https://www.avient.com/sites/default/files/2022-05/Compensation Committee Charter (REV 10-2019).pdf
Microsoft Word - Compensation Committee Charter (REV 10-2019)3[1].docx
AVIENT CORPORATION
COMPENSATION COMMITTEE CHARTER
Membership
• The Committee will consist entirely of directors who meet the definition of “independent” as
set forth in the Corporate Governance Standards of the New York Stock Exchange, including
the additional independence requirements set forth in New York Stock Exchange Listed
Company Manual Section 303A.02(a)(ii)
Review and approve the terms of all employment agreements, management continuity
agreements and change in control agreements for elected officers.
3
Non-employee Director Compensation
The Committee shall evaluate whether any compensation consultant retained or to be
retained by it has any conflict of interest in accordance with Item 407(e)(3)(iv) of Regulation
S-K.
https://www.avient.com/sites/default/files/2021-03/avient-antitrust-2021-update-english.pdf
Avient’s legal department will help you protect yourself
and the Company should questions later arise.
3.
Avoid
even the appearance of any such agreement and avoid
circumstances where such agreements could occur.
3.
Document the incident, including
answers to the following: who was present at the
meeting, when and where the meeting occurred, and
what happened at the meeting.
8.
https://www.avient.com/investor-center/news/avient-hold-third-quarter-2024-conference-call
October 3, 2024
Oct. 3, 2024
8:00 a.m.
https://www.avient.com/knowledge-base/article/overmolding-processing
Clamp capacity should be 1.5 to 3 tons per square inch projected area
General-purpose screw with compression ratio of 2:1 to 3:1 can be used
Typical maximum residence time should be 8 - 10 minutes at processing temperature.
https://www.avient.com/sites/default/files/2021-03/avient-antitrust-2021-update-port-a4.pdf
Por isso, evite
contatos desnecessários com concorrentes.
3.
Evite até mesmo a aparência de tal
acordo e quaisquer circunstâncias em que esses
acordos possam ocorrer.
3.
Lista de verificação antitruste
8
Índice Política antitruste revisada em 2021
14.
https://www.avient.com/sites/default/files/2021-03/avient-antitrust-2021-update-esp-a4.pdf
Por este motivo, evite el contacto
innecesario con la competencia.
3.
Evite incluso la apariencia de cualquier
acuerdo de este tipo y evite circunstancias en las que
se puedan producir dichos acuerdos.
3.
Lista de verificación antimonopolio
8
Índice Política Antimonopolio revisada de 2021
14.
https://www.avient.com/sites/default/files/2021-03/avient-antitrust-2021-update-hun-a4.pdf
Ezért kerülje a felesleges kapcsolatot
a versenytársakkal.
2021. évi módosított trösztellenes szabályzat
4
Tartalomjegyzék
3.
Kerülje el az ilyen
megállapodásoknak még a látszatát is, és kerülje el
azokat a helyzeteket, amikor ilyen megállapodások
születhetnének.
3.
Trösztellenes ellenőrzőlista
8
Tartalomjegyzék 2021. évi módosított trösztellenes szabályzat
14.
https://www.avient.com/sites/default/files/resources/PolyOne%2520India%2520Terms%2520and%2520Conditions%2520of%2520Sale%2520of%2520Products.May%25202016.pdf
In no event will either party have liability to the
other for any incidental, consequential, exemplary or special damages.
3.
Buyer will reimburse Seller for all national, state, local or other taxes
(other than income taxes), excises or charges, and fees, which Seller must pay
in connection with the manufacture and supply of Product, but only those
amounts not already included in the price at the commencement of this
contract.
8.
Either party may suspend performance hereunder (except to
pay for Product already received) in the event of: (1) acts of God, fire,
explosion, flood, hurricanes; (2) strikes, lockouts or other industrial
disturbances or riots; (3) war, declared or undeclared, or acts of terrorism; (4)
compliance with any Federal, state, provincial, municipal or military law,
regulation, order, or rule, foreign or domestic, including priority, rationing,
allocation or preemption orders or regulations, or cancellation of Seller’s or
Buyer’s license to operate its plant; (5) catastrophic failure of facilities used
to manufacture Product, interruption or shortage of transportation, labor,
power, fuel or raw materials; (6) total or partial shutdown due to Seller’s
normal plant turnaround; or (7) any other cause or causes of any kind or
character reasonably outside the control of the party failing to perform,
whether similar or dissimilar from the enumerated causes (a “force
majeure”).
https://www.avient.com/products/thermoplastic-elastomers/tpe-knowledge-center/technical-bulletins/hardness-vs-thickness
3
3
Injection Molding: Troubleshooting
https://www.avient.com/resources/safety-data-sheets?page=5924
NM GF 633 HS Green Conc 3%
NM GF 633 HS Gray Conc 3%
PP FR 8-6 LMS-1000