Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Increase melt temperature • Increase injection rate • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Processing Guide 5 Problem Cause Solution Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Increase shot size • Increase injection rate • Increase pack pressure/time • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Troubleshooting Recommendations 6 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Burning Melt and/or mold too cold • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection rate • Increase mold temperature Mold design • Decrease injection rate • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

In the “Subtotal” section, you can enter values and select tax rates for shipping, handling, and miscellaneous costs. Applicable tax rates are determined by the tax code on the invoice. The tax rate is a government regulated rate to be paid to the tax authorities as part of the sale and is shown as a percentage.

Avient determined that the manufacturer required a material with a unique combination of properties, including: • Processing ease – high flow rate, ability to fill multi-cavity molds, thin-wall capabilities • Superior toughness – strength and durability to ensure dimensional integrity of the part • Repeatable performance – consistent conductivity for accurate measurement of liquids While several off-the-shelf compounds were evaluated, a new formulation was developed to meet the manufacturer’s specific needs as well as provide signifi cant benefi ts in reduced cycle time, increased production and reduced scrap rate. THE IMPACT For the manufacturer, Trilliant™ HC specialty engineered materials provided a number of advantages that contributed to the success of the new product line: • Reduced Cycle Time: The high flow properties of the Trilliant HC formulation allowed the manufacturer to produce warp-free parts that require less packing and cooling time, resulting in a 40% cycle time reduction. • Increased Production: Additionally, the high flow properties of the Trilliant HC formulation allowed for an increase in the number of cavities in the mold, resulting in a machine cost-per-part savings of over 30%. • Reduced Scrap Rate: The consistent conductivity, improved warp resistance, reduced flash, and improved durability provided by the Trilliant HC formulation meant less breakage, fewer rejects and a 40% reduction in scrap rate. • Total Manufacturing Cost Savings: Despite an increase I price per pound over the competition, the manufacturer’s total cash costs were reduced by over $45,000 on an annualized basis as a result of the proven, quantified savings in cycle time, productivity and scrap.

Edgetek™ Engineered Polymer Formulations achieved a UL 94 V-0 flammability rating certification for server cabinets

Factors that could cause actual results to differ materially from those implied by these forward-looking statements include disruptions, uncertainty or volatility in the credit markets that could adversely impact the availability of credit already arranged and the availability and cost of credit in the future; the effect on foreign operations of currency fluctuations, tariffs and other political, economic and regulatory risks; the current and potential future impact of the COVID-19 pandemic on our business, results of operations, financial position or cash flows including without any limitation, any supply chain and logistics issues; the speed and strength of growth in the global 5G infrastructure market; our ability to achieve the strategic and other objectives relating to the acquisition of Clariant's Masterbatch business, including any expected synergies; changes in polymer consumption growth rates and laws and regulations regarding plastics in jurisdictions where we conduct business; fluctuations in raw material prices, quality and supply, and in energy prices and supply; production outages or material costs associated with scheduled or unscheduled maintenance programs; unanticipated developments that could occur with respect to contingencies such as litigation and environmental matters; an inability to achieve the anticipated financial benefit from initiatives related to acquisition and integration working capital reductions, cost reductions and employee productivity goals; our ability to pay regular quarterly cash dividends and the amounts and timing of any future dividends; information systems failures and cyberattacks; our ability to consummate and successfully integrate acquisitions; and amounts for cash and non-cash charges related to restructuring plans that may differ from original estimates, including because of timing changes associated with the underlying actions.

Överträdelser kan leda till flera miljoner dollar i böter och fängelsestraff för enskilda personer. Bara förekomsten av konkurrensbegränsande beteende kan leda till att företag och enskilda personer anklagas för antitrustbrott. Avients personal bör alltjämt ta hänsyn till utländska lagar och förordningar i fråga om antitrust.

Once a specific resin has been identified for your needs, you can check in the table whether Avient has already concentrates listed for the corresponding supplier and under which conditions of use (minimum thickness, exact rating and maximum let-down ratio). ONCOLOR™ UL 94 COLORANTS HOW TO USE THE TABLES UL HB GENERIC RESIN TYPE FLAME RATING MINIMUM THICKNESS (MM) MAXIMUM LET-DOWN RATIO Acetal Copolymer (POM) HB 1.50 1:20 Acrylonitrile Butadiene Styrene (ABS) HB 1.50 1:10 Ethylene Propylene Thermoplastic Rubber (EPTR) HB 1.50 1:20 High Impact Polystyrene (HIPS) HB 1.50 1:10 Liquid Crystal Polymer (LCP) HB 0.83 1:10 Polyamide (PA) HB 3.20 1:33 Polyamide (PA66 and PA 4/6) HB 0.81 1:20 Polyamide 6 (PA6) HB 0.75 1:25 Polyamide 66 (PA66) HB 0.40 1:40 Polybutylene Terephthalate (PBT) HB 0.81 1:20 Polybutylene Terephthalate/Polycarbonate (PBT/PC) HB 1.50 1:10 Polycarbonate (PC) HB 1.50 1:15 Polycarbonate/Acrylonitrile Butadiene Styrene (PC/ABS) HB 1.50 1:20 Polycarbonate/Polyethylene Terephthalate (PC/PET) HB 1.50 1:20 Polyethylene (PE) HB 1.50 1:50 Polyethylene Terephthalate (PET) HB 0.80 1:16.7 Polyketone HB 1.50 1:20 Polymethyl Methacrylate (PMMA) HB 3.00 1:25 Polypropylene (PP) HB 1.50 1:15 Polystyrene (PS) HB 0.83 1:15 Polyurethane (PUR) HB 1.50 1:25 Polyvinylchloride (PVC) HB 1.50 1:20 Styrene Acrylonitrile (SAN) HB 1.50 1:20 Thermoplastic Elastomer (TPE) HB 0.75 1:25 UL 94 V-0, V-1, V-2 ASCEND GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polyamide 66 (PA66) 21X1(a)(f2), 21SPC1(a)(f2), 21SPF1(a)(f2), 21SPG1(a)(f2), 21SPM1(a)(f2), 20NSP1(a)(f2) 0.75 V-2 1:40 22HSP(e) 0.75 V-2 1:40 64C-R 3.0 V-2 1:50 ECO366(e) 0.4 V-0 1:40 ECO366H(e) 0.2 V-0 1:25 FR350J 0.4 V-0 1:25 20NSP(a)(f2), 21SPF(a)(f2), 21SPM(a)(f2), 21SPC(a)(f2) 0.4 V-2 1:40 20NSP(a)(h)(f2), 21SPF(a)(h)(f2), 21SPM(a)(h)(f2), 21SPC(a)(h) (f2) 1.5 V-2 1:20 Polyamide 66/6 (PA66/6) ECO315(e), ECO315J(e) 0.4 V-0 1:40 M344 3.0 V-0 1:25 909 0.75 V-0 1:25 UL 94 V-0, V-1, V-2 BASF GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polyamide 6 (PA6) 8202(t1), 8202 Blend (t1) 0.71 V-2 1:25 8202C(t1), 8202C BLEND (t1) 1.50 V-2 1:25 8202CHS(t1) (t3), 8202C HS Blend 1.50 V-2 1:25 8202HS(t1) 1.50 V-2 1:25 B3S 0.80 V-2 1:25 1.50 V-2 1:25 B3S Q661 1.50 V-2 1:25 B3S R03 1.50 V-2 1:25 8232G HSFR(t9), B3U10G5 (t9) 1.50 V-0 1:25 Polyamide 6/66 (PA6/66) C3U (m) 0.40 V-0 1:25 KR4205(m), C3U (m), C3U (t)(m) 0.40 V-0 1:25 KR4205, C3U 0.40 V-0 1:25 Polyamide 66 (PA66) 1000(b), 1310-(b), Ultramid A3K Q603(+) 1.50 V-2 1:10 A3K (o) Q790(g)(f2) 0.41 V-2 1:20 A3K(f2), A3K Q601(f2) 0.41 V-2 1:20 A3SK 0.41 V-2 1:25 A5 3.00 V-2 1:33 A3W(f1), A3W FC (f1) 0.75 V-2 1:10 A3K R01 (t)(g)(f2) 0.40 V-2 1:20 Polybutylene Terephthalate (PBT) B4406 G2 (o) Q798 1.50 V-0 1:20 B4406 G2(a), B4406 G2 (o) Q717(a) 1.50 V-0 1:20 B4406 G3 (o) Q798 1.50 V-0 1:20 B4406 G3(a), B4406 G3 (o) Q717(a) 1.50 V-0 1:20 B4406 G4 (o) Q798 1.50 V-0 1:20 B4406 G4(a2), B4406 G4 (o) Q717(a2) 1.50 V-0 1:20 B4406 G6 (o) Q798 3.00 V-0 1:12.5 B4406 G6(%) 1.50 V-0 1:20 B4406 G6(a1), B4406 G6 (o) Q717(a1), B4406 G6 (o) Q717 High Speed(a1) 1.50 V-0 1:20 B4406(a), B4406 (o) Q717(a) 1.50 V-0 1:20 B4406@ 1.50 V-0 1:20 B4450 G5, B4450 G5 (t) 0.40 V-2 1:50 Polyurethane (PUR) 11 85 A(a) FHF 000 (f2) 0.75 V-0 1:33 UL 94 V-0, V-1, V-2 CELANESE GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Liquid Crystal Polymer (LCP) A130(+), MT1310 1.50 V-0 1:40 Polyamide (PA) 132F(+)(f1), 135F(+)(f1) 0.75 V-2 1:20 HTNFR42G30NH 0.40 V-0 1:25 Polyamide 6/12 (PA6/12) 151, 151L 1.50 V-2 1:25 Polyamide 66 (PA66) A3 GF 25 V0XI 0.40 V-0 1:25 101(r9)(f1), 101F(r9)(f1), 101L(r9)(f1) 0.75 V-2 1:20 103FHS(+), 103HSL(+) 0.75 V-2 1:20 FR50(+)(f1) 0.35 V-0 1:20 FR7025V0F(+) 0.50 V-0 1:33 Polyamide 66/6 (PA66/6) FR72G25V0 0.80 V-0 1:25 Polyamide 66/6T (PA66/6T) FR95G25V0NH 0.40 V-0 1:25 HTNFR52G30BL(r3) 0.75 V-0 1:33 HTNFR52G30L(+), HTNFR52G30(+) 0.75 V-0 1:33 HTNFR52G30NH(r6) 0.40 V-0 1:25 0.75 V-0 1:10 HTNFR52G35BL 0.75 V-0 1:25 HTNFR52G35(+), HTNFR52G35 0.75 V-0 1:33 Polyamide 6T/ MPMDT HTNFR51G35L(+) 0.81 V-0 1:33 Polybutylene Terephthalate (PBT) 2016(b) 1.50 V-0 1:20 3116(b) 1.50 V-0 1:20 3216(b) 1.50 V-0 1:20 3316(b) 1.50 V-0 1:20 3316HF 1.50 V-0 1:20 LW9030FR 1.50 V-0 1:25 T841FR (r4) 1.50 V-0 1:25 Polyethylene Terephthalate (PET) FR530(l)(+)(f1), FR530L(l)(+)(f1) 0.75 V-0 1:25 Thermoplastic Elastomer (TPE) HTR8068 1.60 V-0 1:25 UL 94 V-0, V-1, V-2 DOMO GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polyamide (PA) J 60X1 V30 0.40 V-0 1:25 Polyamide 6 (PA6) PSB 286 0.80 V-2 1:25 3.00 V-2 1:25 S 60X1 V30 0.75 V-0 1.25 Polyamide 66 (PA66) A 205F(r4) 0.38 V-2 1:25 A 225F 0.75 V-2 1:25 A 50H1 (r3)(f2) 0.40 V-0 1:25 A 30G1 0.40 V-0 1:25 COVESTRO GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polycarbonate (PC) 2407 + (z)(f1) 0.75-2.60 V-2 1:10 2807 + MAS183 0.75 V-2 1:25 6455 + (z) 3.00 V-0 1:25 1.50 V-2 1:25 6485 + (z)(f1) 1.50 V-0 1:25 Polycarbonate/ Acrylonitrile Butadiene Styrene (PC/ABS) FR110 + 1.50 V-0 1:33 FR3005 HF + (z), FR3005 HF + BBS314 1.50 V-0 1:12.5 FR3010 + (z) 3.00 V-0 1:25 1.50 V-0 1:25 FR3010 HF + 3.00 V-0 1:25 FR3030 + 3.00 V-0 1:25 UL 94 V-0, V-1, V-2 ENVALIOR GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polyamide 46 (PA46) TE250F6(h1)(j) 0.50 V-0 1:25 Polyamide 6 (PA6) F223-D(f1), F223-D /A(f1) 0.75 V-2 1:25 K222-KGV5(f1) 0.75 V-2 1:16.7 1.50 V-2 1:16.7 K-FKGS6/B(f1)(y) 0.80 V-0 1:25 Polyamide 66 (PA66) SG-KGS6/HV 0.75 V-0 1:25 Thermoplastic Elastomer (TPE) PL460-S 1.60 V-0 1:25 Polyamide 4T (PA4T) T11 (h) 0.40 V-0 1:20 UL 94 V-0, V-1, V-2 EXXONMOBIL LANXESS GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Ethylene Propylene Thermoplastic Rubber (EPTR) 251-80W232(f7) 1.50 V-2 1:20 251-92W232 1.50 V-0 1:20 251-70W232 1.50 V-0 1:10 1.00 V-2 1:10 GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polyamide 6 (PA6) B30S+(f1) 1.50 V-2 1:25 B31SK+ 1.50 V-2 1:25 Polybutylene Terephthalate (PBT) B4235+ 1.50 V-0 1:10 TP364-302+, BF4232+(f1) 0.75 V-0 1:25 UL 94 V-0, V-1, V-2 SABIC GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polybutylene Terephthalate (PBT) 310(w) 1.50 V-0 1:20 310SE0(w) 1.50 V-0 1:20 310SE0(w),310SE0R(w) 1.50 V-0 1:20 420SE0(f1)(w)(GG)(rr1) 1.50 V-0 1:20 420SE0(f1)(w)(GG)(rr2) 1.50 V-0 1:20 457(w) 1.50 V-0 1:20 457(w), 451(w) 1.50 V-0 1:20 553(a)(f1)(w) 1.50 V-0 1:20 553(a)(f1)(w), 553E(a)(f1)(w), 553U(a)(f1)(w) 1.50 V-0 1:20 553(w)(f1), 553M(w)(f1) 1.50 V-0 1:20 DR48(w) 1.50 V-0 1:20 DR48,DR48M 1.50 V-0 1:20 V4760(a2) 0.40 V-0 1:20 EXVX1259, ENH4550 0.40 V-0 1:20 771 0.75 V-0 1:25 Polybutylene Terephthalate/ Polycarbonate (PBT/PC) 357(f1)(w)(IC), 357M(f1)(w)(IC), 357U(f1)(w)(IC) 1.50 V-0 1:20 357(f1)(w)(IC), 357U(f1)(w)(IC) 1.50 V-0 1:20 357X(f1) 1.50 V-0 1:20 V3900WX(GG)(f1)(IA), V3901WX(GG)(f1)(IA) 3.00 V-0 1:20 1.50 V-0 1:20 357(w)(f2)(IC), 357M(w)(f2)(IC), 357U(w)(f2)(IC) 1.50 V-0 1:20 UL 94 V-0, V-1, V-2 SABIC GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polycarbonate (PC) 221(f2) 1.50 V-2 1:25 221R(f2) 1.50 V-2 1:25 500(f2), 500R(f2) 3.00 V-0 1:33 503(f1) 3.00 V-0 10:1 1.50 V-0 10:1 503(f1), 503R(f1) 3.00 V-0 10:1 1.50 V-0 10:1 943(ab) 1.50 V-0 1:20 943(f1) 1.50 V-0 1:20 943(f1), 923(f1) 1.50 V-0 1:20 950A, 920ASR, FXD911A(GG), 940ASR 1.50 V-2 1:25 CFR7630(f1)(gg*) 1.50 V-0 1:25 ML5139R(f2) 3.00 V-0 1:33 950A, FXD911A(GG), 940ASR 3.00 V-0 1:25 943 1.50 V-0 1:20 920A 3.00 V-0 1:25 1.50 V-2 1:25 Polycarbonate/ Acrylonitrile Butadiene Styrene (PC/ABS) C2950 1.50 V-0 6:100 C6200(GG) 2.00 V-0 1:20 Acrylonitrile Styrene Acrylate/ Polycarbonate (ASA/PC) HRA222 (GG) 0.80 V-2 1:20 UL 94 V-0, V-1, V-2 SOLVAY (SYENSQO) OTHERS GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO Polyphenyl Sulfone (PPSU) R-5100 (r1)(##), R-5000 (r1)(##) 1.50 V-0 1:10 Polyphthalamide (PPA) AFA-4133 V0(+) (*) 0.75 V-0 1:25 BASE RESIN MANUFACTURER GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO ALBIS Polypropylene (PP) PP 13 CV2 14 1.50 V-2 1:25 AVIENT Polyvinylchloride (PVC) M3700(X), M3755(X) 1.50 V-0 1:25 M3900 1.50 V-0 1:25 CHI MEI Acrylonitrile Butadiene Styrene (ABS) PA-765(+) 1.50 V-0 1:10 Polycarbonate/ Acrylonitrile Butadiene Styrene (PC/ABS) PC-510(+) 1.50 V-0 1:25 EMS-CHEMIE Polyamide 6 (PA6) Grilon A 26 V0 0.75 V-0 1:25 FORMOSA Polycarbonate (PC) #1700+(f2) 0.36-0.42 V-2 1:50 GEON Polyvinylchloride (PVC) 85891(f1) 1.70 V-0 1:20 85891(f2) 1.70 V-0 1:20 M3700(X) 1.50 V-0 1:25 M3900 1.50 V-0 1:10 1:25 INEOS Polystyrene (PS) 855 HV 3.00 V-1 100:4 INVISTA Polyamide 66 (PA66) FRU4800 XHL (r1) 0.40 V-0 1:25 U4820L (r1) 0.40 V-2 1:25 UL 94 V-0, V-1, V-2 OTHERS BASE RESIN MANUFACTURER GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO KINGFA Polyamide 66 (PA66) PA66-R11G25 (##) 0.25 V-0 1:25 KURARAY Polyamide 9T (PA9T) GP2300S 0.40 V-0 1:25 LG CHEM Polycarbonate/ Acrylonitrile Butadiene Styrene (PC/ABS) LUPOY GP-5106-F 3.00 V-0 1:20 LOTTE CHEMICAL Acrylonitrile Butadiene Styrene (ABS) VH-0800(+) 1.50 V-0 1:25 Polycarbonate (PC) HN-1064(+) 0.75 V-2 1:10 1.50 V-0 1:10 1.20 V-1 1:10 Polystyrene (PS) VH-1800+ 3.00 V-0 1:25 1.50 V-0 1:25 MITSUBISHI Polycarbonate (PC) S-2000+(f1) 1.50-1.80 V-2 1:10 POLYMER PRODUCTS Polystyrene (PS) ZYNTAR 351 2.00 V-0 1:20 1.50 V-0 1:20 ZYNTAR 7000 2.00 V-0 1:25 ZYNTAR 702 2.00 V-0 1:25 8020 2.00 V-0 1:20 8120 2.00 V-0 1:20 8130 1.50 V-0 1:20 POLYMER RESOURCES Polycarbonate (PC) PC-FR1A-D, PC- FR2A-D, PC-FR3A-D 3.00 V-0 1:33 1.50 V-2 1:33 SUMITOMO Liquid Crystal Polymer (LCP) E6007LHF(ra) 0.30 V-0 1:25 E6007LHF-MR(gt) 0.20 V-0 1:12.5 UL 94 V-0, V-1, V-2 OTHERS BASE RESIN MANUFACTURER GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING MAXIMUM LET-DOWN RATIO TORAY Polyamide 6 (PA6) 1017 1.60 V-2 1:16.5 Polyamide 66 (PA66) 3004-V0(rr), CM3004-V0(rr) 0.40 V-0 1:25 TRINSEO Polycarbonate (PC) 891(w) 1.10 V-0 1:25 WELLMAN Polyamide 66/6 (PA66/6) 220-N, 21L-N, 22L-N 1.50 V-2 1:25 WESTLAKE Polyvinylchloride (PVC) 6597(f1), HF-6597(f1) 1.50 V-0 1:25 SP-7107 (f1)(a) 3.00 V-0 1:25 5VA AND 5VB BASE RESIN MANUFACTURER GENERIC RESIN TYPE SPECIFIC BASE RESIN MINIMUM THICKNESS (MM) FLAME RATING COLORS MAXIMUM LET-DOWN RATIO AVIENT Polyvinylchloride (PVC) M3900 1.50 5VB ALL 1:25 WHITE 1:10 CELANESE Polyamide 66/6T (PA66/6T) FR95G25V0NH 1.50 5VA ALL 1:25 Polybutylene Terephthalate (PBT) LW9030FR 2.00 5VA BLACK 1:25 3.00 5VA ALL 1:25 SK642FR 1.50 5VA BLACK 1:25 COVESTRO Polycarbonate/ Acrylonitrile Butadiene Styrene (PC/ABS) FR3010 + (z) 3.00 5VA ALL 1:25 GEON Polyvinylchloride (PVC) M3900 1.50 5VB ALL 1:25 WHITE 1:10 SABIC Polybutylene Terephthalate/ Polycarbonate (PBT/PC) V3900WX(GG)(f1)(IA), V3901WX(GG)(f1)(IA) 3.00 5VA ALL 1:20 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

Color, Color and More Color Manufacturers of equipment and apparel agree—a crisp pop of bright color adds just the right amount of visual interest needed to grab attention. A New Generation of Enthusiasts The ranks of shootings sports aficionados have grown in recent years, due in part to the burgeoning interests of millennials and non-traditional enthusiasts.

Those interested in registering for the event can do so at www.avient.com/investors.

Interested?