RAPID OXYGEN GREEN CMPD The search is NOT CASE SENSITIVE.

Filler Yarns/Core Fillers (not visible) • PET, Polyester, Kevlar yarns coated with Swellcoat (absorbs and blocks water) 7. Binder • PET, Polyester, Kevlar yarns coated with Swellcoat (absorbs and blocks water) 2 3 4 5 7 6 8 9. Buffer thread (inside tubes) • PET, Polyester, Kevlar yarns coated with Swellcoat (absorbs and blocks water) 8.

For use in elastomers in the production of pressure-sensitive adhesives, mastics and sealants based on styrene-butadiene rubber where color and heat stability are not critical. Used in hot melt adhesives and high pressure sensitive adhesives. Used in hot melt adhesives and high pressure sensitive adhesives.

In the initial stage, we generally do not require what is considered sensitive personal information or “special categories of personal data” under applicable privacy laws (referred to in this Notice as “sensitive personal information”). Sensitive personal information refers to data that reveals an individual’s racial or ethnic origin, political opinions, religious or philosophical beliefs, or trade union membership, genetic data, biometric data, or data concerning health or data concerning a person’s sex life or sexual orientation. Do not send us sensitive personal information to us via email.

These types of gates are usually used when materials are shear sensitive, because the gates are larger and thus create less shear. A larger processing window will account for the lot to lot changes between materials, without having to make process changes.3 Setting the Beginning Variables • Injection Pressure = Maximum of machine - Should not be pressure limited • Injection Velocity = Maximum of machine - This is for the injection velocity curve starting point - If flashing is an issue start slower and then increase • Injection Cut-Off Time = 15 seconds - This is only a limiting factor, needs to be above 10 seconds for velocity graph • Hold Pressure = 0 - Need to get 95% full part with a hold pressure of 0 • Hold Time = 10-15 seconds - Need to ensure gate is frozen • Screw Speed = 90% of Maximum - Unless shear sensitive material, if shear sensitive, set RPMs to optimum • Cooling Time = 10–15 seconds • Shot Size = 50% of calculated part volume • Decompression = .25" • Transfer Position = High enough to ensure a cushion - Cushion size does not matter but there must be a cushion to keep a constant pressure on the melt during hold time - Typically 0.25" is sufficient • Back Pressure = 800-1000 plastic pressure - 100–150 hydraulic pressure - Unless specified by material data sheet Determining Shot Size The shot size should be determined by calculating the combined volume of the parts and the runner system. Ejector pins may push into the part, or may warp and deflect the part Determination of Optimum Injection Velocity 0.00 0.50 1.00 1.50 2.00 Relative Shear Rate, 1/sec 40000 35000 30000 25000 20000 15000 10000 5000 0 FIGURE 48 - Viscosity vs Shear Rate Curve Design Guide 23 • The screw recovery is dictated by how shear- sensitive the material is; if the material is not shear-sensitive the screw recovery RPMs should be set at 90% of maximum.

Overview and key benefits for shelf life extender oxygen scavenging additive

MARKETS AND APPLICATIONS • Cable jackets for low and medium-voltage power cables with metal armoring, typically installed underground or where installation requires them to be bent • Armored cable applications that require compliance with LTS1 requirements as per the BS 7655-6.1 standard IMPACT • High environmental stress cracking resistance • High tear strength and elongation at break at temperatures ranging from -25°C to 90°C • Flame retardant performance • Limiting oxygen index (LOI) of 36% • Exceeds BS 7655-6.1:1997 standard criteria for LTS1–LTS4 for complex designs and armored cables PRODUCT BULLETIN Cable jacket liable to cracking Power Cable Cross Section Metal armoring 1.844.4AVIENT www.avient.com Copyright © 2023, Avient Corporation. KEY CHARACTERISTICS ECCOH 5924 FORMULATION ECCOH 5981 FORMULATION ECCOH 5983 UV FORMULATION Material Standards BS7655-6, 1 (LTS1–4), BS6724, IEC 60502 BS7655-6, 1 (LTS3) BS7655-6, 1 (LTS1–4) Tear Strength at 23°C 7.7 N/mm 10 N/mm 11 N/mm Tear Strength at 65°C 2.3 N/mm 5 N/mm 6.5 N/mm Hot Pressure Test (6h at 90°C) 39% –

PET Bottle for Hair Care Pressure-sensitive Switch Mats Pet Care & Supplies

PG 303257.00 RD PET PG 303258.00 BU PET The search is NOT CASE SENSITIVE.

Avient Introduces ColorMatrix™ Amosorb™ Oxyloop™: A New Oxygen Scavenging Additive to Enhance Recyclability...