97076 YE Pearl PE MASTERBATCH FDM UR 194298 PK PEARL PP MASTERBATCH

0003236 GY STD K-RESINE MASTERBATCH 0003597 BL STD PP MASTERBATCH

FDM 269883 BK PC MASTERBATCH 274169 RD PE MASTERBATCH

199129 YE EVA MASTERBATCH 336942 YE PE MASTERBATCH

183168 BU SAN MASTERBATCH 183173 BN SAN MASTERBATCH

92522 NP EMA AA MASTERBATCH 116666 NP EMA AA MASTERBATCH

Colorant Chromatics PPSU Masterbatch - Colors for High Temperature Injection Molding Applications Smartbatch™ formulations blend design and function in one masterbatch solution 

Colorant Chromatics PPSU Masterbatch - Colors for High Temperature Injection Molding Applications Smartbatch™ formulations blend design and function in one masterbatch solution 

HDPE is not recommended for purging as it can cause delamination or lead to black specks. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase shot size • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Burning • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Warp • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Processing Guide 7 Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

% Specific Color Heat BROWN 83MB01 (c) Iron Oxide, Tan HR 60 1.78 PBr-11 1 I/O SBR 83MB02 (c) Iron Oxide, Light 68 2.1 PBr-6 2 C I/O SBR 83MB03 (c) Iron Oxide, Dark 60 1.83 PBr-6 2 C I/O SBR 83EP02 Iron Oxide, Light 69 1.98 PBr-6 2 C I/O EPDM 83EP03 Iron Oxide, Dark 69 1.98 PBr-6 2 C I/O EPDM BLACK 90MB01 (c) Furnace N-330 31 1.2 PBk-7 1 I/O SBR 90MB05 (c) Iron Oxide 60 1.8 PBk-11 2 C I/O SBR 90EP01 Furnace Black 33 1.05 PBk-7 1 I/O EPDM 90EP05 Iron Oxide 55 1.56 PBk-11 2 C I/O EPDM ALUMINUM 61MB01 Aluminum 70 1.5 PM-1 1 I/O SBR 61EP01 Aluminum 60 1.31 PM-1 1 I/O EPDM RS = Red Shade YS = Yellow Shade VYS = Very Yellow Shade BS = Blue Shade VBS = Very Blue Shade GS = Green Shade NC = Non-Crystallizing HR = Heat-Resistant (a) = Potential Migration at Low Use Levels (b) = Poor Alkali Resistance - Not Recommended for Open Steam Cure (c) = Six Month Shelf Life LIGHTFASTNESS I = Indoor Only I/O = Indoor or Outdoor Mass = Outdoor Masstone Application Only C = Some Caution Advised HEAT STABILITY 1 = Above 400°F 2 = 350°F–400°F 3 = Below 350°F C = Some Caution Advised 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.