ABS WHITE ABS LT. ABS DK.

ABS GRAY 106745 3% ABS GREY 428C 3% ABS WHITE 35636 5%

METALLIC COPPER ABS METALLIC BLACK ABS UV CLEAN WHITE ABS

BLUE LM ABS GREEN LM ABS RED LM ABS

101I ZUMA CREAM ABS DESERT SAND ABS E-100I MOJAVE ABS

BLACK 7C ABS BLACK 431C ABS BLACK 432C ABS

ABS WHITE V2 PC/ABS WHITE PV/ABS ROYAL BLUE

ABS IVORY V2 ABS GREEN V2 ABS ORANGE V2

ABS DK BLUE ABS WHITE UV ABS 252C PLUM

Base Resin PC PC/PSU PES PEI PP ABS PEEK PA Barrel Temperatures* °F (°C) Rear Zone 530–560 (277–293) 550–575 (288–302) 660–700 (349–371) 675–725 (357–385) 390–420 (199–216) 425–460 (219–238) 680–730 (360–388) 430–500 (221–260) Center Zone 515–560 (269–288) 540–565 (282–296) 650–690 (343–366) 655–710 (352–377) 380–405 (193–207) 415–450 (213–232) 670–710 (354–377) 420–490 (216–254) Front Zone 510–525 (266–274) 530–555 (277–291) 640–680 (338–360) 655–700 (346–371) 370–395 (188–202) 405–440 (207–227) 650–690 (343–366) 410–480 (210–249) Nozzle 520–535 (271–280) 540–565 (282–296) 650–690 (343–366) 665–710 (352–377) 380–400 (193–204) 415–450 (213–232) 660–700 (349–371) 420–490 (216–254) Melt Temperature 525–560 (274–293) 530–580 (277–304) 650–700 (343–371) 660–730 (349–388) 375–395 (191–202) 410–460 (210–238) 650–730 (343–388) 420–500 (216–260) Mold Temperature 175–250 (80–121) 160–220 (71–104) 280–350 (138–177) 275–350 (135–177) 100–135 (38–57) 150–180 (66–82) 300–425 (149–219) 160–230 (71–110) Pack & Hold Pressure 50%–75% of Injection Pressure Injection Velocity in/s 0.5–2.0 Back Pressure psi 50 Screw Speed rpm 40–70 40–70 40–70 40–70 40–70 40–70 40–70 40–70** Drying Parameters °F (°C) 6 hrs @ 250 (121) 4 hrs @ 250 (121) 4 hrs @ 275 (135) 4 hrs @ 250 (121) 3 hrs @ 300 (150) 2 hrs @ 200 (93) 3 hrs @ 275 (135) 4 hrs @ 180 (82) Cushion in 0.125–0.250 Screw Compression Ratio 2.0:1–2.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose Reverse Taper Clamp Pressure 5–6 Tons/in2 * A reverse temperature profile is important to obtain optimum conductive properties. Venting • Place vents at the end of fill and anywhere potential knit/weld lines will occur. • All vents need to be vented to atmosphere. • For circular parts, full perimeter venting is recommended. • Cut vent depths to: - PC Compounds: 0.001"–0.002" depth and 0.250" width - PC/PSU Compounds: 0.002"–0.003" depth and 0.250" width - PES Compounds: 0.003"–0.004" depth and 0.250" width - PEI Compounds: 0.001"–0.003" depth and 0.250" width - PP Compounds: 0.001"–0.002" depth and 0.250" width - ABS Compounds: 0.0015"–0.0025" depth and 0.250" width - PEEK Compounds: 0.002"–0.004" depth and 0.250" width - Nylon Compounds: 0.002" min. depth and 0.250" width • Increase vent depth to 0.040" (1.0mm) at 0.250" (4.0mm) away from the cavity and vent to atmosphere.