It has good tensile, thermal, flex, and impact properties like nylon (PA), while maintaining the excellent wear, chemical resistance, and dimensional stability of acetal (POM). If the material is allowed to stay in an injection molding machine or extruder (profile, sheet, etc.) too long, the material will start to discolor and brown ‘freckles’ may appear.  Are UV protection and/or flame retardant packages available?

Ejector Pin Design Guidelines When designing ejector pins, the following guidelines should be used, which can be seen in figure 42. If the material is shear-sensitive, consult the material data sheet or processing guide for instructions to set recovery time • The cooling time should only be 1–2 seconds longer than the screw recovery time, unless dictated by dimensional stability or part thickness Minimize Clamp Pressure This step is done to reduce the amount of energy used by the machine. • Reduce the clamp tonnage until flash is seen around the parting line, then increase the clamp tonnage by 5-10% Minimize Cycle Time • Mold Open/Close – Should be as fast as possible, without slamming, and still produce a nice fluid motion • Ejector Speed – As fast as possible, without influencing part quality • Ejector Stroke – Only stroke the ejectors as many times as needed to separate the part from the core - i.e. Note: Once the process has been established, the parts should be tested for dimensional stability over the range of service termperatures.

These grades combine excellent chemical resistance and dimensional stability with improved wear resistance and low coefficient of friction (COF) properties. The formulations can also be customized to meet specific application needs, such as improved UV stability. KEY CHARACTERISTICS • Inherently low COF • Excellent wear resistance • Excellent chemical resistance • Low moisture uptake • Excellent dimensional stability • Cost-effective • Eco-conscious alternative to PA66, PA6 and POM MARKETS & APPLICATIONS These materials are ideal for use in applications requiring lubricated solutions, as the formulations have improved wear, chemical, and hydrolysis resistance over nylons (PA6 or PA66).

Available with 10–40% short glass fiber fillers, these formulations provide superior chemical resistance, low moisture uptake, excellent dimensional stability, and high impact and wear resistance. The formulations can also be customized to meet specific application needs, such as improved UV stability. KEY CHARACTERISTICS • Excellent chemical resistance • Low moisture uptake • Comparable dimensional stability to nylon • Reinforced with 10–40% short glass fiber • High impact and wear resistance • Cost competitive • Eco-conscious alternative to PA66 and PA6 • Non-halogen, flame retardant performance MARKETS & APPLICATIONS These glass-reinforced materials meet the challenges found in chemical, fuel contact, and high moisture environments. • Industrial – pipes, tubing, fluid management • Electrical/Electronics – connectors, battery components • Transportation – under-the-hood fuel/ chemical components PRODUCT BULLETIN PROPERTY COMPARISON — EDGETEK™ PKE FORMULATIONS VS NYLON 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

Operating Globally, Serving Locally — As a truly global company, we have operations and technical expertise around the world to efficiently serve our customers…wherever they may need us. It’s why we win. 11 474 644 924 107 147 208 467 616 872 2014 2018 2020PF R&D / Technical Marketing Sales Commercial Resources + 36% + 37% + 32% + 43% + 41% + 42% Headcount figures are Pro forma for the sale of Designed Structures and Solutions (DSS) and Performance Products and Solutions (PP&S) segments and the acquisition of the Clariant Masterbatch business. 2020PF data as of August 31, 2020. Avient Total Enterprise Value Pro forma for acquisition of Clariant Masterbatch business and tax payments associated with the PP&S divestiture per Company filings, resulting in a cash adjustment from the June 30, 2020 balance sheet of ~$1,520MM 2.

KEY CHARACTERISTICS • Intended for use in a variety of thermoset epoxy systems • Based on heat stability, lightfastness, weatherability and toxicity • Use level is 1%–2% for thick casting and 5%–10% for a thin coating APPLICATIONS Stan-Tone EPX dispersions are suitable for use in a variety of applications, including: • Protective coatings • Adhesives • Epoxy flooring • Electrical potting • Composites • Laminates Stan-Tone Code Pigment Type Approx. % Pigment Specific Gravity Color Index Lightfastness WHITE 10EPX03 Titanium Dioxide, Rutile 57 1.95 PW-6 I/O YELLOW 12EPX01 Diarylide AAOT GS 25 1.22 PY-14 I 12EPX03 Diarylide HR RS 20 1.2 PY-83 I/O (Mass) 13EPX02 Isoindolinone RS 30 1.3 PY-110 I/O 13EPX03 Benzimidazolone GS 40 1.27 PY-151 I/O (Mass) 81EPX01 Iron Oxide 40 1.62 PY-42 I/O ORANGE 15EPX03 Benzimidazolone 30 1.26 PO-36 I/O RED 23EPX04 Quinacridone BS 25 1.21 PV-19 I/O 23EPX06 Specialty Naphthol BS 30 1.21 PR-170 I/O (Mass) C 25EPX01 Red 2B, Ca Salt Bs 24 1.27 PR-48:2 I/O (Mass) 28EPX01 Red 2B, Ba Salt YS 23 1.29 PR-48:1 I/O (Mass) 82EPX01 Iron Oxide, Light BS 40 1.67 PR-101 I/O 82EPX02 Iron Oxide, Dark BVS 40 1.68 PR-101 I/O 82EPX04 Iron Oxide, Light VYS 40 1.67 PR-101 I/O BLUE 40EXP03 Phthalocyanine GS 25 1.25 PB-15:3 I/O 40EXP05 Phthalocyanine RS 25 1.25 PB-15:3 I/O 42EXP02 Ultramarine 50 1.54 PB-29 I/O 49EXP01 Cobalt 50 1.83 PB-28 I/O GREEN 50EPX02 Phthalocyanine BS 18 1.34 PG-7 I/O 50EPX03 Phthalocyanine YS 25 1.42 PG-7 I/O 59EPX01 Chromium Oxide 40 1.64 PG-17 I/O VIOLET/MAGENTA 24EPX03 Quinacridone Violet 15 1.2 PV-19 I/O 24EPX04 Ultramarine Violet 50 1.66 PV-15 I/O 24EPX05 Quinacridone Magenta 20 1.21 PR-122 I/O 24EPX06 Benzimidazolone 20 1.2 PV-32 I/O 24EPX07 Carbazole Violet 15 1.2 PV-23 I/O BROWN/TAN 83EPX01 Iron Oxide, Light 39 1.64 PBr-6 I/O 83EPX02 Iron Oxide, Dark 40 1.66 PBr-6 I/O BLACK 90EPX01 Furnace - High Jet 14 1.23 PBk-7 I/O 90EPX04 Furnace - Medium 20 1.25 PBk-7 I/O 90EPX05 Iron Oxide 50 1.77 PBk-11 I/O EPX RS = Red Shade YS = Yellow Shade VYS = Very Yellow Shade BS = Blue Shade VBS = Very Blue Shade GS = Green Shade HR = Heat-Resistant LIGHTFASTNESS I = Indoor Only I/O = Indoor or Outdoor Mass = Outdoor Masstone Application Only C = Some Caution Advised www.avient.com Copyright © 2020, Avient Corporation.

Colorant Chromatics FEP UV Laser Marking Product Bulletin_CN8.29-1

CESA Nofog Plus Product Bulletin_CN12.15-1

TPEE AND TPU FILM MANUFACTURER H O T M E L T A D H E S I V E F I L M • Eliminate anti-phenol yellowing after storage • Maintain natural color of product • Demonstrate no impact on melt flow ability • Prevented yellowing after storage to provide a quality appearance • Had no negative impact on the product’s mechanical properties • Extended the shelf life and durability of the product Cesa Anti-phenolic Yellowing Additive KEY REQUIREMENTS WHY AVIENT? All Rights Reserved https://www.avient.com/products/polymer-additives/surface-modifier-additives/cesa-anti-phenolic-yellowing-additives Slide 1: TPEE and TPU Film MANUFACTURER

Cesa™ Anti-fog Plus Additives for Multilayer Films We buy with our eyes and this is no truer than wanting to see the food we purchase, especially fresh perishable foods.Cesa™ Anti-fog Plus solutions are the next generation additives, which work in both hot and cold fog conditions and in mono and multilayer film, to keep food attractive for longer. Thanks to a unique combination of multi-additives in the masterbatch formulation, Cesa Anti-fog Plus materials allow good fog clearance before and after lamination, provide quick performance in both hot and cold conditions. KEY CHARACTERISTICS Cesa Anti-fog Plus additives help packaging to retain clarity, maintaining an excellent balance of immediate and long-lasting effects under both hot and cold conditions in mono and multilayer film.