STAN-TONE VC-34644 FR VANILLA 349F2 PG 19881 OR PP PP FR 8-6 LMS-1000

Onflex-S FR 60A-3S1846 Natural UV TAN PP PP FR 8-6 LMS-1000

PP XC 700 WHITE XMAXXAM FR C6 GF/30 H XF V0 RED 70 PP FR 8-6 LMS-1000

Base Resin ABS PA PBT PC PE PEEK PP PPS Barrel Temperatures °F (°C) Rear Zone 400–475 (200–250) 480–540 (248–282) 480–520 (250–270) 480–570 (250–300) 400–445 (200–230) 660–700 (350–475) 400–440 (200–225) 520–600 (270–300) Center Zone 410–480 (205–253) 490–550 (254–287) 485–525 (251–273) 500–580 (260–305) 410–455 (207–237) 670–710 (357–385) 410–450 (205–230) 550–610 (285–310) Front Zone 420–490 (210–257) 500–560 (260–293) 490–530 (254–276) 515–590 (267–310) 420–465 (213–243) 680–720 (363–400) 420–455 (215–235) 570–620 (300–320) Nozzle 425–500 (215–260) 510–570 (265–298) 490–540 (254–282) 530–600 (275–315) 430–475 (220–250) 700–730 (370–395) 430–460 (220–240) 610–620 (320–325) Melt Temperature 425–515 (215–270) 510–570 (265–298) 490–540 (254–282) 530–615 (275–325) 430–495 (220–260) 700–725 (370–385) 430–475 (220–250) 610–635 (320–335) Mold Temperature 140–200 (60–90) 150–300 (65–148) 140–280 (60–137) 160–240 (70–115) 80–140 (25–60) 300–400 (150–200) 80–140 (25–60) 190–300 (90–150) Drying Parameters 190 (90) 2–4 Hours 0.01%–0.15% 180 (82) 4–5 Hours 0.10%–0.20% 275 (135) 3–4 Hours 0.02%–0.04% 250 (125) 3–4 Hours 0.02% 160 (70) 2 Hours 300 (150) 3–4 Hours 0.10% 160 (70) 2 Hours 280 (135) 2–3 Hours 0.01%–0.20% Nozzle Type General Purpose Nylon or Reverse Taper General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose Injection Velocity1 2–5 in/sec; 50–127 mm/sec Injection Pressure 1,000–2,000 psi; 7–14 Mpa Back Pressure 50–100 psi; 0.3–0.7 Mpa Screw Speed 25–75 RPM Cushion 0.125–0.250 in; 3–6 mm Screw Compression Ratio2 2.0:1–2.5:1 Comments 1. Venting Guidelines by Resin • PC: .001"–.002" depth & .250" width • PC/PSU: .002"–.003" depth & .250" width • PES: .003"–.004" depth & .250" width • PEI: .001"–.003" depth & .250" width • PP: .001"–.002" depth & .250" width • ABS: .0015"–.0025" depth & .250" width • PEEK: .002"–.004" depth & .250" width FIGURE 40 - Venting Guidelines Vent Groove Vent Land Vent FIGURE 44 - Venting guidelines FIGURE 43 - Venting areas 20 Gravi-Tech CHAPTER 5 | PROCESS OPTIMIZATION Process optimization ensures a quality process and minimizes cycle time.

XBERGAMID FR BF6000-5001 RS NHFR HS NAT PP TRL. PP FR 8-6 LMS-1000

BLUE PP X PP FR 7C11 XND Snow White PP FR 8-6 LMS-1000

FB510 BT-HENDEE BLUE FR/UV PP FROST 2 PP FR 8-6 LMS-1000

PEACH FUZZ PBT/PC FR CMPD BLUE PP HC PP FR 8-6 LMS-1000

PG 92488.00 BU PP FB544MD OFF-WHITE FOAM/FR PP FR 8-6 LMS-1000

PURPLE FR PP GREEN JACKET 2423U PP FR 8-6 LMS-1000