If a tote should get damaged by a forklift or in transport, the doors, locks and handles can all be replaced. 

The pre-mix colors are getting too expensive to re-order. Once a shop gets in the routine of the mixing system, the savings on labor, waste and purchasing is nearly immediate.

Parameters NM5600-8002 RS NM5600-8004 RS Drying Temperature 100–120°C 100–130°C Drying Time 4–6 hours 4–6 hours Barrel Temperature °C °C Rear Zone 250–270 260–270 Central Zone 260–280 270–290 Front Zone 270–295 290–305 Nozzle 290–300 290–300 Mold Temperature 80–100 80–100 Screw Speed Moderate Moderate Back Pressure 3–10bar 3–10bar Cushion stroke 5–10% of plasticizing stroke 5–10% plasticizing of stroke Injection Speed Medium Medium Injection Pressure Medium–high Medium–high Holding Pressure 30–50% of injection pressure 20–40% of injection pressure Screw Type General purpose General purpose Screw L/D 20:1 20:1 Screw Compression Ratio 2.5:1 2.5:1 Non-return Check Valve Free flow check ring Free flow check ring Nozzle Type Reverse taper Reverse taper Barrel Capacity 30–80% of barrel should be used Processing Guide 2 Start Up & Shut Down Recommendations Purge Compound 1. 2–3 melt flow PP or purging compound. Each 90° bend in the system should step down in size. 4.

Processing Guide 3 Start Up & Shut Down Recommendations Purge Compound HDPE or HIPS Recycling Recycling Therma-Tech™ up to 20% is permissible. Step each 90° bend in the system down in size (from sprue to gate) approximately 1.5mm (1/16") to reduce pressure drop. 5.

RECYCLABILITY METHOD-1 • Preforms were produced by dosing 0.09% of Avient Fortis Amber-1 and 4% of our nylon- based oxygen scavenger Amosorb SolO2-2 • Preforms were ground down to a coarse granule size (~2mm) using a Retsch mill. • The coarse ground material was then crystallized in a vacuum oven at 160°C before drying the material at 160°C for approx. 4 hours within a PET drier • Plaques were then molded on a BOY XS and 10 of these were kept after each cycle, to take color measurements • This process was then repeated until 5 heat cycles had been completed RESULTS FOR RECYCLABILITY METHOD-1 As plaques were produced while the material went through five different melt heat histories, plaques were produced at each cycle and L*, a*, and b* values were measured. To do so the following procedure was carried out: • Preforms were produced by dosing 0.09% of Avient Fortis Amber-1 and 4% of our nylon- based oxygen scavenger Amosorb SolO2-2 • Preforms were ground down to a coarse granule size (~2mm) using a Retsch mill • The coarse ground preforms were crystallized in a vacuum oven at 160°C before drying the material in a PET drier at 160°C for approx. 4 hours • This material was then injection molded and blown into bottles with a) 50:50 dilution with Virgin PET with no color and b) 50:50 dilution with Virgin PET + Fortis Amber-1 at 0.045% Figure 2.

company-owned vehicles, process emissions, and on-site heating) Scope 2: Indirect emissions from purchased indirect sources, such as the production of electricity and steam for an organization’s use Scope 3: Indirect emissions from sources up and down the supply chain, including materials, transportation of goods, and the processing, use, and end-of-life treatment of sold products Cradle-to-Gate: Carbon impact of a product from raw materials and product manufacturing Cradle-to-Grave: Carbon impact and analysis across the entire life cycle of a product from raw materials to disposal © 2023 Avient • www.avient.com • 1.844.4AVIENT Raw Materials Supply Chain UNDERSTANDING CARBON FOOTPRINT CO2e Transportation End-of-Life Treatment Processing of Goods Use of Products Transportation Chemical Processing Cradle-to-Gate (B2B) Cradle-to-Grave (B2C) SCOPE 3 INDIRECT SCOPE 3 INDIRECT Electricity Steam Company Facilities Company-Owned Vehicles SCOPE 1 DIRECT SCOPE 2 INDIRECT Reporting CompanyUpstream

Do not get involved in circumstances that may provide or suggest the appearance of an agreement with a competitor. The more potentially damaging an action or statement is, the more likely it is that somebody else will write it down or remember it.

WithStand antimicrobial additives can be combined with colorants or other functional additives in a single masterbatch or liquid solution to get the exact performance needed.

And when they get there, they want devices that move with them and keep the new ‘dimension’ free from distractions.

We provide total support from design through production, including navigation of a complex regulatory environment, delivering solutions that let you get your products to market faster and with greater confidence.