Attending and Voting at the Annual Meeting PROXY SUMMARY Company Operating Performance Our Company Culture PROXY SUMMARY Impact of Our Performance on Named Executive Officer 2018 Compensation Annual Incentive Plan 2018 Annual Incentive Program Payouts Named Executive Officer 2018 Target Opportunity ($) Payout (%) Payout ($) Long-Term Incentive Program 2016 – 2018 Cash-Settled Performance Units Performance Measure: Adjusted EPS Performance Periods Weighting Target Result Payout % PROXY SUMMARY Our Director Nominees and Committee Membership Name Age Director Since Principal Position Notable Skills and Experiences Independent Committee Membership* (M=Member, C=Chair) AC CC N&GC EH&SC PROXY SUMMARY Name Age Director Since Principal Position Notable Skills and Experiences Independent Committee Membership* (M=Member, C=Chair) AC CC N&GC EH&SC Average Tenure Average Age Gender Diversity 5.25 59 30% Governance Highlights Director Independence Independent Lead Director PROXY SUMMARY Board Oversight of Risk Management Stock Ownership Requirements Board Practices PROXY STATEMENT POLYONE CORPORATION PolyOne Center 33587 Walker Road Avon Lake, Ohio 44012 PROXY STATEMENT Dated March 28, 2019 ELECTION OF BOARD OF DIRECTORS PROPOSAL 1 — ELECTION OF BOARD OF DIRECTORS Our Board recommends a vote FOR all the nominees listed below.

Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Increase melt temperature • Increase injection rate • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Processing Guide 5 Problem Cause Solution Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Increase shot size • Increase injection rate • Increase pack pressure/time • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Troubleshooting Recommendations 6 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Burning Melt and/or mold too cold • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection rate • Increase mold temperature Mold design • Decrease injection rate • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

• Vents should be placed at the intersection of each 90° bend in the runner system off of the cold slug well and vented to atmosphere PROBLEM CAUSE SOLUTION Black Specks Contamination • Purge barrel with general purpose PP • Verify correct nozzle is being used • Pull screw for cleaning Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded-in stress Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed Insufficient packing • Increase hold pressure and time • Increase shot size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Troubleshooting Recommendations PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full • Increase shot size Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Troubleshooting Recommendations (continued) PROBLEM CAUSE SOLUTION Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Warp Process related • Increase cooling time • Increase melt temperature • Increase pack pressure • Increase pack time • Decrease mold temperature Mold design • Inspect for non-uniform mold cooling Part design • Inspect for non-uniform wall thickness Temperature control unit incorrect temperature • Check settings • Inspect thermocouple Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase injection rate • Increase mold temperature Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

Avient Expands High-Performance Recycled-Content Polycarbonate Solutions for Electrical & Electronics Industry to EMEA...

PolyOne IR Presentation – Global High Yield & Leveraged Finance Conference – 2/24/2020 to 2/26/2020

PolyOne IR Presentation – Global High Yield & Leveraged Finance Conference – 2/24/2020 to 2/26/2020

PolyOne IR Presentation – Global High Yield & Leveraged Finance Conference – 2/24/2020 to 2/26/2020

PolyOne IR Presentation – Global High Yield & Leveraged Finance Conference – 2/24/2020 to 2/26/2020

PolyOne IR Presentation – Global High Yield & Leveraged Finance Conference – 2/24/2020 to 2/26/2020

Industrial Valle del Cinca S/N Apartado , E-22300 Barbastro, Spain Avient Corporation Design and Manufacture of Colorants and Compounds for Fluoropolymer and High Temperature Polymers. 19 Francis J Clark Circle Bethel CT 06801 United States Avient Corporation Design and Manufacture of Colorants and Additives for Plastics 03 Street 02, VSIP 820000 Thuận An Binh Duong Vietnam Avient Corporation Design and Manufacture of Colorants and Additives for Plastics Lot 1232, MK. 15, Kawasan Industri, Kecil & Sederhana Butterworth Penang 14120 Malaysia Avient Corporation Design and Manufacture of Colorants and Additives for Plastics Autopista Medellín Km 2.5, Via Parcelas Km 1, Vereda Siberia , 250017 Cota, Colombia Avient Corporation Design and Manufacture of Colour and Additive Concentrates, Thermoplastic Resins and Specialty Compounds Ihsan Dede Cad. , 41448 Gebze, Türkiye Avient Corporation Design and Manufacture of Colorants and Additives for Plastics 2#, Nanyunsan Rd, Huangpu District, Science City, Guangzhou Hi-Tech Industrial Development Zone , 510663 Guangzhou, Avient Corporation Design and Manufacture of Colorants and Additives for Plastics Avenida 34-11, Zona 12 Complejo Parque Gobal , 01012 Guatemala City, Guatemala Avient Corporation Design and Manufacture of Specialty Engineered Thermoplastics Orhangazi Mah. 1683 Sok.