Infant & Child Products

Infant & Child Products

Infant & Child Products

Infant & Child Products

Increase pack and hold pressure 5. Increase hold pressure 2. Increase hold time 3.

All Avient manufacturing facilities comply with applicable regulatory requirements regarding emissions limits and hold valid air permits where required.

Processing Guidelines Base Resin PA6 Barrel Temperatures °F °C Rear Zone 440–470 227–243 Center Zone 450–480 232–249 Front Zone 460–490 238–254 Nozzle 470–500 243–260 Melt Temperature 470–500 243–260 Mold Temperature 120–180 49–82 Pack and Hold Pressure 50–75% of Injection Pressure Injection Velocity 0.5 in/s–3 in/s 13 mm/s–76 mm/s Back Pressure 50–100 psi 3.4–6.9 Bar Screw Speed 30–70 rpm Cushion 0.25 in 6.35 mm Drying Parameters 2–4 Hours @ 180°F 2–4 Hours @ 82°C Moisture % Allowable 0.08–0.18%* Screw Type General Purpose Screw Screw Compression Ratio 2.0:1– 2.5:1 Screw L/D 20:1 Non-return Check Valve Free Flow Check Ring Nozzle Type Reverse Taper Clamp Pressure 2–3 Tons/in² Barrel Capacity 30-80% of barrel should be used * Avient suggests measuring moisture using a Karl Fischer method or Vapor Pro® moisture analyzer that titrates only for moisture. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Troubleshooting Recommendations Problem Cause Solution Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Problem Cause Solution Warp Process related • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Troubleshooting Recommendations Processing Guide 7 Troubleshooting Recommendations Problem Cause Solution Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

BASE RESIN ABS Drying Temperature 80–90°C Drying Time 2–3 Hours Barrel Temperatures °C Rear Zone 180–210 Center Zone 190–220 Front Zone 200–230 Nozzle 210–240 Mold Temperature 50–80 Screw Speed Moderate Back Pressure 3–10 bar Cushion 5–15 mm Injection Speed Low to medium Injection Pressure Moderate to high Holding Pressure 10–30% of injection pressure Screw Type General purpose Screw L/D 20:1 Screw Compression Ratio 2.0:1–2.5:1 Non-return Check Valve Free flow check ring Nozzle Type Reverse taper Barrel Capacity 30–80% of barrel should be used STARTUP & SHUTDOWN RECOMMENDATIONS Purge Compound 2–3 melt flow PP or purging compound. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold temperature too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Warp Process related • Increase melt temperature • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding TROUBLESHOOTING RECOMMENDATIONS 1.844.4AVIENT www.avient.com Copyright © 2021, Avient Corporation.

F -27, MIDC, Ranjangaon, Taluka – Shirur, Pune Maharashtra 412220 India Hold this Opinion Statement No. 798019/2023 The Organization has demonstrated that they have followed the guidelines provided for Good Manufacturing Practices as per the ICHQ7 guidelines in their organization for the following Business activity: Research and Development, Manufacture of Color additives, Concentrates and Specialty Formulations for intended use in pharma and other industries Theuns Kotze, Managing Director – IMETA Assurance Last Audit Date: 31.10.2023 BSI Group India Private Limited T: +91-4762-9000 (CIN U74899DL1999PTC101381 info.in@bsigroup.com The Mira Corporate Suites bsigroup.com/en-IN Plot 1&2, Ishwar Nagar, Mathura Road New Delhi-110065, India