83285GNS ATHLETIC GOLD ACTION 83386SSV OLD GOLD 83391GNS ATHLETIC VEGAS GOLD

GOLD PEARL MONO 85100PEN RC GOLD 80010SSVFF ATHLETIC GOLD

ITS GOLD UV PE TURF GRASS GOLD PE UV HM GOLD P123C

87300GNS BRILLIANT GOLD 87720GNS OLD GOLD 4 88889MX GOLD

Standard grades in the portfolio conform to UL 94 V-2, V-0 and 5VA performance ratings, and many offer elevated Relative Thermal Index (RTI) ratings. Available in both halogen and non-halogen products, including grades with UL Yellow Card rating, Maxxam FR products can be customized for specific performance needs. Vents should be placed at the intersection of each 90° bend in the runner system off of the cold slug well and vented to atmosphere PROBLEM CAUSE SOLUTION Black Specks Contamination • Purge barrel with general purpose PP • Verify correct nozzle is being used • Pull screw for cleaning Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded-in stress Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed Insufficient packing • Increase hold pressure and time • Increase shot size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Troubleshooting Recommendations PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full • Increase shot size Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Troubleshooting Recommendations (continued) PROBLEM CAUSE SOLUTION Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Warp Process related • Increase cooling time • Increase melt temperature • Increase pack pressure • Increase pack time • Decrease mold temperature Mold design • Inspect for non-uniform mold cooling Part design • Inspect for non-uniform wall thickness Temperature control unit incorrect temperature • Check settings • Inspect thermocouple Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase injection rate • Increase mold temperature Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Increase melt temperature • Increase injection rate • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Processing Guide 5 Problem Cause Solution Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures• Decrease mold temperature Insufficient material volume • Increase shot size • Increase injection rate • Increase pack pressure/time • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Troubleshooting Recommendations 6 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Burning Melt and/or mold too cold • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents• Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection rate • Increase mold temperature Mold design • Decrease injection rate • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

Following the treatment period, the tensile bars for the control and treatment groups were tested within 48 hours using the ASTM D638 method at a rate of 2 in/min (50.8 mm/min), and the percent retention of tensile properties were determined relative to the respective control. Resistance ratings for Trilliant HC8900 series and competing materials against common healthcare disinfectants Resistance ratings for Edgetek ET8900 series and competing materials against common household cleaners and disinfectants.

Factors that could cause actual results to differ materially from those implied by these forward-looking statements include disruptions, uncertainty or volatility in the credit markets that could adversely impact the availability of credit already arranged and the availability and cost of credit in the future; the effect on foreign operations of currency fluctuations, tariffs and other political, economic and regulatory risks; the current and potential future impact of the COVID-19 pandemic on our business, results of operations, financial position or cash flows including without any limitation, any supply chain and logistics issues; the speed and strength of growth in the global 5G infrastructure market; our ability to achieve the strategic and other objectives relating to the acquisition of Clariant's Masterbatch business, including any expected synergies; changes in polymer consumption growth rates and laws and regulations regarding plastics in jurisdictions where we conduct business; fluctuations in raw material prices, quality and supply, and in energy prices and supply; production outages or material costs associated with scheduled or unscheduled maintenance programs; unanticipated developments that could occur with respect to contingencies such as litigation and environmental matters; an inability to achieve the anticipated financial benefit from initiatives related to acquisition and integration working capital reductions, cost reductions and employee productivity goals; our ability to pay regular quarterly cash dividends and the amounts and timing of any future dividends; information systems failures and cyberattacks; our ability to consummate and successfully integrate acquisitions; and amounts for cash and non-cash charges related to restructuring plans that may differ from original estimates, including because of timing changes associated with the underlying actions.

Microsoft Word - Avient Announces Registration Details for December 4th Investor Day _for Microsite 1 NEWS RELEASE FOR IMMEDIATE RELEASE Avient Announces Registration Details for December 4th Investor Day CLEVELAND – November 4, 2024 – Avient Corporation (NYSE: AVNT), a leading provider of specialized and sustainable materials solutions, will host an Investor Day for the investment community on Wednesday, December 4, 2024, beginning at 10:00 a.m.

Sep 25, 2024