The resins have bio-based content up to 95 percent, as calculated to ASTM D6866 standard.

These new grades contain 35 to 75 percent bio content, validated using ASTM C6866-21 method B.

Glass fiber reinforced polymer (GFRP) dowel bars offer advantages over traditional steel or epoxy- coated steel bars: • Electromagnetic transparency: ideal for high- speed toll roads to prevent interference • Corrosion resistance: the GFRP material will not rust or corrode in salt or alkaline environments • Light weight: less than one-third the weight of steel • Does not bond to concrete: eliminates the need for sleeves or grease to allow for expansion and contraction Glasforms™ composite dowel bars are tested and approved to meet the following requirements: • ASTM 1356 Glass Transition Temperature • ASTM D570 Water Absorption • ASTM 2344 Short Beam Strength • ASTM 7617 Transverse Shear Strength Glasforms™ Composite Dowel Bars for Concrete Pavement Construction APPLICATION OVERVIEW WHY GLASFORMS PULTRUDED COMPOSITES? Matrix Resin Fiber Reinforcement Fiber Content, by Weight (%) Epoxy E-CR or E-Glass >70% MATERIAL TECHNICAL DATA Property Test Procedure Rod Diameter 1.25 in (31.75 mm) 1.50 in (38.10 mm) Glass Transition Temp (Tg) ASTM 1356 100°C Minimum 100°C Minimum Water Absorption 24 hours at 50°C (122°F) ASTM D570 0.03% 0.03% Short Beam Strength (ILSS) ASTM 2344 8,400 psi (58 MPa) 9,200 psi (64 MPa) Transverse Shear Strength ASTM 7617 23,400 psi (160 MPa) 24,640 psi (170 MPa) Traceability Lot number shall be clearly marked on each package/shipment. TYPICAL PROPERTIES Tensile Strength Tensile Modulus Flexural Strength Compressive Strength ASTM D3916 ASTM D3916 ASTM D790 ASTM D695 110 ksi (760 N/mm²) 6.0 psi x 106 (41 kN/mm²) 130 ksi (900 N/mm²) 85 ksi (590 N/mm²) TYPICAL EQUIVALENT MECHANICAL PERFORMANCE*

TECHNICAL PROPERTIES(1) TEST METHOD Edgetek™ ET8900-0011 HI UV NAT Edgetek™ ET8900-0012 HI UV White Edgetek™ ET8900-0013 HI UV Black Physical Density/Specific Gravity ASTM D792 1.13 g/cm3 1.15 g/cm3 1.13 g/cm3 Molding Shrinkage - Flow ASTM D955 1.4–2% 1.4–2% 1.4–2% Mechanical Tensile Strength (Yield) ASTM D638 5,900 psi 5,800 psi 5,800 psi Tensile Modulus(2) ASTM D638 169,000 psi 161,087 psi 176,000 psi Flexural Modulus(3) ASTM D790 187,000 psi 190,985 psi 188,000 psi Impact Notched Izod Impact 73°F (23°C), 0.125 in ASTM D256A 17.3 ft-lb/in 16.5 ft-lb/in 16.5 ft-lb/in Notched Izod Impact -22°F (-30°C), 0.125 in ASTM D256A 3.2 ft-lb/in 3.0 ft-lb/in 3.3 ft-lb/in Thermal (HDT) 66 psi (0.45 MPa), 0.125 in ASTM D648 121°C 135°C 129°C NORTH AMERICA GRADES (1) Data based on single lot of lab generated samples.

TECHNICAL BULLETIN 1.844.4AVIENT www.avient.com PROPERTY TEST METHOD UNITS VERSAFLEX ™ CE 3130-80N VERSAFLEX™ CE 3130-70N Shore Hardness ASTM D2240 Shore A 79 69 Specific Gravity ASTM D792 g/cm3 1.08 1.04 Tensile Strength ASTM D412 psi 2,484 2,222 Melting Flow Index (190°C, 21.6kg) ASTM D1238 g/10min 5.2 4.4 Elongation ASTM D412 % 864 667 Flexural Modulus @ 300% ASTM D790 psi 975 855 Viscosity @ 11,170 sec, 200°C ASTM D3835 Pa.s 30.6 22.2 Abrasion (Mass Lost) ASTM D3389 mg 1.1 2.6 UV Resistance 0.68W/m 2 45°C 168hours — Good Good Stain Resistance *Condition 1*Condition 2 — Excellent Excellent Blooming 85% RH30°C,168 hours — Non Non Processing (Demold) — — Excellent Good Cycle Time — — Short Middle Overmold Substrate — — PC/ABS PC/ABS KEY PROPERTIES AND OVERMOLD PERFORMANCE Copyright © 2021, Avient Corporation. UV Resistance Test - 0.68W/m2 @ 45°C expose 168 hours Anti-abrasion Test - H18 wheel load 1kg @ 500 cycles Surface/Non-blooming - Visual observation Touch Feel - Hand touch Mechanical Properties - Refer to hardness, gravity, tensile strength, elongation, MFI, and flexural modulus, which are tested using ASTM methods Processing - Demold speed & cycle time TEST RESULTS Comprehensively, the Versaflex CE 3130 non-blooming series performed better than competitive materials in balancing functional properties and processing.

This product selection guide provides detailed information to help you select the Maxxam product that’s right for your application. 4 INJECTION MOLDING POLYPROPYLENE Product Code - - - PP5113 B44 F5134T2-4 PP5130 B63 F5134T4-1 Filler Percentage - % - 13 20 30 40 Tensile Strength Yield psi ASTM D638 5000 4800 4600 4500 MPa ISO 527 33 33 32 31 Tensile Elongation Yield % ASTM D638 6 4 3 2 ISO 527 Break % ASTM D638 60 30 15 10 ISO 527 Flexural Modulus 73°F (23°C) psi ASTM D790 300,000 360,000 400,000 460,000 MPa ISO 178 2300 2450 2900 3300 Notched Izod Impact 73°F (23°C) ft-lb/in ASTM D256 0.65 0.60 0.55 0.50 kJ/m2 ISO 180 3.50 3.3 3.00 2.75 Heat Deflection 66 psi °F ASTM D648 230 240 260 275 °C ISO 75 110 116 127 135 264 psi °F ASTM D648 130 140 150 175 °C ISO 75 54 60 66 79 Specific Gravity 73°F (23°C) - ASTM D792 0.99 1.04 1.15 1.25 ISO 1183 Linear Shrinkage Range 1/8 in wall % - 1.2–1.6 1.0–1.4 0.8–1.2 0.6–1.0 3.2 mm wall % - 1.2–1.6 1.0–1.4 0.8–1.2 0.6–1.0 Product Code - - - PP6113 A77-SM PP6120 B16-2 PP6130 B11 PP6135 B40-UV Filler Percentage - % - 13 20 30 35 Tensile Strength Yield psi ASTM D638 4350 3500 2600 3700 MPa ISO 527 30 24 18 26 Tensile Elongation Yield % ASTM D638 5 4 7 6 ISO 527 Break % ASTM D638 35 70 150 70 ISO 527 Flexural Modulus 73°F (23°C) psi ASTM D790 290,000 280,000 280,000 390,000 MPa ISO 178 2000 1950 1750 2700 Notched Izod Impact 73°F (23°C) ft-lb/in ASTM D256 0.7 2.7 4.5 0.65 kJ/m2 ISO 180 4.0 14 24 3.5 Heat Deflection 66 psi °F ASTM D648 239 215 225 250 °C ISO 75 115 102 107 123 264 psi °F ASTM D648 140 125 130 150 °C ISO 75 60 52 54 60 Specific Gravity 73°F (23°C) - ASTM D792 0.99 1.05 1.15 1.18 ISO 1183 Linear Shrinkage Range 1/8 in wall % - 1.1–1.5 .9–1.3 0.7–1.1 0.5–0.9 3.2 mm wall % - 1.1–1.5 .9–1.3 0.7–1.1 0.5–0.9 Maxxam™ Talc-Filled Copolymer Polypropylene • Scratch & mar resistant • UL approved • FDA certifiable • Natural, black or colors • High flow grades • UV stabilized • UL approved • FDA certifiable • Natural, black or colors • High flow grades • UV stabilized • Recycled content Maxxam™ Talc-Filled Homopolymer Polypropylene Offers a moderate level of impact strength and improved stiffness and heat deflection performance. PROPERTY CONDITION UNITS METHOD PRODUCT EXAMPLES 51.866.POLYONE www.polyone.com INJECTION MOLDING POLYPROPYLENE Product Code - - - PP5210A111 PP5220F A1 PP5230F B1 PP5240 A111 Filler Percentage - % - 10 20 30 40 Tensile Strength Yield psi ASTM D638 4600 4300 3900 3500 MPa ISO 527 32 30 27 24 Tensile Elongation Yield % ASTM D638 7.0 6.0 5.5 5.0 ISO 527 Break % ASTM D638 125 115 100 70 ISO 527 Flexural Modulus 73°F (23°C) psi ASTM D790 250,000 285,000 310,000 340,000 MPa ISO 180 1600 1900 2100 2300 Notched Izod Impact 73°F (23°C) ft-lb/in ASTM D256 0.70 0.70 0.70 0.70 kJ/m2 ISO 180 3.85 3.85 3.85 3.85 Heat Deflection 66 psi °F ASTM D648 190 210 225 240 °C ISO 75 88 99 107 116 264 psi °F ASTM D648 120 125 130 133 °C ISO 75 49 52 54 56 Specific Gravity 73°F (23°C) - ASTM D792 0.96 1.04 1.15 1.25 Linear Shrinkage Range 1/8 in wall % - 1.3–1.7 1.1–1.5 0.9–1.3 0.7–1.1 3.2 mm wall % - 1.3–1.7 1.1–1.5 0.9–1.3 0.7–1.1 Product Code - - - PP6210 A11 PP7220 A614 PP6230F A1 PP6240 A44 Filler Percentage - % - 10 20 30 40 Tensile Strength Yield psi ASTM D638 3200 3400 2800 2550 MPa ISO 527 22 24 19 18 Tensile Elongation Yield % ASTM D638 14.0 10.0 8.0 7.0 ISO 527 Break % ASTM D638 >400 >400 >400 200 ISO 527 Flexural Modulus 73°F (23°C) psi ASTM D790 160,000 185,000 250,000 225,000 MPa ISO 178 1100 1300 1750 1550 Notched Izod Impact 73°F (23°C) ft-lb/in ASTM D256 >10.0 >10.0 8 8.0 kJ/m2 ISO 180 55.0 55.0 44.0 14.0 Heat Deflection 66 psi °F ASTM D648 160 170 198 200 °C ISO 75 71 77 92 93 264 psi °F ASTM D648 100 105 108 112 °C ISO 75 38 41 42 44 Specific Gravity 73°F (23°C) - ASTM D792 0.96 1.04 1.15 1.25 ISO 1183 Linear Shrinkage Range 1/8 in wall % - 1.2–1.6 1.0–1.4 0.8–1.2 0.6–1.0 3.2 mm wall % - 1.2–1.6 1.0–1.4 0.8–1.2 0.6–1.0 Maxxam™ Calcium Carbonate Filled Homopolymer Polypropylene Maxxam™ Calcium Carbonate Filled Copolymer Polypropylene Offers improved stiffness over unfilled materials as well as substantial improvement in drop weight impact and notched izod impact. FDA certifiable • Natural, black or colors • UV stabilized Product Code - - - PE4125 B1 Reinforcement Type - - - Talc Reinforcement % - % - 25 Specific Gravity 73°F (23°C) - ASTM D792 1.15 ISO 1183 Tensile Strength Yield psi ASTM D638 4050 MPa ISO 527 28 Tensile Elongation Yield % ASTM D638 10 ISO 527 Break % ASTM D638 40 ISO 527 Flexural Modulus 73°F (23°C) psi ASTM D790 270,000 MPa ISO 178 1850 Notched Izod Impact 73°F (23°C) ft-lb/in ASTM D256 3.5 kJ/m2 ISO 180 20.0 Heat Deflection 66 psi °F ASTM D648 190 °C ISO 75 88 264 psi °F ASTM D648 115 °C ISO 75 46 PROPERTY CONDITION UNITS METHOD PRODUCT EXAMPLES 12 www.polyone.com Copyright © 2019, PolyOne Corporation.

PRODUCT BULLETIN PROPERTY TEST METHOD TYPICAL VALUE (ENGLISH) TYPICAL VALUE (SI) Specific Gravity ASTM D-792 11.0 11.0 Tensile Modulus1 ASTM D-638 1.20E+6 psi 8270 MPa Tensile Strength1 (Yield) ASTM D-638 3,950 psi 27.2 MPa Flexural Modulus ASTM D-790 800,000 psi 5520 MPa Flexural Strength ASTM D-790 7,000 psi 48.3 MPa Notched Izod Impact2 ASTM D-256A 2.1 ft•lb/in 110 J/m Deflection Temperature Under Load 66 psi (0.45 MPa), Unannealed, 0.250 in (6.35mm) ASTM D-648 280°F 138°C Deflection Temperature Under Load 264 psi (1.8 MPa), Unannealed, 0.250 in (6.35mm) ASTM D-648 190°F 87.8°C TECHNICAL PROPERTIES 1 Type I, 0.20 in/min (5.1 mm/min) 2 73°F (23°C), 0.125 in (3.18 mm), Injection molded www.avient.com Copyright © 2020, Avient Corporation.

TECHNICAL BULLETIN Characteristics Artisan™ Nylon Solution Painted Metal Painted Plastic Traditional Molded-in Color Impact Modified Nylon PA Ionomer Alloy Aesthetic Very Good Excellent Excellent Good Very Good Very Good Scratch Appearance Excellent Poor Poor Good Excellent Excellent Scratch & Mar Resistance Very Good Excellent Excellent Poor Very Good Excellent Color Customization Good Excellent Excellent Very Good Good Good Stress Whitening Excellent Fair Fair Poor Excellent Excellent Weatherability Good Excellent Excellent Very Good Good Very Good Temperature Performance Good Excellent Fair Fair Fair Good Corrosion Resistance Excellent Fair Excellent Excellent Excellent Excellent Processability One Step Multi Step Multi Step One Step One Step Complex One Step Total Production Cost $$$ $$$$$ $$$$ $$ $$$ $$$$ Order Quantity Restrictions Some Some Some None More More COMPARISON OF NYLON, METAL, AND PLASTIC Properties Test Method Artisan™ AR6000-0007 HI UV* Gloss Level** Gloss reading at 60 degrees 80-93 Molding Shrinkage – Across Flow ASTM D955 0.009 to 0.013 in/in Tensile Strength (Yield) ASTM D638 7300 psi Tensile Strength (Break) ASTM D638 5300 psi Tensile Elongation (Yield) ASTM D638 6.0% Flexural Modulus ASTM D790 270500 psi Flexural Strength (Yield) ASTM D790 9950 psi Notched Izod Impact ASTM D256 -4°F (-20°C) 5 ft-lb/in 73°F (23°C) 11 ft-lb/in Unnotched Izod Impact ASTM D256 -4°F (-20°C) 29 ft-lb/in 73°F (23°C) 30 ft-lb/in Color & Aesthetics*** Green, medium blue, dark blue, red, orange, white, gray, black Color customization available based on specific needs KEY PROPERTIES Features: high-gloss finish, UV stability, scratch resistance, chemical/corrosion resistance, cold temperature impact resistance, heat resistance * Reflects average of several colors, properties shift slightly depending on color ** Gloss level varies based on tooling temperature *** UV data available upon request Copyright © 2023, Avient Corporation.

No. 0562.01) Revised 05/31/2022 Page 1 of 1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017 AVIENT CORPORATION 733 East Water Street North Baltimore, OH 45872 Claire Holman Phone: (419) 257-1327 MECHANICAL Valid To: October 31, 2023 Certificate Number: 0562.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following automotive plastics tests: Test Method: Test Name: ASTM D412 Tensile ASTM D523 Specular Gloss ASTM D618 (A) Conditioning of Plastics ASTM D624 (Die C) Tear Strength ASTM D638 Tensile Properties ASTM D792 (A) Density and Specific Gravity by Displacement ASTM D1004 Initial Tear Resistance ASTM D1203 (A) Volatile Loss ASTM D1895 (A) Apparent Density, Bulk Factor, Pourability ASTM D1921 Particle Size (Sieve Analysis) ASTM D2240 Durometer Hardness (Shore A and D) ASTM E1331 Color by Spectrophotometry Using Hemispherical Geometry FMVSS 571.302 Flammability FORD BN-102-01 (A) Low Temperature Flexibility FORD BO-131-03 Interior Odor ISO 3795 Determination of Burning Behavior of Interior Materials SAE J323 (A) Cold Cracking (Mandrel Bend) SAE J1351 Hot Odor for Insulation Materials SAE J1545 Instrumental Color Difference Measurement SAE J1756 Fogging Characteristics of Interior Automotive Materials (Photometric Only) DOC-058151 Angle of Repose 1 Laboratory Developed Method For the tests to which this accreditation applies, please refer to the laboratory’s Mechanical Scope of Accreditation.

This literature shall NOT operate as permission, recommendation, or inducement to practice any patented invention without permission of the patent owner. 1.844.4AVIENT www.avient.com TEST STANDARD UNIT SYNCURE™ XLPE S1054A ROHS NATURAL Specific Gravity ASTM D1505 – 0.919 Melt Flow Index, 190°C/2.16kg ASTM D1238 g/10min 1.045 Tensile Strength at Break ASTM D638 psi 2500 Tensile Elongation at Break ASTM D638 % 450 Delta Torque Internal g-m 2154 Moisture Content ASTM D2974 % 0.0004 Gel Content ASTM D2765 % 73 Hot Creep Elongation UL 2556 % 49 Hot Deformation UL 2556 % 6 TECHNICAL PROPERTIES *Gel Content, Hot Creep Elongation and Hot Deformation measured on 95 phr S1054A / 5 phr S100B system, and cured by autoclave for 9 hours