BASE RESIN PPA PC PSU PES PPS CO- POLYMER ACETAL PEEK PA Barrel Temperatures* °F (°C) Rear Zone 550–580 (288–305) 520–560 (271–293) 600–640 (316–338) 630–660 (332–338) 550–580 (288–304) 350–370 (177–188) 660–700 (349–371) 440–490 (227–254) Center Zone 560–600 (293–316) 530–570 (277–299) 620–670 (327–354) 650–680 (343–360) 560–615 (293–324) 380–390 (193–200) 700–730 (371–388) 470–510 (243–266) Front Zone 580–620 (304–327) 550–580 (288–305) 630–680 (332–360) 670–730 (354–388) 590–630 (310–332) 390–430 (200–221) 720–750 (382–400) 490–540 (254–282) Nozzle 575–615 (302–324) 550–600 (288–316) 630–680 (332–360) 680–700 (360–371) 600–625 (316–330) 380–415 (193–213) 720–750 (382–400) 520–570 (271–300) Melt Temperature 575–615 (302–324) 560–600 (293–316) 625–675 (330–358) 650–710 (343–377) 600–625 (316–330) 370–410 (188–210) 670–740 (354–393) 520–570 (271–300) Mold Temperature 250–300 (121–150) 175–240 (80–116) 190–300 (88–150) 225–325 (107–164) 250–325 (121–164) 150–225 (66–107) 290–375 (143–190) 150–200 (66–93) Pack & Hold Pressure 50%–75% of Injection Pressure Injection Velocity in/s 1.0–3.0 Back Pressure psi 50 Screw Speed rpm 50–90 Drying Parameters °F (°C) 6 hrs @ 175 (80) 4 hrs @ 250 (121) 4 hrs @ 275 (135) 4 hrs @ 300 (150) 4 hrs @ 250 (121) 2 hrs @ 200 (93) 3 hrs @ 300 (150) 4 hrs @ 180 (82) Allowable Moisture % < 0.05 < 0.02 < 0.02 < 0.04 < 0.02 0.15–0.20 < 0.02 0.10–0.20 Cushion in 0.125–0.250 Screw Compression Ratio 2.5:1–3.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose Reverse Taper Clamp Pressure 5–6 Tons/in2 of projected area of cavities and runner system * Barrel temperatures should be elevated for compounds designed for electrical insulative properties. Venting • Place vents at the end of fill and anywhere potential knit/weld lines will occur. • All vents need to be vented to atmosphere. • For circular parts, full perimeter venting is recommended. • Cut vent depths to: - PPA Compounds: 0.0015"–0.0025" depth and 0.250" width - PC Compounds: 0.002"–0.004" depth and 0.250" width - PSU Compounds: 0.003"–0.004" depth and 0.250" width - PES Compounds: 0.003"–0.004" depth and 0.250" width - PPS Compounds: 0.002"–0.003" depth and 0.250" width - Acetal Compounds: 0.0015" minimum depth and 0.250" width - PEEK Compounds: 0.002"–0.004" depth and 0.250" width - Nylon Compounds: 0.002" minimum depth and 0.250" width • Increase vent depth to 0.060" (1.5mm) at 0.250" (4.0mm) away from the cavity and vent to atmosphere.

Cesa laser marking solutions can be used with a variety of thermoplastics including, but not limited to: • PP • PC/ABS • Polyamide • Polyacetal (POM) Applications include: • Traceability, UPC, Branding • Food Packaging Lot Codes • Industrial Safety Tags & Equipment • Wire & Cable Part Numbers & Gauge Size • Automotive Components • PE • PET • PMMA • Polyolefins PRODUCT BULLETIN WHY LASER MARKING?

BENEFITS • High additive loading for optimal UV stabilization • Solutions available for a large number of injection molded polymers including PP, PE, PS, HIPS, ABS, SAN, PA (nylon), PBT, Co-PET, PC, POM and TPU • Can be combined with colors and other additives in Smartbatch™ solutions • Formulations can be customized to meet specific regulatory compliance, e.g., EU and US food contact, toy, UL 94 recognition PRODUCT BULLETIN Copyright © 2023, Avient Corporation.

High-temperature polymers (HTP) processed include: LCP, PEEK, PAEK, PEKEKK, PEI, PES, PSU, PPSU, and PPS FLUOROPOLYMERS Colorant Chromatics has extensive experience in selecting the best pigments and additives for optimal performance under demanding circumstances. FP compounds for: PFA, FEP, ECA, ETFE, ECTFE, PTFE, and PVDF HTP compounds for: PEI, PES, PSU, PPSU, PPS, LCP, PEEK, PAEK, and PEKEKK Colorant Chromatics specialty compounds offer property enhancements such as: • Mechanical strength • Static dissipation • X-ray opacity • Electrical performance • Low dielectric performance • Mold release • Laser marking • Transcend™ Premier Healthcare Colorants (biocompatible) ADDITIVE CONCENTRATE FORMULATIONS Colorant Chromatics additive solutions can provide your solutions with additional functionality such as: • Improved lubricity • Lightweighting through foaming, by both physical and chemical foaming • Heat reduction through �SiteCool™ infra-red absorption technologies for roofing applications • Laser marking solutions or other added value properties NON-PFAS MOLD RELEASE ADDITIVES Colorant Chromatics™ Evoluscend™ is a non-PFAS* high-temperature polymer mold release additive developed to boost production efficiency and product quality for manufacturers. Evoluscend is effective across a range of high- temperature polymers, including PEEK, PPSU, PES, PSU, PEI, LCP, and PPS, with a maximum service temperature exceeding 150°C. * Manufactured without intentionally added PFAS and without PTFE CHEMICAL FOAMING ADDITIVES Colorant Chromatics chemical foaming solutions for fluoropolymer wire insulation can reduce part density while enhancing the stability and efficiency of the manufacturing process without the need to invest in additional equipment for physical foaming with blowing agents.

FIBER MANUFACTURER T E X T I L E S & F A B R I C S • Provide a Product Carbon Footprint (PCF) calculation to align with ISO 14067:2018 and to help in meeting sustainability goals • Procure feedstock from renewable resources • Maintain comparative performance to conventional carbon black • Achieve color stability under xenon arc and TUV testing • Offer solutions for rPET, PP, PE, PBT, and PA6 where a desire for environmentally responsible products exists • Offered sustainable platform approach supported by extensive fiber expertise • Helped meet sustainability targets while attaining all design and engineering goals • Supplied necessary PCF calculation certified by TÜV Rheinland and aligning with ISO 14067 requirements • Provided effective alternative to virgin carbon black • Achieved reductions in CO2e emissions vs. conventional technology, moving toward carbon- negative OnColor™ REC Polymer Colorants KEY REQUIREMENTS WHY AVIENT?

母粒和预着色料可用于多种聚合物，包括PE， PP，PEBA，PC，ABS等。 ™ 在三个通过ISO 13485认证的医疗产线生产 全球统一的配方，提供全球一致性和供应链 保障 提供文件化的变更控制 原料指纹图谱和常规批次测试 多种标准颜色缩短产品开发时间 产品组合里符合标准的颜色用于： - 注射针头ISO 6009 - 眼科容器盖（美国眼科学院 / AAO - American Academy of Ophthalmology） 颜色 潘通色 参照 PE 基料 PP 基料 透明PP 基料 PEBA 基料 PC 基料 ABS 基料* — PE0M176031 PP0M176045 ** AH0M415001 NC0M176058 ** SB0M665206 102C PE1M176076 PP1M176060 PP1M176062 AH1M415002 NC1M176058 NC1M176059 SB1M664958 158C PE2M176044 PP2M176046 ** ** NC2M176044 NC2M664912 SB2M664939 199C PE3M176131 PP3M176111 PP3M176113 AH3M415002 NC3M176116 NC3M176122 SB3M665037 196C PE3M176130 PP3M176109 ** AH3M415001 NC3M176117 NC3M665052 SB3M665039 2593C PE4M176023 PP4M176036 PP4M176039 AH4M415001 NC4M176038 NC4M176044 SB4M664978 292C PE5M176155 PP5M176169 ** AH5M415003 NC5M176142 ** SB5M665402 285C PE5M176154 PP5M176171 PP5M176175 AH5M415002 NC5M176143 NC5M176146 SB5M665404 288C PE5M176153 PP5M176173 ** ** NC5M176144 ** SB5M665406 346C PE6M176128 PP6M176111 ** ** NC6M176118 ** SB6M665070 3145C PE6M176126 PP6M176115 ** ** NC6M176119 ** SB6M665068 348C PE6M176127 PP6M176113 PP6M176118 AH6M415001 NC6M176120 NC6M176121 SB6M665072 425C PE7M176066 PP7M176091 PP7M176094 ** NC7M176124 ** SB7M665297 Cool Gray 5C PE7M176067 PP7M176089 ** AH7M415001 NC7M176125 NC7M665175 SB7M665295 7502C PE8M176048 PP8M176058 ** ** NC8M176058 ** SB8M664871 463C/731C PE8M176049 PP8M176060 ** ** NC8M176059 ** SB8M664869 Black C PL9M176008 PP9M176017 ** ** NC9M176008 NC9M176009 SB9M664896 颜色可能与显示的实际颜色有所不同。

TAILORING TACK BY BLENDING VERSAFLEX PF Film Thickness: 39 micron LDPE/13 micron Versaflex PF F = Final tack after 7 days @ 25° C i = Initial tack after 20 mins @ 25° C Pe el S tr en gt h on S te el , N /2 5m m Pe el S tr en gt h on S te el , N /2 5m m PEEL STRENGTH ON STAINLESS STEEL Film Thickness: 51 micron LDPE/25 micron Versaflex PF F F F F F F F i i i i i i i www.avient.com Copyright © 2020, Avient Corporation.

HDPE, PP, POM Fast acting new generation nucleant for PE and PP; improved dimensional stability, thermal and mechanical properties  Protection from moisture for improved barrier Reduced Moisture Vapor Transmission Rate (MVTR) HDPE ready-to-use formulation; moisture absorbing concentrates   Protection from oxygen scavenging in PET Reduced transmission of oxygen vacuum loss in BCT (blood collection tubes) and protect reagents from oxygen degradation   Protection from UV in transparent containers (PP, PE, PETG, COP) UV blocking in 290–450nm with no impact on clarity; protection of light sensitive reagents     Copyright © 2022, Avient Corporation.

Page 8 of 11 0 0.5 1 1.5 2 2.5 3 3.5 4 Pe el fo rc e, N /m m 60 A -I 60 A -II 75 A- III 55 A- IV 65 A -V 50 A- VI 70 A- V II TPE Grade Capron 8333GHI 260C 276C 288C Figure4. Adhesion comparison of commercially available TPEs and TPVs with Universal TPEs: Zytel 70G33L. 0 0.5 1 1.5 2 2.5 3 3.5 4 Pe el fo rc e, N /m m 60 A- I 60 A -II 75 A -II I 55 A- IV 65 A- IV 50 A- VI 70 A- VI I TPE Grade Zytel 408HS 260C 276C 288C Figure 7. Page 10 of 11 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Pe el fo rc e, N /m m 60 A- I 60 A- II 75 A- III 55 A- IV 65 A- IV 50 A- V I 70 A- VI I TPE Grade Zytel 409AHS 260C 276C 288C Figure 8.

Product range • Flame retardants to reduce flammability of fibers and fabrics especially in building and construction applications • Light stabilizers to protect fibers used outdoors or exposed to sunlight against UV light • Antimicrobials to protect hygienic fiber products from bacteria proliferation • Antistatics to reduce electrostatic charges • Antioxidants to reduce polymer oxidation during spinning and protect fabrics during service life • Optical brighteners to provide a brilliant white effect and blueish hue • Electrets to retain electrostatic charge on the polymer surface for a longer period of time in filtration applications • Hydrophobics to impart durable water repellency • Chain extenders for recycled polyester fibers • Others on request Product characteristics • Good spinnability • Fiber-specific QC and protocols • Lot-to-lot consistency • Carriers: PET, PBT, PA 6, PP, and others • Possibility to combine colors and additives into a combination concentrate for convenience • Product guidance from our fiber expert team • Focus on safe and sustainable formulations Applications • Continuous filaments (POY, FDY, HOY, BCF) • Long and short spinning staple fiber • Nonwoven processes (spunbond and meltblown) Cesa™ Fiber Additives MagIQ™ Liquid Fiber Colorants & Additives Multiple color production • Depending on the manufacturing set-up, several injection points can be added to enable multiple color production at the same time on a single extruder Batch size flexibility • Fiber producers can manufacture anything from a few kilograms to hundreds of tons using the same simple process Rapid color changes • No extruder contamination and easy color-on, color-off operation increases color change speed Waste reduction • Rapid color changes, precise metering and the ability to adjust color in-line reduces waste during color changeovers Continuous metering & long spin pack life • High pigment and dye concentrations mean fewer pack changes are required • Where color is running low for larger volume runs, low level metering sensors alert operators and packs can be changed without disrupting production In-line IV adjustment • Specialist additives are available to adjust Intrinsic Viscosity (IV) in-line for rPET applications • These additives are available as single products, or can be combined with color to create a multi- functional formulation Color design service • Avient offers a dedicated color design service to help shorten product development cycles and enhance market agility Liquid color processing • Formulations are stable at temperatures up to 60°C and retain good flow properties at temperatures as low as 10°C • These formulations can help lower yarn friction and abrasion, and there is no fuming or evaporation during production Avient’s liquid fiber colorant technology combines advanced liquid color formulations with state-of-the-art, high-pressure metering equipment to enable late-stage injection of liquid color for spun-dyed polymer melt.