AFNOR M 2 in France, DIN 4102 B 2–B 1 in Germany, UNI 8457–9174 C 1 in Italy, BKZ 5.2 in Switzerland, BS 5852.1990 CRIB 3–5 in UK)** • Standard portfolio available for PP injection molded applications APPLICATION BULLETIN * Laboratory weathering testing may not be determinative of all conditions of use; the end user must determine suitability of a product for its intended use ** Contact us for more information on regulatory compliance Copyright © 2022, Avient Corporation.

All products passed the OEKO-TEX® 100-2 standard, do not include plasticizers, and contain lower VOCs than traditional adhesive solutions. KEY CHARACTERISTICS • High-wearing comfort and elastic recovery • Strong and seamless adhesion to polyester and nylon fabrics • Passed OEKO-TEX 100-2 testing • Excellent washability at up to 60°C • Non-toxic formulations with low volatile organic compounds (VOC) and without added plasticizers • Attractive alternative to conventional TPU adhesive film and glue MARKETS & APPLICATIONS Versaflex TF Adhesive TPE solutions have been custom engineered for: • Elastic strips in underwear • Seam tapes in sports and fitness apparel PRODUCT BULLETIN 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

Ergonomic Grip Design Guide 1 Ergonomic Grip Design Guide 2 DEFINING THE USE CASE No single grip design is perfect for every product. To capture grip postures more accurately, you should observe and chart estimated joint angles in use, as shown in Figure 2. Mode 2 Eigenfrequencies in the forward-and-back motion.

TEL:+31(0)102922689. www.dnvgl.com/assurance Page 2 of 2 Appendix to Certificate PolyOne-Shanghai, China Locations included in the certification are as follows: Site Name Site Address Site Scope PolyOne Polymer (Tianjin) Company Limited No.28#C, Jin Bin Hi-Tech Industrial Park, 156 Nan Hai Road, Tianjin Economic-Technological, Tianjin, China, 300457 Manufacture of Masterbatch PolyOne-Shanghai, China No. 88, Guo Shou Jing Road, Z.

Zwolseweg 1, 2994 LB, Barendrecht, Netherlands - TEL: +31(0)102922689. www.dnv.com/assurance Page 2 of 2 Appendix to Certificate Polyone - Suzhou, China Locations included in the certification are as follows: Site Name Site Address Site Scope PolyOne Management (Shanghai) Co., Ltd.

Zwolseweg 1, 2994 LB, Barendrecht, Netherlands - TEL: +31(0)102922689. www.dnv.com/assurance Page 2 of 2 Appendix to Certificate PolyOne-Shanghai, China Locations included in the certification are as follows: Site Name Site Address Site Scope PolyOne Polymer (Tianjin) Company Limited No. 28#C, Jin Bin Hi-Tech Industrial Park, No. 156, Nan Hai Road, Tianjin Economic- Technological Development Area, Tianjin, China 300457 Manufacture of Colour and Additive Concentrates PolyOne-Shanghai, China No. 88, Guo Shou Jing Road, Z.

Nutritional components in dairy products are photosensitive, making them susceptible to light degradation • Light protection in dairy packaging helps maintain product integrity and extend shelf life A LIGHT BLOCKING SOLUTION THAT PROVIDES: • Light blocking and whiteness in PET dairy packaging • Protection from 2 weeks up to 12 months shelf life • Compatibility with monolayer and multilayer PET preforms • Full compatibility with rPET • Food contact approved (region dependent) • Low TiO₂ levels to increase recyclability, aligning with the emergence of white recycle streams PASTEURIZED MILK Typical shelf life 5–10 days WHITE COLOR LACTRA ESL LACTRA SX or LACTRA 4 EXTENDED SHELF LIFE MILK 2 weeks–3 months UHT MILK & PRODUCTS 4–12 months Lightweighting/CO2 reduction Reduced LDR – material & cost savings Improved processing performance BENEFITS OF COLORMATRIX™ LACTRA™ Improved bottle Compatibility with rPET Helps to Protect Performance Energy efficiency Whiteness 85–92 L* 30% less life cycle emissions Increased machinery life cycle due to reduced wear & tear 80–100% light blocking © 2024, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012

POLYSTRAND CONTINUOUS FIBER REINFORCED THERMOPLASTIC TAPES & LAMINATES ™ PRODUCT SELECTION GUIDE Material Min Finished Slit Width Max Finished Slit Width Unidirectional Tape 2” (50.8 mm) 24” (610 mm) X-Ply™, 3-Ply, 4-Ply 2” (50.8 mm) 120” (3048 mm) SLITTING CAPABILITIES Max Unfinished Width Max Finished Slit Width Max Finished Roll Weight Max Roll Length (X-Ply™, Full Width) Up to 125" (3175 mm) Up to 120" (3048 mm) Up to 10,000 lbs (4500 kg) Up to 4,000 ft (1200 m) LAMINATION LINE CAPABILITIES Tape Width Resin Capabilities Fiber Inputs Max Tape Roll Weight Max Roll Length 25" (635 mm) Standard Width, Slit Capabilities PP, PE, PETG, aPET, PA6 Additional polymers in development E-Glass S-Glass, Aramid Up to 1,800 lbs (816 kg) Up to 12,000 ft (366 m) TAPE LINE CAPABILITIES Product Name Resin Fiber Content Areal Weight Nominal Thickness1 Flexural Modulus Flexural Strength Tensile Modulus Tensile Strength wt % lb/ft2 oz/yd2 gsm in mm ksi GPa ksi MPa ksi GPa ksi MPa 6337 PP 63 0.10 14.75 500 0.015 0.38 3570 24.6 58 402 4010 27.6 111 765 6531 65 0.05 7.40 251 0.006 0.15 4020 27.7 73 505 4900 33.8 140 965 6536 0.07 10.32 350 0.009 0.23 4050 27.9 72 494 4500 31.0 131 903 6538 0.14 19.77 670 0.019 0.48 3540 24.4 47 324 4260 29.4 100 689 7034B PP-Black 70 0.07 10.24 347 0.009 0.23 4400 30.3 83 569 5000 34.5 111 765 6020 PE 60 0.08 11.95 405 0.012 0.30 3600 24.8 54 372 3800 26.2 109 752 6621 66 0.10 13.97 474 0.012 0.30 4000 27.6 55 379 4720 32.5 126 869 68222 68 0.16 23.34 791 0.022 0.56 4060 28.0 55 379 4560 31.4 113 779 5843 PETG 58 0.08 11.85 402 0.008 0.20 3680 25.4 90 621 4400 30.3 137 945 5840B aPET-Black 58 0.09 13.00 441 0.009 0.23 4120 28.4 107 738 5080 35.0 150 1034 5860B PA6-Black 58 0.08 11.48 389 0.010 0.25 3620 25.0 104 717 3970 27.4 108 745 TYPICAL PROPERTIES - UNIDIRECTIONAL FIBERGLASS REINFORCED THERMOPLASTIC TAPE 1 Nominal thicknesses indicated are baseline values that may vary depending on material processing and other variables. Contact Avient with your specific requirements. 2 6822 is only available in unidirectional tape—not as a multi-ply laminate. Contact Avient with your specific requirements. 2 No break occurred in testing.

激光打标⸺提高标识的可靠性和持久性，适用于所有类型的电缆护套 和绝缘材料 抗茵⸺保护电缆，避免滋生有害霉菌和细菌 防鼠咬功能母料⸺保护电缆，有效防止鼠类啃咬 防白蚁功能母料⸺保护电缆，有效防止白蚁侵蚀 成核剂⸺保持临界尺寸，调节收缩特性 发泡剂⸺减轻质量，降低树脂成本 紫外线稳定剂⸺保护树脂材料，延长产品寿命 抗氧化剂⸺维持物理属性 加工助剂⸺降低部分材料的口模流涎 适用于电力电缆应用的 ONCOLORTM 解决方案 建议使用量为 1-2%，使用量可能因具体用途、工艺、设备和树脂级别不同而存在差异。 海蓝色 适用于汽车电线的 ONCOLORTM 解决方案 适用于交联材料如 XLPE 的 EVA 色母料，以及适用于 T1、T2 和 T3 耐热等级要求的 PVC 色母料 建议使用量为 1-2%，使用量可能因具体用途、工艺、设备和树脂级别不同而存在差异 海蓝色 蓝色 (浅蓝) 适用于通信电缆和光缆应用的 PVC 和 PBT 色母料 适用于发泡和固体绝缘应用的 PE 色母料 为交联材料如 XLPE 专门设计的 EVA 色母料 所有材料建议使用量为 1-2%，使用量可能因具体用途、工艺、设备和合成树脂级不同而存在差异 适用于通信线缆应用的 ONCOLORTM 解决方案 海蓝色 蓝色 (浅蓝) 海蓝色 海蓝色 适用于室外线缆应用的抗紫外色母料 建议 PE 材料使用量为 2%，PVC 材料使用量为 3%，使用量可能因具体用途、工艺、设 备和树脂级别不同而存在差异 www.avient.com 版权所有© 2020埃万特公司。

TEMPERATURE Material Rear Center Front Nozzle Melt Mold Nylon 6,6 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) Nylon 6,6 30% SS 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) PBT 510–410 (265–280) 490–540 (255–280) 480–530 480–530 480–530 150–250 (65–120) PC 14% NiCF 540–570 540–570 530–560 530–560 530–560 150–250 (65–120) ABS 470–520 460–520 460–520 460–530 (240–275) 460–530 (240–275) 100–200 (40–90) PP 440–480 (225–250) 440–480 (225–250) 430–470 (220–245) 420–460 (215–240) 420–460 (215–240) 125–175 (50–80) DRYING Material Temperature °F (°C) Time Minimum Moisture Maximum Moisture Nylon 6,6 14% NiCF 180 (80) 4–5 hours 0.05% 0.20% Nylon 6,6 30% SS 180 (80) 4–5 hours 0.05% 0.20% PBT 14% NiCF 250 (120) 6-8 hours 0.02% 0.03% PC 14% NiCF 250 (120) 3–4 hours 0.02% 0.02% ABS 14% NiCF 200 (90) 2–4 hours 0.05% 0.10% PP 14% NiCF 180 (80) 2–4 hours 0.20% 0.30% Equipment • Feed throats smaller than 2.5" may cause bridging due to pellet size - Larger feed throats will be more advantageous with long fiber EMI shielding resins • General purpose metering screw is recommended - Mixing/barrier screws are not recommended • L/D ratio - 18:1–20:1 (40% feed, 40% transition, 20% metering) • Low compression ratio - 2:1–3:1 • Deep flights recommended - Metering zone 3.5 mm - Feed zone 7.5 mm • Check ring - Three-piece, free-flowing check ring • General purpose nozzle (large nozzle tips are recommended) - Minimum orifice diameter of 7/32" - Tapered nozzles are not recommended for long fiber EMI shielding resins • Clamp tonnage: - 2.5–5 tons/in2 Gates • Large, free-flow gating recommended - 0.25" x 0.125" land length - 0.5" gate depth Runners • Full round gate design • No sharp corners • Minimum of 0.25" diameter • Hot runners can be used PROCESSING Screw Speed Slower screw speeds are recommended to protect fiber length Back Pressure Lower back pressure is recommended to protect fiber length Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) PROCESS CONSIDERATIONS Recommended – retain fiber length (maximize conductivity) • Low shear process • Low screw speed and screw RPM • Slow Injection speed • Fill to 99–100% on first stage of injection - Reduces potential nesting of fibers at gate location - Improves mechanical performance near gate location - Promotes ideal fiber orientation Resin Rich Surface • Achieved when using a hot mold temperature and longer cure times ≥ Max mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could reduce attenuation performance in an assembly Fiber Rich Surface • Achieved when using a cold mold temperature and shorter cure times ≤ Minimum mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could improve attenuation performance in an assembly www.avient.com Copyright © 2020, Avient Corporation.