YELLOW 143C PA 6/12 PP FR 8-6 LMS-1000

In addition, the Nymax™ REC series offers PA6 and PA66 grades with post-industrial recycled (PIR) or post-consumer recycled (PCR) nylon to support a circular economy. Injection Molding Parameters Base Resin PA6 PA6 IM/ST PA6 GF PA6 GMF PA66 IM/ST PA66 GF Barrel Temperatures °F (°C) Rear Zone 450–490 (232–254) 440–490 (226–254) 490–510 (254–265) 480–500 (249–260) 510–530 (265–276) 510–530 (265–276) Center Zone 460–500 (238–260) 450–500 (232–260) 500–520 (260–271) 490–510 (254–265) 510–530 (265–276) 520–540 (271–282) Front Zone 470–510 (243–265) 460–510 (237–265) 510–525 (265–273) 500–520 (260–271) 530–550 (276–288) 530–550 (276–288) Nozzle 480–520 (249–271) 470–510 (243–265) 515–530 (268–276) 510–525 (265–273) 530–560 (276–293) 540–560 (282–293) Melt Temperature °F (°C) 480–520 (249–271) 470–510 (243–265) 515–530 (268–276) 510–525 (265–273) 530–550 (276–288) 540–560 (282–293) Mold Temperature °F (°C) 120–180 (49–82) 120–180 (49–82) 120–200 (49–93) 120–200 (49–93) 140–220 (60–104) 140–220 (60–104) Pack and Hold Pressure 50–80% of Injection Pressure Injection Velocity 1.0–4.0 in/sec Back Pressure 25–100 psi Screw Speed 35–80 rpm Drying Parameters 4 hours @ 180°F (82°C) Moisture Allowable 0.1–0.2% Cushion 0.250 in Screw Compression Ratio 2.0:1–2.5:1 Nozzle Type Reverse Taper Clamp Pressure 3–5 tons/in2 Processing Guide 3 Start Up & Shut Down Recommendations Purge Compound Polypropylene Recycling Recycling prime grades up to 20% is permissible and recycling PIR or PCR grades up to 10% is permissible. Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel • Decrease injection speed Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed Insufficient packing • Increase hold pressure and time • Increase shot size Processing Guide 5 Problem Cause Solution Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Increase shot size • Increase injection rate • Increase packing pressure • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Troubleshooting Recommendations 6 Nymax Polymer Formulations Troubleshooting Recommendations Problem Cause Solution Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Check moisture.

CELCON BEIGE V2 MATTE BLACK V2 DRIED PP FR 8-6 LMS-1000

APPLICATIONS • Automotive, consumer products, E&E products • PP, ABS, PC co-polyester, PA6, PA 66, PA12, and others on request KEY BENEFITS • Up to 10 hours glow depending on resin, activation energy, and pigment loading • Unlimited repetition of energy accumulation and emission process • Excellent temperature and chemical stability • Excellent weathering fastness and lightfastness • Limited influence on mechanical properties • Formulated with low-concern substances Copyright © 2023, Avient Corporation.

Available in a range of colors, the impact-modified nylon 6 formulation is customizable to serve a variety of consumer applications, including powersports, lawn & garden, and marine. Impact-modified nylon (PA6) grade formulated for cold temperature impact resistance and heat resistance. Discover comparison data and key properties of high-gloss Artisan™ pre-colored nylon (PA6) formulations

BLACK V2 PP FR 8-6 LMS-1000

BLACK PP LUCID BLACK V2 PP FR 8-6 LMS-1000

These materials are semi-crystalline and deliver excellent chemical resistance, low moisture uptake, and dimensional stability similar to nylon (PA6 and PA66). Producing polyketone results in 61% less carbon dioxide (CO2) than PA66 and 46% less than PA6. Grades are available in black and natural with 30%–50% long glass fiber, with or without a flame retardant, allowing customers to customize performance requirements for structural applications.

PE ORANGE MC-6756 F V2 MATTE BLACK V2 UNDRIED PP FR 8-6 LMS-1000

7489C GREEN TEA V2 433C TUXEDO BLACK V2 PP FR 8-6 LMS-1000