ABS OFF WHITE PG 173293.01 GN PE PG 173289.01 WT PE

PE RED PEARL OUTER WHITE UV BROWN LATTICE PE

PG 114922.01 BU PE PE BLACK CUP PG 198313.00 OR PE

PE GREEN 3275 PE GOLD 465 ROSA PASTEL 495C PE

UV LT TAN 4001C PE BASE UV DK TAN 4006C PE BASE UV GREEN 5773C PE BASE

PG 183391.00 PEARL OR PE PG 183395.00 PEARL PK PE PG 183389.00 WT PE

WHITE O2B PE PE 300C BLUE 2 PE VIOLET C 2

WHITE PET WHITE UV PE GRAY UV PE

Base Resin PC PC/PSU PES PEI PP ABS PEEK PA Barrel Temperatures* °F (°C) Rear Zone 530–560 (277–293) 550–575 (288–302) 660–700 (349–371) 675–725 (357–385) 390–420 (199–216) 425–460 (219–238) 680–730 (360–388) 430–500 (221–260) Center Zone 515–560 (269–288) 540–565 (282–296) 650–690 (343–366) 655–710 (352–377) 380–405 (193–207) 415–450 (213–232) 670–710 (354–377) 420–490 (216–254) Front Zone 510–525 (266–274) 530–555 (277–291) 640–680 (338–360) 655–700 (346–371) 370–395 (188–202) 405–440 (207–227) 650–690 (343–366) 410–480 (210–249) Nozzle 520–535 (271–280) 540–565 (282–296) 650–690 (343–366) 665–710 (352–377) 380–400 (193–204) 415–450 (213–232) 660–700 (349–371) 420–490 (216–254) Melt Temperature 525–560 (274–293) 530–580 (277–304) 650–700 (343–371) 660–730 (349–388) 375–395 (191–202) 410–460 (210–238) 650–730 (343–388) 420–500 (216–260) Mold Temperature 175–250 (80–121) 160–220 (71–104) 280–350 (138–177) 275–350 (135–177) 100–135 (38–57) 150–180 (66–82) 300–425 (149–219) 160–230 (71–110) Pack & Hold Pressure 50%–75% of Injection Pressure Injection Velocity in/s 0.5–2.0 Back Pressure psi 50 Screw Speed rpm 40–70 40–70 40–70 40–70 40–70 40–70 40–70 40–70** Drying Parameters °F (°C) 6 hrs @ 250 (121) 4 hrs @ 250 (121) 4 hrs @ 275 (135) 4 hrs @ 250 (121) 3 hrs @ 300 (150) 2 hrs @ 200 (93) 3 hrs @ 275 (135) 4 hrs @ 180 (82) Cushion in 0.125–0.250 Screw Compression Ratio 2.0:1–2.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose Reverse Taper Clamp Pressure 5–6 Tons/in2 * A reverse temperature profile is important to obtain optimum conductive properties. Venting • Place vents at the end of fill and anywhere potential knit/weld lines will occur. • All vents need to be vented to atmosphere. • For circular parts, full perimeter venting is recommended. • Cut vent depths to: - PC Compounds: 0.001"–0.002" depth and 0.250" width - PC/PSU Compounds: 0.002"–0.003" depth and 0.250" width - PES Compounds: 0.003"–0.004" depth and 0.250" width - PEI Compounds: 0.001"–0.003" depth and 0.250" width - PP Compounds: 0.001"–0.002" depth and 0.250" width - ABS Compounds: 0.0015"–0.0025" depth and 0.250" width - PEEK Compounds: 0.002"–0.004" depth and 0.250" width - Nylon Compounds: 0.002" min. depth and 0.250" width • Increase vent depth to 0.040" (1.0mm) at 0.250" (4.0mm) away from the cavity and vent to atmosphere.

PP MILKY WHITE FROST 2 WHT PRL PE MOCA PE