1.47 1.56 1.55 1.33 1.38 1.47 1.51 1.54 1.13 1.31 Molding Shrinkage ASTM D955 Flow % 1.0–2.0 0.20–0.50 0.50–1.0 0.30–0.60 0.20–0.40 1.7–2.3 1.5–2.0 2.0–3.0 2.0–3.0 0.20–0.40 0.10–0.30 0.10–0.30 Water Absoprtion (23°C, 24 hr.) % ASTM D570 0.8 – 0.050–1.0 0.3 0.4 0.4 0.050 – 0.050 – – – Mechanical Properties Tensile Modulus(1) MPa ASTM D638 2650 9650 9790 8050 7380 1250 965 1770 2420 8620 4140 – Tensile Strength(1) (Yield) MPa ASTM D638 61.4 119 122 119 94 47 35 40 45 108 72.4 90 Tensile Elongation(1) (Break) % ASTM D638 3.0–5.0 1.0–3.0 1.5 3 2 35 40 30 26 3 – – Flexural Modulus MPa ASTM D790 2760 6890 6890 7380 6410 1300 1080 1740 1790 6690 4840 5500 Flexural Strength MPa ASTM D790 108 172 214 182 167 55 41.4 62.7 68.3 165 110 130 Coefficient of Friction ASTM D1894 vs. Steel – Static 0.25 0.46 0.18 0.15 0.12 0.19 0.11 0.14 0.13 0.24 0.17 0.17 Impact Notched Izod Impact (23°C, 3.18 mm, Injection Molded) J/m ASTM D256A 41 64(6) 110 107 107 70 80 37 37 75 – 69 Thermal Properties Heat Deflection Temperature ASTM D648 0.45 MPa °C 215(6) – 250 215 216 184 152 151(6) 153(6) 218(6) – – 1.8 MPa °C 65(6) 239(7) 244(6) 210 210 75 94 81.1(6) 88 197(6) – 135(5) Electrical Properties Surface Resistivity ohms/sq ASTM D254 – – – 1.30x1012 1.9x1012 5.2x1012 – – – – – 1.0x109 Dielectric Strength (Short Time) kV/mm – – 8.5 – – – – – – – – – Flammability Flame Rating Class UL 94 HB – – HB HB HB – HB – – – – LubriOne™ Internally Lubricated Formulations NOTES (1) Type I, 5.1mm/min (2) Type I, 21.3 mm/min (3) Type I, 50 mm/min (4) Type I, 5.1mm/min, Break (5) 3.2 mm thick, Unannealed (6) 6.35 mm thick, Unannealed (7) 3.2 mm thick, Annealed PRODUCT DESCRIPTION UNITS TEST METHOD LB6000- 5024 RS HI Natural LB6000- 5021 RS S1 Black LB6000- 5021 RS X2 Black LB6000- 5019 X1 Black LB6700- 5001 RS AF Black NN- 000/01M Black SO REC LB6600- 5030 RS Grey LB3300- 5010 RS Natural LB3300- 5005 RS Natural REC LB3220- 5001 RS C Natural X1 LB8900- 5010 GP Grey LB8900- 5006 RS PE Natural LB8900- 5004 RS PE Natural LB4200- 5022 Black LB4200- 5023 Natural Base Polymer PA 6 PA6/PA66 PA66 PBT PC PKE POM Lubricant UHMWPE1 UHMWPE UHMWPE UHMWPE UHMWPE MoS22 Graphite UHMWPE UHMWPE UHMWPE Graphite UHMWPE UHMWPE MoS2 UHMWPE Filler type GF10 GF30 GF30 GF50 GF50 Unfilled GF33 GF20 MI20 GF10 Unfilled GF20 GF30 Unfilled Unfilled General Properties Specific Gravity g/cm3 ISO 1183 1.18 1.35 1.39 1.55 1.58 1.14 1.44 1.42 1.46 1.23 1.26 1.34 1.43 1.4 1.35 Mechanical Properties Tensile Modulus (23°C) MPa ISO 527-1 4250 9500 9000 15500 16600 3500 10600 6300 3330 4000 1630 5300 9250 2470 2150 Tensile Strength (Yield, 23°C) MPa ISO-527-2 97 150 160 205 200 85 164 102 55 60 60 108 99.1 55 50 Tensile Elongation (Break, 23°C) % ISO-527-2 12 2.5 3 2.7 2.4 3.4 2.0 4.2 8 2.5 46 3.7 1.5 11 11 Flexural Strength (23°C) MPa ISO 178 103 – – 285 265 108 215 127 78 85 38 155 117 73 68 Flexural Modulus (23°C) MPa ISO 178 3250 – – 12400 11100 2690 9000 4700 3000 3100 1380 4600 5450 2210 2070 Impact Charpy Notched Impact Strength (23°C, Injection Molded) kJ/m^2 ISO 179 14 12 10 15 10 3 6 7.7 4.3 12 15 10 7.6 8 5 Charpy Unnotched Impact Strength (23°C, Injection Molded) kJ/m^2 ISO 179 82 55 61 75 60 65 50 47 69 - NB 63 36 NB NB Thermal Properties Deflection Temperature Under Load 1.8 Mpa, Unannealed °C ISO 75-2/A 107 – – 204 – 73 235 – – – 90 210 204 86 80 Cofficient of Friction (CoF) & Wear Rate CoF vs. These properties, coupled with a wide array of base engineering thermoplastics, deliver the distinct benefits of LubriOne: • Reduced friction and heat buildup between interacting surfaces • Reduced noise and vibration among components in relative motion • Reduced weight and improved design freedom • Lower long–term maintenance costs when grease and other lubricants are eliminated Copyright © 2023, Avient Corporation.

They are based on management’s expectations that involve a number of business risks and uncertainties, any of which could cause actual results to differ materially from those expressed in or implied by the forward-looking statements. . Develop and implement solutions to end plastic waste while supporting AEPW $1.5B investment in key initiatives. 2030 SUSTAINABILITY TARGETS 15 PEER COMPARISONS 16 $442 $457 $560 2019PF 2020PF 2021E $1.74 $1.93 $2.80 2019PF 2020PF 2021E FULL YEAR 2019 – 2021 ORGANIC GROWTH (TOTAL COMPANY) 17 Sales Adjusted EBITDA $3,981 $3,783 $4,300 2019PF 2020PF 2021E + 8% Adjusted EPS (1) Financial information is pro forma to include a full year of Clariant Masterbatch business acquisition (1) (1) (in millions) (in millions) (1)(1) + 27% + 61% (1) (1) As a specialty formulator, we don’t require significant capital investment, as compared to the base resin raw material suppliers we purchase from. APPENDIX Performance Additives 15% Pigments 15% TiO2 12% Dyestuffs 4%Polyethylene 10% Nylon 5% Polypropylene 4% Other Raw Materials 29% Styrenic Block Copolymer 6% ~1/3 hydrocarbon based (Grey shaded materials are hydrocarbon based, includes portion of “Other Raw Materials”) Non-hydrocarbon based materials 23 • Exiting 2020, the majority of hydrocarbon based raw material markets were experiencing price inflation and tight inventory • Winter Storm Uri in the Gulf Coast caused further stress on the situation for 2021 • Raw materials most impacted include polyethylene, polypropylene and nylon • We purchase over 8,000 different raw materials to formulate our customized solutions and unique specifications Annual Purchases RAW MATERIAL UPDATE Based on 2020 pro forma purchases, excludes Distribution SEGMENT DATA U.S. & Canada 50% EMEA 26% Asia 16% Latin America 8% 2020 SEGMENT, END MARKET AND GEOGRAPHY 25 GEOGRAPHY REVENUESEGMENT FINANCIALS Consumer 23% Packaging 21%Industrial 15% Wire & Cable 6% Building & Construction 6% Electrical & Electronics 4% END MARKET REVENUE Transportation 10% Healthcare 15% All data reflects 2020 Pro forma for acquisition of the Clariant Masterbatch business. (1) The total company sales and EBITDA of $3,783M and $457M, respectively, include intercompany sales eliminations and corporate costs $2,043M $331M $709M $124M $1,110M $70M Sales EBITDA Distribution Specialty Engineered Materials Color Additives and Inks $457M$3,783M (1) Packaging 35% Consumer 23% Healthcare 8% Industrial 14% Building & Construction 8% Transportation 7% Wire & Cable 3% Electrical & Electronics 2% C O L O R , A D D I T I V E S & I N K S 2020 PF REVENUE | $2 .0 BILLION US & Canada 31% EMEA 40% Asia 22% Latin America 7% END MARKET REGION 26 2020 figures Pro forma for acquisition of the Clariant Masterbatch business S P E C I A LT Y E N G I N E E R E D M AT E R I A L S Consumer 24% Healthcare 10% Packaging 6% Wire & Cable(1) 24% Electrical & Electronics 13% Transportation 11% Industrial 10% Building & Construction 2% 2020 REVENUE | $709 MILLION END MARKET US & Canada 58% EMEA 23% Asia 19% REGION 27 (1) Approximately 50% of Wire and Cable sales are associated with Fiber Optic Cabling DI S TR IBU T I ON 2020 REVENUE | $1 .1 B ILL ION Healthcare 29% Consumer 25% Packaging 2% Industrial 20% Transportation 14% Electrical & Electronics 5% Building & Construction 4% Wire & Cable 1% US & Canada 82% Asia 3% Latin America 15% END MARKET REGION K E Y S U P P L I ER S 28 TOTA L C O M PA N Y R E G I O N A L S A L E S BY END MARKET Packaging 32% Consumer 27% Healthcare 12% Industrial 6% Wire & Cable 6% Building & Construction 4% Electrical & Electronics 9% Asia (16% of sales) Transportation 4% Packaging 34% Consumer 16%Healthcare 5% Industrial 17% Wire & Cable 10% Building & Construction 8% Electrical & Electronics 3% EMEA (26% of sales) Transportation 7% 2020 figures Pro forma for acquisition of the Clariant Masterbatch business 29 Transportation 10% Consumer 26% Healthcare 19% Packaging 13% Industrial 16% Wire & Cable 7% Building & Construction 5% Electrical & Electronics 4% US & Canada (50% of sales) Packaging 45% Consumer 29% Healthcare 6% Industrial 8% Building & Construction 3% Electrical & Electronics 2% Wire & Cable 1% LATAM (8% of sales) Transportation 6% Reconciliation of Non-GAAP Financial Measures (Unaudited) (Dollars in millions, except for per share data) Three Months Ended March 31, 2021 Reconciliation to Condensed Consolidated Statements of Income GAAP Results Special Items Adjusted Results Income from continuing operations before income taxes $ 102.6 $ 2.4 $ 105.0 Income tax expense - GAAP (22.9) — (22.9) Income tax impact of special items — (0.9) (0.9) Tax adjustments — 1.1 1.1 Net income attributable to noncontrolling interests (0.4) — (0.4) Net income from continuing operations attributable to Avient shareholders $ 79.3 $ 2.6 $ 81.9 Net income / EPS $ 0.86 0.03 $ 0.89 Weighted-average diluted shares 92.2 92.2 92.2 Reconciliation to Consolidated Statements of Income Three Months Ended March 31, 2021 Operating income - GAAP $ 120.4 Special items in operating income 2.4 Adjusted Operating income $ 122.8 1 Business Segment Operations Three Months Ended March 31, Year Ended December 31, 2021 2020 2020 2019 2018 Sales: Color, Additives and Inks $ 609.3 $ 256.5 $ 1,502.9 $ 1,003.8 $ 1,046.5 Specialty Engineered Materials 216.5 185.3 708.8 745.7 645.8 Distribution 362.7 289.5 1,110.3 1,192.2 1,265.4 Corporate and eliminations (26.2) (19.8) (79.9) (79.0) (76.7) Sales $ 1,162.3 $ 711.5 $ 3,242.1 $ 2,862.7 $ 2,881.0 Gross margin: Color, Additives and Inks $ 197.5 $ 89.4 $ 484.4 $ 338.4 $ 353.4 Specialty Engineered Materials 64.7 52.6 207.6 200.2 171.7 Distribution 39.3 33.6 124.0 132.1 125.8 Corporate and eliminations 0.9 (4.1) (31.7) (13.5) (26.1) Gross margin $ 302.4 $ 171.5 $ 784.3 $ 657.2 $ 624.8 Selling and administrative expense: Color, Additives and Inks $ 108.7 $ 48.9 $ 303.6 $ 191.0 $ 194.9 Specialty Engineered Materials 30.5 30.3 113.2 116.5 99.4 Distribution 15.3 14.2 54.5 56.7 54.3 Corporate and eliminations 27.5 25.3 123.7 136.2 97.6 Selling and administrative expense $ 182.0 $ 118.7 $ 595.0 $ 500.4 $ 446.2 Operating income: Color, Additives and Inks $ 88.8 $ 40.5 $ 180.8 $ 147.4 $ 158.5 Specialty Engineered Materials 34.2 22.3 94.4 83.7 72.3 Distribution 24.0 19.4 69.5 75.4 71.5 Corporate and eliminations (26.6) (29.4) (155.4) (149.7) (123.7) Operating income $ 120.4 $ 52.8 $ 189.3 $ 156.8 $ 178.6 Earnings before interest, taxes, depreciation and amortization (EBITDA): Color, Additives and Inks $ 116.2 $ 51.4 $ 255.9 $ 190.1 $ 202.8 Specialty Engineered Materials 42.0 29.8 124.4 113.2 95.5 Distribution 24.2 19.5 70.2 75.9 72.2 Corporate and eliminations (24.9) (28.0) (146.2) (144.3) (119.3) Other income, net 1.5 1.6 24.3 12.1 (12.9) EBITDA $ 159.0 $ 74.3 $ 328.6 $ 247.0 $ 238.3 EBITDA as a % of Sales: Color, Additives and Inks 19.1 % 20.0 % 17.0 % 18.9 % 19.4 % Specialty Engineered Materials 19.4 % 16.1 % 17.6 % 15.2 % 14.8 % Distribution 6.7 % 6.7 % 6.3 % 6.4 % 5.7 % 2 Reconciliation of Pro Forma EBITDA - Color, Additives and Inks Three Months Ended March 31, Year Ended December 31, 2021 2020 2020 2019 2018 Sales: Color, Additives and Inks $ 609.3 $ 256.5 $ 1,502.9 $ 1,003.8 $ 1,046.5 Clariant MB pro forma adjustments(1) — 279.4 540.4 1,118.6 1,209.8 Pro forma sales $ 609.3 $ 535.9 $ 2,043.3 $ 2,122.4 $ 2,256.3 Operating income: Color, Additives and Inks $ 88.8 $ 40.5 $ 180.8 $ 147.4 $ 158.5 Clariant MB pro forma adjustments(1) — 23.0 45.0 72.9 80.3 Pro forma operating income $ 88.8 $ 63.5 $ 225.8 $ 220.3 $ 238.8 Depreciation & amortization: Color, Additives and Inks $ 27.4 $ 10.9 $ 75.1 $ 42.7 $ 44.3 Clariant MB pro forma adjustments(1) — 15.1 30.1 60.3 61.2 Pro forma depreciation & amortization $ 27.4 $ 26.0 $ 105.2 $ 103.0 $ 105.5 Earnings Before Interest, Taxes, Depreciation and Amortization (EBITDA): Color, Additives and Inks $ 116.2 $ 51.4 $ 255.9 $ 190.1 $ 202.8 Clariant MB pro forma adjustments(1) — 38.1 75.1 133.2 141.5 Pro forma EBITDA $ 116.2 $ 89.5 $ 331.0 $ 323.3 $ 344.3 Pro forma EBITDA as a % of Sales 19.1 % 16.7 % 16.2 % 15.2 % 15.3 % Three Months Ended March 31, 2020 Reconciliation of Pro Forma Adjusted Earnings per Share Avient Special Items Adjusted Avient Clariant MB Pro Forma Adjustments(1) Pro Forma Adjusted Avient Sales $ 711.5 $ — $ 711.5 $ 279.4 $ 990.9 Operating income 52.8 9.7 62.5 23.0 85.5 Interest expense, net (9.4) — (9.4) (12.8) (22.2) Other income, net 1.6 (0.1) 1.5 — 1.5 Income taxes (11.9) (1.0) (12.9) (2.4) (15.3) Net income from continuing operations attributable to Avient shareholders $ 33.1 $ 8.6 $ 41.7 $ 7.8 $ 49.5 Weighted average diluted shares 86.7 Impact to diluted shares from January 2020 equity offering 6.1 Weighted average diluted shares 92.8 EPS $ 0.53 (1) - Pro forma adjustments for the periods prior to the acquisition date (July 1, 2020) and to give effects of the financing for the acquisition 3 Three Months Ended June 30, 2020 Reconciliation of Pro Forma Adjusted Earnings per Share Avient Special Items Adjusted Avient Clariant MB Pro Forma Adjustments(2) Pro Forma Adjusted Avient Sales $ 609.1 $ — $ 609.1 $ 261.1 $ 870.2 Operating income $ 38.0 $ 9.0 $ 47.0 $ 22.0 $ 69.0 Interest expense, net (16.2) — (16.2) (5.3) (21.5) Other income, net 9.5 (0.3) 9.2 — 9.2 Income taxes (7.9) 0.7 (7.2) (3.8) (11.0) Net income attributable to non controlling interests (0.4) — (0.4) — (0.4) Net income from continuing operations attributable to Avient shareholders $ 23.0 $ 9.4 $ 32.4 $ 12.9 $ 45.3 Weighted average diluted shares 91.8 Impact to diluted shares from January 2020 equity offering 15.3 Pro forma weighted average diluted shares 107.1 Pro forma adjusted EPS $ 0.42 (2) - Pro forma adjustments for the periods prior to the acquisition date (July 1, 2020) and to give effects of the financing for the acquisition Year Ended December 31, Reconciliation to Adjusted EBITDA 2020 2019 2018 Net income from continuing operations – GAAP $ 133.8 $ 75.7 $ 87.4 Income tax expense 5.2 33.7 14.4 Interest expense 74.6 59.5 62.8 Debt extinguishment cost — — 1.1 Depreciation and amortization from continuing operations 115.0 78.1 72.6 EBITDA $ 328.6 $ 247.0 $ 238.3 Special items, before tax 66.2 61.7 59.5 Interest expense included in special items (10.1) — — Accelerated depreciation included in special items (3.2) — (3.0) Adjusted EBITDA $ 381.6 $ 308.7 $ 294.8 4 Year Ended December 31, 2020 Reconciliation of Pro Forma Adjusted Earnings per Share Avient Special Items Adjusted Avient Clariant MB Pro Forma Adjustments(3) Pro Forma Adjusted Avient Sales $ 3,242.1 $ — $ 3,242.1 $ 540.4 $ 3,782.5 Operating income $ 189.3 $ 73.7 $ 263.0 $ 45.0 $ 308.0 Interest expense, net (74.6) 10.1 (64.5) (18.1) (82.6) Other income, net 24.3 (17.6) 6.7 — 6.7 Income taxes (5.2) (41.4) (46.6) (6.2) (52.8) Net income attributable to noncontrolling interests (1.8) — (1.8) — (1.8) Net income from continuing operations attributable to Avient shareholders $ 132.0 $ 24.8 $ 156.8 $ 20.7 $ 177.5 Weighted average diluted shares 90.6 Impact to diluted shares from January 2020 equity offering 1.5 Pro forma weighted average diluted shares 92.1 Pro forma adjusted EPS $ 1.93 Reconciliation of Pro Forma Adjusted EBITDA from continuing operations Operating income and other income, net $ 213.6 $ — $ 56.1 $ 269.7 $ 45.0 $ — $ 314.7 Depreciation and amortization 115.0 (3.2) 111.8 30.1 141.9 EBITDA from continuing operations $ 328.6 $ 52.9 $ 381.5 $ 75.1 $ 456.6 Year Ended December 31, 2019 Reconciliation of Pro Forma Adjusted Earnings per Share Avient Special Items Adjusted Avient Clariant MB Pro Forma Adjustments(1) Pro Forma Adjusted Avient Sales $ 2,862.7 $ — $ 2,862.7 $ 1,118.6 $ 3,981.3 Operating income $ 156.8 $ 71.7 $ 228.5 $ 72.9 $ 301.4 Interest expense, net (59.5) — (59.5) (33.4) (92.9) Other income, net 12.1 (10.0) 2.1 — 2.1 Income taxes (33.7) (5.9) (39.6) (9.1) (48.7) Net income attributable to noncontrolling interests (0.2) — (0.2) — (0.2) Net income from continuing operations attributable to Avient shareholders $ 75.5 $ 55.8 $ 131.3 $ 30.4 $ 161.7 Weighted average diluted shares 77.7 Impact to diluted shares from January 2020 equity offering 15.3 Pro forma weighted average diluted shares 93.0 Pro forma adjusted EPS $ 1.74 Reconciliation of Pro Forma Adjusted EBITDA from continuing operations Operating income and other income, net $ 168.9 $ — $ 61.7 $ 230.6 $ 72.9 $ — $ 303.5 Depreciation and amortization 78.1 — 78.1 60.3 138.4 EBITDA from continuing operations $ 247.0 $ 61.7 $ 308.7 $ 133.2 $ 441.9 (3) - Pro forma adjustments for the periods prior to the acquisition date (July 1, 2020) and to give effects of the financing for the acquisition 5 AVNT First Quarter 2021 Earnings Presentation no recs.pdf AVNT First Quarter 2021 Earnings Presentation.pdf AVNT First Quarter 2021 Earnings Presentation.pdf AVNT First Quarter 2021 Earnings Presentation.pdf 4.29 127pm Q1 21 IR Deck Version non-GAAP Recs (002).pdf

Building on the positive start to the year, we delivered a strong second quarter, highlighted by broad-based growth across all regions and most end markets,” said Dr. They are based on management's expectations that involve a number of business risks and uncertainties, any of which could cause actual results to differ materially from those expressed in or implied by the forward-looking statements. Senior management believes these measures are useful to investors because they allow for comparison to Avient's performance in prior periods without the effect of items that, by their nature, tend to obscure Avient's operating results due to the potential variability across periods based on timing, frequency and magnitude.

They are based on management’s expectations that involve a number of business risks and uncertainties, any of which could cause actual results to differ materially from those expressed in or implied by the forward-looking statements. National Defense budget of $842 billion submitted to Congress in Q1 2023 • European NATO members annual defense spend expected to increase by up to 20% Where Avient Wins:  Dyneema® is the world’s strongest fiber™  One of the highest strength to weight ratios of any material on Earth  Direct relationships with industry leading armor manufacturers  Resistant to most chemicals, UV, and moisture to handle any environment Avient Confidential 18 DEFENSE Source: US Department of Defense, defense.gov, NATO18 Source: TRANSPORTATION • Increased EPA regulations requiring improved fuel efficiency, enabled in part by lower-weight vehicles • Automakers preparing for 2/3 of U.S. vehicles to be 100% electric by 2032 Where Avient Wins:  Lightweight panels that establish both strength and stiffness resulting in decreased energy usage, lower emissions  Long-lasting Color applications to resist UV exposure, temperature fluctuations and exceed the stylistic requirements of global automakers 19 $130 $530 Q2 FY $0.60 $2.40 Q2 FY 2023 GUIDANCE 20 Sales Adjusted EBITDA $845 $3,400 Q2 FY Adjusted EPS (in millions) (in millions) CASH FLOW / LEVERAGE 21 • Maintaining free cash flow and leverage guidance from February earnings call • IT investment to further integrate acquired businesses and capture operational efficiencies • Restructuring actions to streamline operations and improve profitability, primarily in Europe ($ millions) 2023E Cash Flow from Operating Activities 350$ Less: Run-Rate CapEx (110) CapEx for IT System Upgrade (25) CapEx for Restructuring (15) Total CapEx (150) Free Cash Flow 200$ Adjusted EBITDA 530$ Net Debt / Adjusted EBITDA 2.9x LONG-TERM REVENUE GROWTH DRIVERS Growth Drivers Long-Term Growth Rate Sustainable Solutions 8–12% Healthcare 8–10% Composites 10% Asia / LATAM 5% Other (GDP growth) 2–3% Avient 6.5% 22 Sustainable Solutions 32% Asia / LATAM 15% Composites 8% Healthcare 6% Other (GDP Growth) 39% • Virtual presentation to be held September 20, 2023 • The company will be conducting an investor-focused presentation around our sustainability solutions portfolio Avient Confidential 23 SUSTAINABILITY INVESTOR DAY 23 $340M $405M $455M $550M $790M $915M 2016 2017 2018 2019 2020PF** 2021 2022PF*** SUSTAINABILITY FOR A BETTER TOMORROW Revenue From Sustainable Solutions* 2016-2022 ($ in millions) Organic Future Growth Revenue Assumptions From Sustainable Solutions: 8 - 12% 24 *Avient Sustainable Solutions definitions aligned with FTC 2012 Guide for the Use of Environmental Marketing Claims (“Green Guides”) **2020 is Pro Forma to include full year of the Clariant Color business ***2022 is Pro Forma for the acquisition of Avient Protective Materials and the divestiture of Distribution $1,175M Lightweighting Eco-Conscious Recycle Solutions VOC Reduction Sustainable Infrastructure Human Health & Safety Reduced Energy Use Bio-polymers SUSTAINABILITY NEEDS BY MARKET B&C • Eco-Conscious • Carbon footprint • Resource conservation Healthcare • Carbon footprint • Bio based content • Eco-Conscious Automotive • Light weighting • Recycled Content • VOC reduction Consumer • Recycle Solutions • Light weighting • Carbon Footprint Packaging • Recycle Solutions • Light weighting • Food waste reduction Common Theme: CO2 Emission Goals Increasing Single-Use Plastic Regulation 25 INVESTING IN INNOVATION S U S T A I N A B I L I T Y P O R T F O L I O 26 AP P EN D IX 29 RAW MATERIAL 2022 ANNUAL PURCHASES Performance Additives 16% Pigments 12% TiO2 10% Dyestuffs 2% Polyethylene 11% Nylon 6% Polypropylene 5% Styrenic Block Copolymer 5% Other Raw Materials 33% ~40% hydrocarbon based (Grey shaded materials are hydrocarbon based, includes portion of “Other Raw Materials”) Non-hydrocarbon based materials • Cost inflation decelerating, particularly for hydrocarbon-based raw materials 2022 pro forma results for the acquisition of Avient Protective Materials SEGMENT DATA U.S. & Canada 40% EMEA 37% Asia 18% Latin America 5% 2022 PRO FORMA SEGMENT, END MARKET AND GEOGRAPHY GEOGRAPHY REVENUESEGMENT FINANCIALS Consumer 20% Packaging 24% Industrial 15% Building and Construction 10% Telecommunications 4% Energy 4% Defense 6% END MARKET REVENUE $2,355M $402M $1,300M $272M Sales EBITDA Specialty Engineered Materials Color Additives and Inks $592M$3,653M (1) Transportation 9% Healthcare 8% 31 (1) Total company sales and adjusted EBITDA of $3,653M and $592M, respectively, include intercompany sales eliminations and corporate costs C O L O R , A D D I T I V E S & I N K S 2022 REVENUE | $2 .4 B ILL ION US & Canada 34% EMEA 38% Asia 20% Latin America 8% END MARKET REGION 32 Packaging 34% Consumer 21% Healthcare 8% Industrial 15% Transportation 8% Building & Construction 11% Telecommunications 1% Energy 2% S P E C I A LT Y E N G I N E E R E D M AT E R I A L S 2022 PRO FORMA REVENUE | $1 .3 B ILL ION END MARKET US & Canada 52% EMEA 35% Asia 13% REGION 33 Packaging 5% Consumer 19% Healthcare 8%Industrial 16% Transportation 10% Telecommunications 10% Energy 9% Defense 15% Building & Construction 8% Packaging 32% Consumer 27% Healthcare 8% Industrial 14% Building & Construction 5% Telecommunications 3% Energy 1% Defense 1% Asia (18% of sales) Transportation 9% 2022 PROFORMA AVIENT REGIONAL SALES BY END MARKET Packaging 27% Consumer 14% Healthcare 5% Industrial 17% Building & Construction 10% Energy 5% Defense 8% EMEA (37% of sales)Transportation 11% Packaging 13% Consumer 24% Healthcare 12% Industrial 15% Building & Construction 13% Energy 5% Defense 5% US & Canada (40% of sales) Transportation 7% Packaging 56% Consumer 23% Healthcare 4% Industrial 7% Building & Construction 4% Telecommunications 1% LATAM (5% of sales) Transportation 5% Telecommunications 3% Telecommunications 6% 34 PEER COMPARISONS AVIENT IS ASSET LIGHT Capex / Revenue 2023E (%) Avient Specialty Formulators Other Specialty / Chemical Companies Source: Peer data per Bloomberg as of May 31, 2023 Note: Avient reflects 2023 estimated revenue of $3,400 and estimated run-rate CAPEX of $110M. 36 3 2 3 3 4 4 3 3 4 5 5 6 8 9 A vi en t K W R P P G F U L A V Y R P M F M C H U N C E H X L E C L A S H E M N S C L FREE CASH FLOW CONVERSION Source: Peer data per Bloomberg as of May 31, 2023 Note: Free cash flow conversion calculated as (Adjusted EBITDA – Capex) / Adjusted EBITDA. Senior management believes the measures described above are useful to investors because they allow for comparison to Avient's performance in prior periods without the effect of items that, by their nature, tend to obscure Avient's operating results due to the potential variability across periods based on timing, frequency and magnitude.

Gate type should be selected based on location and part geometry. Mold Base Width The “Cheek” width is the width between the edge of the part and the side of the mold base. The total Mold Base Width = Cheek + Part Width + Contact Width (.500") + Space between cavities.

They are based on management’s expectations that involve a number of business risks and uncertainties, any of which could cause actual results to differ materially from those expressed in or implied by the forward-looking statements. Patterson Chairman, President and CEO INTRODUCTION B O B P A T T E R S O N PolyOne Corporation 7 PolyOne Corporation 8 H I S T O R I C P A S T I N S P I R E D F U T U R E S U S T A I N A B I L I T Y A T P O L Y O N E PolyOne Corporation 9 P E O P L E P R O D U C T S P L A N E T S A F E T Y F I R S T PolyOne Corporation 10 1.3 1.1 1.1 0.85 0.65 0.57 0.54 0.97 0.84 0.74 0.74 0.69 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 Injuries per 100 Workers Spartech Acquisition T H E P O L Y O N E A C A D E M Y PolyOne Corporation 11 Leadership Program Participants 2012 2013 2014 2015 47 0 86 2016 2017 125 169 216 Campus Hires 2008 2011 2014 2017 0 25 90 47 S U S T A I N A B L Y I M P A C T I N G D I V E R S E E N D M A R K E T S PolyOne Corporation 12 With emphasis on: • Light-weighting • Reducing packaging materials • Improving recyclability • Reducing spread of infection • Facilitating alternative energy solutions Transportation 18% Industrial 16% Building & Construction 12% Consumer 12% Packaging 11% Healthcare 11% Wire & Cable 9% Electrical & Electronics 6% Appliance 5% P R O D U C T S A N D P O R T F O L I O O P T I M I Z A T I O N PolyOne Corporation 13 R E I N V E S T G R O WD I V E S T ( D S S ) OUR PLANET PolyOne Corporation 14 Energy Saving Projects 26 10% REDUCTION 47 11% REDUCTION Waste Reduction Projects 2,557 LSS Projects Executed 202 PolyOne LSS Blackbelts 2011 2014 2017 202 2008 147 67 0 0 2,557 2008 2017 S U S T A I N A B I L I T Y A T P O L Y O N E PolyOne Corporation 15 P E O P L E P R O D U C T S P L A N E T P E R F O R M A N C E 2009 2010 2011 2012 2013 2014 2015 2016* 2017* A D J U S T E D E P S E X P A N S I O N C O N S E C U T I V E Y E A R S PolyOne Corporation 16 8 $0.13 $0.68 $0.82 $1.00 $1.31 $1.80 $1.96 $2.06 $2.21 *Pro Forma for sale of DSS E A R L Y Y E A R S D E F I N E D B Y S P E C I A L T Y M I X I M P R O V E M E N T PolyOne Corporation 17 2% 65% 2005 2014 $5M $242M + 25% + 33% Specialty OI % of Operating Income C O M M O D I T Y P R U N I N G H E L D O R G A N I C S A L E S F L A T PolyOne Corporation 18 2010 2011 2012 2013 2014 Acquisitions Organic Revenue 531 680130 153 504 618 2014 Q1 2018 R&D / Technical Marketing Sales I N V E S T M E N T I N COMMERCIAL RESOURCES D R I V I N G R E S U L T S PolyOne Corporation 19 Increased commercial headcount Largest organic revenue growth since recession $2.9 $2.9 $3.2 2015 2016 2017 Revenue in billions of $ + 28% + 18% + 23% Total + 10% Organic + 7% S U S T A I N A B L E P A T H T O D O U B L E - D I G I T E P S G R O W T H PolyOne Corporation 20 P E O P L E P R O D U C T S P L A N E T P E R F O R M A N C E Double digit annual EPS growth Expand specialty portfolio with strategic acquisitions Innovate and develop new technologies and services Repurchase 600K-1M shares annually Increase commercial resources 6-8% annually Double acquired company margins Enhance efficiencies through Lean Six Sigma and commercial excellence 5.0% 14.0% 15.0% 16-17% 2006 2017 Platinum Vision Updated Expectations R A I S I N G T H E B A R R O I C D R I V E S S H A R E H O L D E R R E T U R N PolyOne Corporation 21 COMMERCIAL EXCELLENCE PolyOne Corporation 22 M I C H A E L G A R R A T T C O M M E R C I A L R E S O U R C E S I N N O V A T I O NS E R V I C E S T R A T E G I C I N V E S T M E N T I N 3 K E Y A R E A S PolyOne Corporation 23 531 680130 153 504 618 2014 Q1 2018 R&D / Technical Marketing Sales K E Y C O M M E R C I A L I N V E S T M E N T S PolyOne Corporation 24 Increased commercial headcount + 28% + 18% + 23% Generating opportunities 35% more sales calls 25% more marketing campaigns 1,000 new customers, expanding customer base by 5% $1.0B increase in new opportunities Enhancing efficiency 8% reduction of average territory size, enabling greater customer focus 20% more prospecting calls N E W R E S O U R C E S F U E L I N G T H E F U T U R E PolyOne Corporation 25 P O L Y O N E S A L E S F U N N E L +34% 2014 $3.0 billion 2017 $4.0 billion A L I G N I N G W I T H T R E N D S F O R G R O W T H T R A N S P O R T A T I O N P A C K A G I N G H E A L T H C A R E C O N S U M E R PolyOne Corporation 26 Facilitate alternative energy solutions Light- weighting Reduce packaging materials Improve recyclability Reduce spread of infection I N N O V A T I O N PolyOne Corporation 27 3 Horizons of Development Customization 55% M&A 30% Innovation Pipeline 15% Transformational Opportunity for Growth Through M&A Adjacent Opportunity for Growth Through New Product Pipeline Core Business Focus Innovation comes from 3 H O R I Z O N S O F D E V E L O P M E N T PolyOne Corporation 28 Transformational Opportunity for Growth Through M&A Adjacent Opportunity for Growth Through New Product Pipeline Core Business Focus New development adjacent to our existing technology base New development beyond our current technology base Development within our current technology base Service adjacent markets and customers Create new markets, target new customer needs Service existing markets and customers Market Technical I N N O V A T I O N Transformational Opportunity for Growth Through M&A Adjacent Opportunity for Growth Through New Product Pipeline Core Business Focus 3 H O R I Z O N S O F D E V E L O P M E N T PolyOne Corporation 29 Service adjacent markets and customers Create new markets, target new customer needs Service existing markets and customers Market Technical I N N O V A T I O N Gordon/Polystrand – Composites GLS – Thermoplastic Elastomers ColorMatrix – Liquid Color & Additives New development adjacent to our existing technology base New development beyond our current technology base Development within our current technology base Transformational Opportunity for Growth Through M&A Adjacent Opportunity for Growth Through New Product Pipeline Core Business Focus 3 H O R I Z O N S O F D E V E L O P M E N T PolyOne Corporation 30 Service adjacent markets and customers Create new markets, target new customer needs Service existing markets and customers Market Technical I N N O V A T I O N Non-Halogen Flame Retardant Polymers Barrier Technologies Fiber Colorants Advanced Composites Thermoplastic Elastomers New development adjacent to our existing technology base New development beyond our current technology base Development within our current technology base I N N O V A T I O N P I P E L I N E PolyOne Corporation 31 PrototypeFrame Opportunity Scale-up & Test Market Build Business Case Commercial Launch Phase 1 Phase 2 Phase 3 Phase 4 Phase 5 8 5 6 2 1 15 4 10 5 11 4 5 7 Breakthrough Platform Derivative Number of Projects 26 16 20 15 2 79 Color Technologies – – $335 $670 $410 19 $1,415 Barrier Additives – – $160 $255 – 8 $415 Flame Retardant Polymers – – $200 $50 – 14 $250 Thermoplastic Elastomers – – $410 $80 $30 17 $520 Advanced Composites – – $100 $40 – 8 $140 Specialty Vinyl Formulations – – $25 $75 – 13 $100 Total Addressable Market ($ millions) – – $1,230 $1,170 $440 $2,840 12% 38% 2006 2017 $20 $52 2006 2017 Research & Development Spend ($ millions) Vitality Index % of sales from products launched last 5 years I N N O V A T I O N D R I V E S E A R N I N G S G R O W T H PolyOne Corporation 32 A U N I Q U E C U S T O M E R E X P E R I E N C E Industrial Design IQ DESIGN LABS PolyOne Corporation 33 Material & Color Expertise Manufacturing Expertise 3 14 2014 2017 Industrial designers $0 $7M 2014 2017 $4M $40M 2014 2017 Opportunity funnel New business revenue 3 D P R I N T I N G B R I N G I N G N E W I D E A S T O L I F E PolyOne Corporation 34 Enables validation of fit and function Shortens design cycle and time to market Avoids tooling rework Drives innovation Delivers substantial customer value LSS CUSTOMER FIRST PolyOne Corporation 35 Customer Projects Enables sales growth by building more intimate customer relationships, giving us insight to customers’ needs, with a service that is not easily replicated 2014 2017 2 85 Lead Specialists T H E E V O L V I N G C U S T O M E R R E L A T I O N S H I P PolyOne Corporation 36 Expanded Path Traditional Path Strategic Accounts/ Field Sales Business Development Customer Service Web and Social Media Inside Sales PolyOne Corporation 37 Investments in digital and dedicated inside sales to improve customer experience 80% increase in leads (from 6,000 to 11,000) driven by website, phone, and online chat EXPANDED PATH A D D I N G C U S T O M E R T O U C H P O I N T S 4 21 2014 2017 Inside sellers $11M $88M 2014 2017 Inside sales/digital revenue C O M M E R C I A L R E S O U R C E S I N N O V A T I O N S E R V I C E I N S P I R E D F U T U R E 6-8% annual increase in commercial resources 4 focused end-markets aligned with global megatrends 5 strategic innovation platforms 30% increase in IQ Design projects 35% increase in revenue from inside sales/digital ≥35% vitality index PolyOne Corporation 38 I N N O V A T I N G W I T H P O L Y O N E PolyOne Corporation 39 SEGMENT REVIEWS POLYONE DISTRIBUTION PolyOne Corporation 40 S C O T T H O R N D I S T R I B U T I O N E N D M A R K E T S & S U P P L I E R S PolyOne Corporation 41 Transportation 23% Healthcare 22% Industrial 18% Consumer 15% Appliance 7% Electrical & Electronics 6% Building & Construction 4% Packaging 3% Wire & Cable 2% $20 $25 $63 $73 2.9% 4.0% 5.9% 6.3% 0.0% 1.0% 2.0% 3.0% 4.0% 5.0% 6.0% 7.0% 15 25 35 45 55 65 75 2005 2009 2013 2017 Operating Income & Margin2017 Revenue | $1.2 Billion http://www.polyone.com/Pages/VariationRoot.aspx http://www.polyone.com/Pages/VariationRoot.aspx S E R V I C E I S O U R B U S I N E S S PolyOne Corporation 42 Uniquely positioned to help our customers grow their brand and value-added solutions 1.2B $ Annual Sales 250 Global Employees 24 Strategic Presence 132 Sales Reps Warehouse Locations 6 Service Centers Dedicated Commercial Team S E R V I C E I S O U R B U S I N E S S S A F E L Y A N D R E S P O N S I B L Y PolyOne Corporation 43 95% on-time delivery Customer/Product Combinations 14,000 Transactions/Month In-Person Customer Visits 6,500 27,000 $ K E Y C O M M E R C I A L I N V E S T M E N T S PolyOne Corporation 44 Generating opportunities 37% more sales calls $65M in new revenue from inside sales $400M increase in new opportunities Enhancing efficiency 24% increase in close rate 51% increase in prospecting calls Increased commercial headcount 119 13211 1315 23 2014 Q1 2018 Sales R&D / Technical Marketing + 18% + 53% + 11% PolyOne Corporation 45 Providing differentiated services that meet the needs of the changing customer landscape G R O W T H T H R O U G H I N S I D E S A L E S $4 $65 2014 2017 PolyOne Distribution Inside Sales $ in millions PolyOne Corporation 46 G R O W T H T H R O U G H M U L T I P L E S A L E S C H A N N E L S Technical Field Sales Key Accounts / Industry Sales Inside Sales Serving a broad spectrum of customers Leveraging digital systems to drive awareness and enhance the customer experience N E W R E S O U R C E S F U E L I N G T H E F U T U R E PolyOne Corporation 47 P O D S A L E S F U N N E L +27% 2014 $1.2 billion 2017 $1.6 billion C O M M E R C I A L R E S O U R C E S I N N O V A T I O N S E R V I C E I N S P I R E D F U T U R E 6-8% annual increase in commercial resources >10% annual increase in revenue from inside sales and digital with expanded customer touch points 8% annual expansion of sales funnel with best-in-class service and technical expertise 6-8% compound annual operating income growth 6-7% operating margins PolyOne Corporation 48 SPECIALTY ENGINEERED MATERIALS PolyOne Corporation 49 M I C H A E L G A R R A T T S P E C I A L T Y E N G I N E E R E D M A T E R I A L S E N D M A R K E T S & S O L U T I O N S PolyOne Corporation 50 Engineered Formulations Advanced Composites Thermoplastic Elastomers Consumer 20% Transportation 19% Electrical & Electronics 15% Wire & Cable 13% Healthcare 11% Industrial 8% Packaging 7% Appliance 4% Building & Construction 3% S P E C I A L T Y E N G I N E E R E D M A T E R I A L S Revenue by Region Operating Income & Margin 2 0 1 7 R E V E N U E | $ 6 2 4 M I L L I O N PolyOne Corporation 51 $21 $57 $76 0.1% 5.1% 9.3% 12.1% 0.0% 2.0% 4.0% 6.0% 8.0% 10.0% 12.0% 14.0% 20 30 40 50 60 70 80 90 2005 2009 2013 2017 Europe 28% United States 48% Asia 22% Canada 2% C A P I T A L I Z I N G O N T H E G L O B A L M A R K E T PolyOne Corporation 52 Demand for engineered materials is accelerating Expanding thermoplastic elastomer portfolio to meet the demands of local consumption Grow and develop low smoke, non-halogen technologies to meet increasing European standards Adding capacity in strategic markets India Germany China North America Establishing a commercial hub in Southeast Asia C O M M E R C I A L R E S O U R C E S I N N O V A T I O NS E R V I C E S T R A T E G I C I N V E S T M E N T I N 3 K E Y A R E A S PolyOne Corporation 53 K E Y C O M M E R C I A L I N V E S T M E N T S PolyOne Corporation 54 Generating opportunities 13% more sales calls 36% increase in customization projects $270M increase in new opportunities Enhancing efficiency 12% reduction in average territory size, enabling greater customer focus 50% improvement in speed of formulation turnaround Increased commercial headcount 133 17335 39 120 147 2014 Q1 2018 R&D / Technical Marketing Sales + 30% + 11% + 23% N E W R E S O U R C E S F U E L I N G T H E F U T U R E PolyOne Corporation 55 S E M S A L E S F U N N E L +43% 2014 $610 million 2017 $880 million L S S C U S T O M E R F I R S T G R O W T H T H R O U G H S E R V I C E PolyOne Corporation 56 Leading Sporting Goods Manufacturer Provided Lean Six Sigma training and led an onsite Black Belt project to improve product development cycle times Reduced innovation project cycle times by over 10% and prototyping by 40% 80% increased production resulting in $500k savings I N N O V A T I O N S P O T L I G H T : C O M P O S I T E S PolyOne Corporation 57 C O M P O S I T E S R E F R E S H E R PolyOne Corporation 58 Fiber Polymer Composite Strength Design Flexibility Continuous Fiber Thermoset Composites Short Glass Fiber Thermoplastics Continuous Fiber Thermoplastic Composites Long Glass Fiber Thermoplastics S T R A T E G I C I N V E S T M E N T H I S T O R Y PolyOne Corporation 59 Acquired Polystrand Installed LFT production Avon Lake Long Fiber Thermoplastic (LFT) Technology Installed LFT production Barbastro, Spain Acquired Glasforms Acquired Gordon Composites Thermoplastic Composites Long Fiber Reinforced Thermoplastics Continuous Fiber Thermosets 2010 2012 2015 2016 20162009 20122011 2014 C O M P O S I T E S I N T R A N S P O R T A T I O N PolyOne Corporation 60 W A T E R C R A F TR A I L H E A V Y T R U C K Bulkheads and Transoms Ceilings and Hatches Doors and Cabinetry Flooring Door Panels Side Walls Flooring & Side Panels Aerodynamic Fairings Seat and Bunk Reinforcements 17 44 At Acquisition Now Commercial Resources 0% 20% At Acquisition Goal Operating Margins Test Market Innovation Projects 8 PolyOne Corporation 61 A D V A N C E D C O M P O S I T E S Long-term investments align with key global megatrends Light-Weighting Design Flexibility Sustainability C O M M E R C I A L R E S O U R C E S I N N O V A T I O N S E R V I C E I N S P I R E D F U T U R E 6-8% annual increase in commercial resources >10% annual increase in customization projects 10% annual expansion of sales funnel, enhancing portfolio in 4 focus end markets 20% increase in global capacity 12-15% compound annual operating income growth 14-16% operating margins PolyOne Corporation 62 PERFORMANCE PRODUCTS & SOLUTIONS PolyOne Corporation 63 D O N W I S E M A N P E R F O R M A N C E P R O D U C T S & S O L U T I O N S E N D M A R K E T S & S O L U T I O N S PolyOne Corporation 64 Specialty Vinyl Solutions Healthcare Formulations Smart Device Materials Flame Retardant Polymers Building & Construction 30% Industrial 18% Transportation 16% Wire & Cable 15% Appliance 7% Packaging 5% Consumer 5% Electrical & Electronics 3% Healthcare 1% Asia 2% United States 77% Mexico 5% Canada 16% P E R F O R M A N C E P R O D U C T S & S O L U T I O N S Operating Income & MarginRevenue by Region 2 0 1 7 R E V E N U E | $ 7 2 1 M I L L I O N $40 $33 $56 $77 4.6% 3.6% 7.2% 10.7% 0.0% 2.0% 4.0% 6.0% 8.0% 10.0% 12.0% 14.0% 16.0% 0 10 20 30 40 50 60 70 80 90 100 2005 2009 2013 2017 PolyOne Corporation 65 $886 $668 $773 $721Sales C O M M E R C I A L R E S O U R C E S I N N O V A T I O NS E R V I C E S T R A T E G I C I N V E S T M E N T I N 3 K E Y A R E A S PolyOne Corporation 66 K E Y C O M M E R C I A L I N V E S T M E N T S PolyOne Corporation 67 Generating opportunities 25% more sales calls 113% increase in innovation pipeline $240M increase in new opportunities Enhancing efficiency 36% increase in prospecting calls 300 basis point improvement in operating margin Increased commercial headcount 57 66 17 18 37 53 2014 Q1 2018 R&D / Technical Marketing Sales + 16% + 43% + 6% N E W R E S O U R C E S F U E L I N G T H E F U T U R E PolyOne Corporation 68 P P & S S A L E S F U N N E L +40% 2014 $610 million 2017 $850 million L S S C U S T O M E R F I R S T G R O W T H T H R O U G H S E R V I C E PolyOne Corporation 69 Leading Wire & Cable Manufacturer Provided Lean Six Sigma training and led on-site Kaizen process improvements Reduced over 400 labor hours through reorganized work area and floor space Increased manufacturing throughput value $1.4M G R O W T H T H R O U G H S E R V I C E PolyOne Corporation 70 IQ Design is collaborating with a leading medical device manufacturer to replace metal and provide chemical resistance to solve cracking issues related to intense cleaning requirements H E A L T H C A R E I N N O V A T I O N S I N N O V A T I O N S P O T L I G H T : F L A M E R E T A R D A N T P O L Y M E R S PolyOne Corporation 71 F L A M E R E T A R D A N T D R I V E R S PolyOne Corporation 72 Shift toward less toxic solutions Increased consumer awareness Focus on environmentally friendly solutions New regulatory standards F L A M E R E T A R D A N T P E R F O R M A N C E S P E C T R U M PolyOne Corporation 73 Flame Retardant Flame Retardant Flame Retardant Non-Halogen No Dripping Low Smoke Low Toxicity & Corrosiveness H A L O G E N N O N - H A L O G E N L S F O H ( L o w S m o k e a n d F u m e , N o n - H a l o g e n ) Non-Halogen R E G U L A T O R Y C H A N G E S P R O V I D E O P P O R T U N I T Y L E D S O L U T I O N S PolyOne Corporation 74 Solutions for rigid molded & extruded applications Superior outdoor weather performance Excellent light dispersion qualities Formulated to meet stringent flame-rating regulations Custom design support to meet demand C O M M E R C I A L R E S O U R C E S I N N O V A T I O N S E R V I C E I N S P I R E D F U T U R E 6-8% annual increase in commercial resources 8% more sales calls annually 10% annual expansion of sales funnel, including breakthroughs in healthcare technologies 8-10% compound annual operating income growth 12-14% operating margins PolyOne Corporation 75 COLOR ADDITIVES & INKS PolyOne Corporation 76 M A R K C R I S T C O L O R , A D D I T I V E S & I N K S E N D M A R K E T S & S O L U T I O N S PolyOne Corporation 77 Solid Colorants Performance Additives Screen Printing Inks Liquid Colorants Packaging 27% Industrial 14% Textiles 12% Building & Construction 10% Wire & Cable 10% Transportation 8% Consumer 7% Healthcare 6% Electrical & Electronics 3% Appliance 3% Operating Income & MarginRevenue by Region C O L O R , A D D I T I V E S & I N K S 2 0 1 7 R E V E N U E | $ 8 9 3 M I L L I O N $4 $25 $104 $139 0.9% 5.5% 12.2% 15.5% 0.0% 2.0% 4.0% 6.0% 8.0% 10.0% 12.0% 14.0% 16.0% 18.0% 20 30 40 50 60 70 80 90 100 110 120 130 140 150 2005 2009 2013 2017 PolyOne Corporation 78 Europe 32% United States 46% Asia 15% Canada 1% Mexico 4% Brazil 2% C A P I T A L I Z I N G O N T H E G L O B A L M A R K E T PolyOne Corporation 79 Emerging markets driving strong demand for color and additives Rapid adoption of food and beverage packaging additives Fiber colorants growth focused on expanding Asia-Pacific market Increase commercial investments focused on China, India and Mexico Expand capacity in China and leverage investments in India Recent acquisitions increasing global reach C O M M E R C I A L R E S O U R C E S I N N O V A T I O NS E R V I C E S T R A T E G I C I N V E S T M E N T I N 3 K E Y A R E A S PolyOne Corporation 80 K E Y C O M M E R C I A L I N V E S T M E N T S PolyOne Corporation 81 Generating opportunities 35% more sales calls 30% increase in customized color formulations 106% increase in innovation pipeline $170M increase in new opportunities Enhancing efficiency 20% increase in prospecting calls 9 days or less in design turnaround time: best-in-class Increased commercial investment 301 382 38 43 209 275 2014 Q1 2018 R&D / Technical Marketing Sales + 27% + 13% + 32% N E W R E S O U R C E S F U E L I N G T H E F U T U R E PolyOne Corporation 82 C A I S A L E S F U N N E L +32% 2014 $540 million 2017 $710 million L S S C U S T O M E R F I R S T PolyOne Corporation 83 Developed inventory management framework to reduce working capital by 20% Printing Equipment and Supply Manufacturer Provided Lean Six Sigma training and conducted process mapping exercises to identify key improvement opportunities Optimize manufacturing: 45% improvement in assembly process, 25% improvement in cycle time G R O W T H T H R O U G H S E R V I C E I N N O V A T I O N S P O T L I G H T : A D D I T I V E & C O L O R A N T T E C H N O L O G I E S PolyOne Corporation 84 B A R R I E R T E C H N O L O G I E S Active oxygen scavenging additive in the bottle wall Evolving technology for active oxygen scavenging additive in the bottle cap Amosorb™ HyGuard™ UV and visible light blocking additive to prevent degradation of product Lactra™ SX Market leader in oxygen, light and UV barrier solutions for the PET bottle market PolyOne Corporation 85 S T R A T E G I C A D D R E S S A B L E M A R K E T > $ 2 0 0 M F I B E R C O L O R A N T S Eliminate waste water associated with conventional dyeing Help meet sustainability targets for brand owners Enable “uncolored fiber” producers to bypass dyehouse Strategic addressable market >$300M PolyOne Corporation 86 S T R A T E G I C I N V E S T M E N T H I S T O R Y PolyOne Corporation 87 Thermoplastic Composites 2011 2015 2018 Acquired ColorMatrix Acquired Magenta Acquired IQAP $10 $45 2014 2017 Revenue from Fiber Color ($ in millions) Invested in development of liquid fiber colorant technology Expanded solid colorant offerings 38 43 At Acquisition Now Commercial Resources Innovation Projects 5 PolyOne Corporation 88 I N V E S T I N G F O R T H E F U T U R E Nearly 900 projects identified Gaining sustainable momentum & building trust with consumers Fiber Sales Funnel $125M “We are unleashing the power of human potential, all to advance the game. Senior management believes these measures are useful to investors because they allow for comparison to PolyOne's performance in prior periods without the effect of items that, by their nature, tend to obscure PolyOne's operating results due to the potential variability across periods based on timing, frequency and magnitude.

In the event of a conflict between this Quality Commitment and any mutually agreed specifications or quality agreement that is executed by NEU, the mutually agreed specifications or signed quality document shall control. 1.0 PRODUCT DESCRIPTION Thermoplastic material in pellet form. 2.0 TEST METHODS NEU test methods are modeled after ASTM testing standards, where applicable. 3.0 OPERATIONAL DEFINTIONS 3.1 Lot (Batch): Material manufactured at one time. 3.2 Blend: No more than three lots of a specific raw material, combined together to form a homogeneous mixture. 3.2.1 Full lot tractability of non-proprietary formulations will be reflected on the COC 3.3 Certification: “Certificate of Conformance” or “Certificate of Analysis” based material requirements 3.4 Certificate of Analysis: Document containing information that the product conforms to the established Product Specifications. 3.5 Certificate of Conformance: Document containing confirmation that the product conforms to the defined formulation. 3.6 Finished Product Form: Finished product shape (Cylindrical, Spherical) 3.7 Product Specification: the product specifications that are contained in a written document signed by NEU, or if such document does not exist, the Certificate of Analysis or Certificate of Conformance issued by NEU. 4.0 PACKAGING 4.1 Standard product packaging options include: 4.1.1 Drum 4.1.2 Gaylord 4.1.3 Pail 4.1.4 Individual bag in box Approved Plant/Local : Reference Document Document #: DOC-10815 Revision: 3 Document Owners: Dean Clark Effective Date: Oct 29, 2020 Title: NEU Quality Commitment Page 2 of 4 Only the electronic version of this document in ETQ is the controlled version of the document. This document is property of Avient Corporation and may not be reproduced or communicated to third parties without authorization. 4.1.5 Packaging may include a liner or pallet based on the configuration.

Please note that material properties may vary based on factors such as color and processing conditions. Please note that material properties may vary based on factors such as color and processing conditions.