Factors that could cause our actual results to differ materially from those implied by forward-looking statements are described in detail in Part l of the Form 10-K. Khandpur President and CEO 2024 Performance & Highlights Sales: $3.24B +3% GAAP EPS: $1.84 Adjusted EPS(1): $2.66 +13% Adjusted EBITDA(1): $526M +5% Adjusted EBITDA Margin(1): 16.2% +20bps Dividend Increase: 14 Consecutive Years Great Place to Work® Certification 6 Consecutive Years (1)Reconciliations of these measures to the most directly comparable generally accepted accounting principles (GAAP) financial measures are included in this annual report on a supplemental page that follows the Form 10-K. THIS PAGE IS NOT PART OF AVIENT’S FORM 10-K FILING THIS PAGE IS NOT PART OF POLYONE’S FORM 10-K FILINGTHIS PAGE IS NOT PART OF POLYONE’S FORM 10-K FILINGTHIS PAGE IS NOT PART OF AVIENT’S FORM 10-K FILING Reconciliation of Non-GAAP Financial Measures (Unaudited) (In millions, except for per share data) Senior management uses comparisons of adjusted net income from continuing operations attributable to Avient shareholders and diluted adjusted earnings per share (EPS) from continuing operations attributable to Avient shareholders, excluding special items, to assess performance and facilitate comparability of results.

Blackout” Periods: The Company’s announcement of its quarterly financial results almost always has the potential to have a material effect on the market for the Company’s securities.

Internal Testing Available • Physical • Rheological, thermal, and moisture analysis • Microscopy • Liquid, gas, and size exclusion chromatography • Atomic, infrared, and nuclear magnetic resonance spectroscopy • Flammability • X-ray diffractometry • Weathering (QUV & Xenon Arc) • Failure analysis APPLICATION DEVELOPMENT Avient has design, application development and degreed plastics engineers available to give our customers reliable and experienced guidance to help navigate the development process.

PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection speed • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low Mold design • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Increase mold temperature • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation Mold design • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Mold design Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Mold design Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase shot size • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase shot size • Increase injection rate • Increase packing pressure • Increase gate size Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS www.avient.com Copyright © 2020, Avient Corporation.

PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Mold design Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase shot size • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase shot size • Increase injection rate • Increase packing pressure • Increase gate size Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection speed • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low Mold design • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Increase mold temperature • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation Mold design • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Mold design Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time TROUBLESHOOTING RECOMMENDATIONS Note: These are general processing conditions.

Cut vent depths to 0.0007″–0.0015″ Draft Angle Maintain a minimum draft angle of 1° per side 4 Artisan Pre-Colored Thermoplastics Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Check thermocouples and heater bands Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel • Decrease injection speed Gate location and/or size • Relocate gate to non-stress area • Increase gate size to allow higher flow rate and lower molded-in stress Wet material • Check moisture.

PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Check thermocouples and heater bands Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel • Decrease injection speed Gate location and/or size • Relocate gate to non-stress area • Increase gate size to allow higher flow rate and lower molded-in stress Wet material • Check moisture.

Internal Testing Available • Physical • Rheological, thermal, and moisture analysis • Dielectric properties • Laser etching and welding • Microscopy • Liquid, gas, and size exclusion chromatography • Atomic, infrared, and nuclear magnetic resonance spectroscopy • Flammability • X-ray diffractometry • Weathering (QUV & Xenon Arc) • Failure analysis APPLICATION DEVELOPMENT Avient has design, application development and degreed plastics engineers available to give our customers reliable and experienced guidance to help navigate the development process.

Additional draft may be required for grained/textured surfaces. 4 Nymax Polymer Formulations Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion Brittleness Wet material • Check moisture.

The substance is used in powdered form in industrial settings only. Health risks through exposure to TiO2 in its powdered form are presumed to be extremely low since TiO2 is typically fully incorporated into the end product in which it is used. EU published the classification of titanium dioxide as a suspected carcinogen (category 2) by inhalation in certain powder forms under the CLP regulation.