Number: BC1228188 CERTIFICATE OF CHANGE OF NAME BUSINESS CORPORATIONS ACT I Hereby Certify that POLYONE CANADA ULC changed its name to AVIENT CANADA ULC on January 15, 2021 at 12:13 PM Pacific Time.

CERTIFICATE OF INCORPORATION ON CHANGE OF NAME Company Number 3141094 The Registrar of Companies for England and Wales hereby certifies that under the Companies Act 2006: POLYONE CORPORATION UK LIMITED a company incorporated as private limited by shares, havingits registered office situated in England and Wales, has changed its name to: AVIENT MATERIAL SOLUTIONS UK LIMITED Given at Companies House on9th November 2021.

By helping to achieve target rPET use percentage, where applied, Amosorb 4020L can help avoidance of potential plastic tax surcharges.

G1QCertificate Number: 82756 Certificate of Incorporation on Change Of Name For Registrar of Companies I hereby certify that CLARIANT PLASTICS & COATINGS (IRELAND) LIMITED having, by a Special Resolution of the Company, and with the approval of the Registrar of Companies, changed its name, is now incorporated as a LTD - Private Company Limited by Shares under the name AVIENT COLORANTS IRELAND LIMITED and I have entered such name on the Register accordingly.

Certificate Number: 255 ISO2P Date First Registered: 03/04/2023 Issued on: 11/04/2023 Valid until: 10/04/2026 Awarded to AVIENT PAKISTAN (PVT) LTD 1A/1, Sector#20, Korangi Industrial Area, Sector 20 Karachi, Pakistan In recognition of the Organization´s Food Safety Management System which complies with : ISO 22000:2018 Food Category : I For the scope of activities described below: Manufacturing & Processing of Polymer Resins & Master batch F-3/22/ A 100 Issue date : 06/2022 Version:03 It is mandatory to carry out the surveillance audit on its time.

Our diverse geographic footprint and identification of critical site redundancies moderately mitigates site-specific business interruption risk.

To participate in the audio-only portion of the call, dial 1-844-835- 7433 (domestic) or 1-914-495-8589 (international) and provide conference ID number 4774915. To listen to this recording, dial 1-855-859- 2056 (domestic) or 1-404-537-3406 (international) and provide conference ID number 4774915. They are based on management’s expectations that involve a number of business risks and uncertainties, any of which could cause actual results to differ materially from those expressed in or implied by the forward-looking statements.

Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Increase melt temperature • Increase injection rate • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Processing Guide 5 Problem Cause Solution Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Increase shot size • Increase injection rate • Increase pack pressure/time • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Troubleshooting Recommendations 6 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Burning Melt and/or mold too cold • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection rate • Increase mold temperature Mold design • Decrease injection rate • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Mold design Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase shot size • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase shot size • Increase injection rate • Increase packing pressure • Increase gate size Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection speed • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low Mold design • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Increase mold temperature • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation Mold design • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Mold design Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time TROUBLESHOOTING RECOMMENDATIONS www.avient.com Copyright © 2020, Avient Corporation.

No Content Detail 1 MERSIS number of the Company 0836003561100014 2 Title of the Company Polyone Tekno Polimer Mühendislik Plastikleri Sanayi ve Ticaret Anonim Şirketi 3 Registered office of the Company Orhan Gazi Mah.1683 Sk. No:8 Esenyurt/İstanbul 4 Committed and Paid Company Capital TRY 100,799,000.00 5 Full names of the Board members of the Company (in the event that a legal entity is a board member, that legal entity's MERSIS number, trade name, registered address and its individual representative's full name) • Holger Hans Kronimus • Christoph Palm • Zaneta Gabriela Potoczny 6 Independent auditor's title, registered address, and branch offices (if any).