PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Increase shot size • Increase injection rate • Increase packing pressure Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature TROUBLESHOOTING RECOMMENDATIONS Note: These are general processing conditions.

Footprint (LxW cm) 86 x 71 98 x 38 60 x 35 55 x 30 86 x 80 Typical max. throughput (kg/hr) 1000 625 250 50 120 Max. metering rate (cc/s) 10 10 10 1.8 1.25 Continuous use Yes Yes No No Yes Transfer pumps PC/Peri Peri NA NA PC Metering pumps PC/Peri PC/Peri PC/Peri Peri PC Interchangeable cassette Yes Yes Yes No Yes Typical PlanetPak delivery unit 25L 25L NA 1L 25L Other delivery packaging IBC/LN Drum/LN LN LN NA PC PUMP RATE (cc/rev) 0.09 0.28 0.87 2.6 5.2 RECOMMENDED OUTPUT RANGE (g/min) 0.9 to 9 2.8 to 28 8.7 to 87 26 to 260 53 to 520 PC PUMP MAX (g/min) 18 56 174 520 1040 CONTROLLER CMG 3000 FlexG CMG 5000 CMG 6000 Application Injection Molding Extrusion Melt Injection Volumetric/gravimetric V V (weight data) V/G V/G Data export/network No Yes Yes Yes Touch screen No Yes Yes Yes Multiple log-in levels No No Yes Yes FlexCart Model S Optional Yes No Mini Model S No Yes No Micro Yes No Yes No Nano Yes No No No Melt Injection No No No Yes Choosing a progressive cavity pump for transfer or metering Choosing the controller MAKING THE RIGHT CHOICE Here are the options which should be considered for an informed choice of combinations: (Note: LN = 3, 5 & 10L molded container PC = Progressing Cavity Pump Peri = Peristaltic Pump) Avient can provide support and assistance on every aspect of liquid color and additive processing.

Van Hulle Page 53 United States 33% 47% Canada Asia 12% Latin America Eastern 2% 2011 Revenue: $0.7 Billion*2011 Revenue: $0.7 Billion* SolutionsSolutions At a Glance Building & Construction 11% Wire & Cable 15% Consumer Packaging 36% Industrial 10% Misc. 7% HealthCare 3% Transportation Textiles Canada 1% Latin America 5% 2011 Revenue by Industry Segment*2011 Revenue by Industry Segment* *Pro forma for the acquisition of ColorMatrix Expanding ProfitsExpanding Profits 1.7% 4.6% 5.1% 5.5% 7.1% 9.6% 12-16% 2006 2007 2008 2009 2010 2011PF 2015 Operating Income % of Sales Target Page 54 Value Proposition • GCAI is a global leader enabling OEMs and converters to profitably expand their business with customized color and additive solutions Transformation Highlights • Mix improvement and value-based selling has Value Proposition and Transformation Highlights • Mix improvement and value-based selling has driven nearly 800 basis points increase in operating margin since 2006 • 2011 acquisition of ColorMatrix accelerates innovation pipeline and expansion into new markets > $12B Addressable Market Page 55 • Unbiased, solution-based culture selling value �Customer-centric approach � Economic value impact documented for customers • Complete package, product range and service offering �Custom solutions for customers’ unique requirements Key Differentiators �Custom solutions for customers’ unique requirements � Industry-leading service offering • Coordinated global infrastructure �Consistency in product and customer service � Supply-chain reliability Page 56 From Volume Commodity white dominated mix To Value Focus on specialty color Global Film Customer Volume Revenue Gross Margin $ Mix Transformation – Executing the Strategy 2010 2011 2010 2011 2010 2011 Page 57 Global Packaging Customer Volume Sales Gross Margin $ From Volume Commodity white dominated mix To Value Focus on specialty color Mix Transformation – Executing the Strategy 2010 2011 2010 2011 2010 2011 Page 58 • OnColor™ HC Plus � Applications: Medical devices � Customer benefits: Brand enhancement, expanded market opportunities, speed-to-market • WithStand™ Antimicrobial Solutions � Applications: Healthcare devices, appliances, kitchen utensils Key Innovations � Applications: Healthcare devices, appliances, kitchen utensils and surfaces, children’s toys � Customer benefits: Expanded market opportunities, extended product life • OnCap™ Antifog � Applications: Food packaging � Customer benefits: Extended shelf life, improved product aesthetics, production efficiencies Page 59 • $1.5 billion attractive, growing market • Additives improve performance and reduce cost through light-weighting, reduced waste, faster cycle times, and extended shelf life of finished product • Aligned with megatrend of protecting the environment Market Opportunity Shelf-life extension Greater product consistency Weight reduction Performance Additives the environment Leading Global Supplier of Additives In Fast Growing PET Market consistency Recyclability and reduced carbon footprint Color and special effects Enhanced product aesthetics High heat resistance 4% 4% 8% 9% 9% 10% 11% 14% Western North America South America MEA Easter Asia Pacific China India PET 2008-13P CAGR Page 60 HyGuardTM Oxygen Barrier System • Applications: Beverage containers, food packaging • Function: Active scavenging system for • Function: Active scavenging system for oxygen-barrier improvement • Customer benefits: Extended shelf-life, light-weight, recyclable Page 61 ExceliteTM Foaming Agent • Applications: Vinyl sheet for digital printing • Function: Chemical foaming agent for weight reduction • Customer benefits: Increased product quality, operational efficiencies Page 62 Joule RHBTM Advanced Reheat Technology • Applications: PET containers • Function: Infra-red absorber for improved • Function: Infra-red absorber for improved • Customer benefits: Sustainability, operational and energy savings reheating efficiency Page 63 • Accelerate customer development pipeline with OnColor™ HC Plus • Provide solutions addressing infection concerns in healthcare facilities Areas of Focus $8.7 $20.0 Healthcare 2006 2011PFconcerns in healthcare facilities • Help customers expand into new markets with HyGuard™ technology • Extend food shelf life and consumer appeal with OnCap™ Anti-Fog $130.2 $268.0 2006 2011PF Packaging 2006 2011PF (Revenue in $ millions) 2006 2011PF 2006 2011PF Page 64 Critical Imperatives and 2015 Goal Critical Imperatives • Integrate and leverage ColorMatrix technology and customer relationships • Identify and focus on specialty applications within our target markets • Accelerate global expansion and profitability improvements in emerging markets, leveraging success in U.S. and Europe 2015 Goal • 12 - 16% return on sales Page 65 Page 66

PolyOne Corporation Page 4 PolyOne Commodity to Specialty Transformation • Volume driven, commodity producer • Heavily tied to cyclical end markets • Performance largely dependent on non- controlling joint ventures 2000-2005 2006 - 2009 2010 – 2014 2015 and beyond • Steve Newlin appointed, Chairman, President and CEO • New leadership team appointed • Implementation of four pillar strategy • Focus on value based selling, investment in commercial resources and innovation to drive transformation • Substantial EPS growth from $0.13 to all-time high of $1.80 • Shift to faster growing, high margin, less cyclical end markets • Key acquisitions propel current and future growth, as well as margin expansion • Specialty mix expands to 65% of Operating Income – strongest mix of earnings in history • Accelerating growth • Deliver consistent double digit annual EPS growth • Maintain >35% vitality index • Pursue strategic acquisitions that expand specialty offerings and geographic breadth • Invest and grow current and next generation talent PolyOne Corporation Page 5 Building & 10% Electrical & 11% 9% Distribution 28% PP&S 52% 69% 13% 7% Asia 2014 Revenues: $3.8 Billion End Markets 2014 Revenues: $3.8 Billion PolyOne At A Glance $13 $31 $46 $46 $92 $96 $122 $195 $242 2006 2007 2008 2009 2010 2011 2012 2013 2014 Specialty Operating Income ($M) PolyOne Corporation Page 6 Old PolyOne *Operating Income excludes corporate charges and special items 2% 34% 43% 62% 65% 69% 0% 20% 40% 60% 80% 100% 2005 2008 2010 2013 2014 Q1 2015 2020 % o f O pe ra tin g In co m e* JV's Performance Products & Solutions Distribution Specialty 80%+ Specialty OI $5M $46M $87M $195M $242M $60M Mix Shift Highlights Specialty Transformation Transformation 2020 Platinum Vision Platinum Vision PolyOne Corporation Page 7 Confirmation of Our Strategy The World’s Premier Provider of Specialized Polymer Materials, Services and Solutions Specialization Globalization Operational Excellence Commercial Excellence PolyOne Corporation Page 8 -100% 0% 200% 300% 400% 500% 600% Strategy and Execution Drive Results $0.12 $0.27 $0.21 $0.13 $0.68 $0.82 $1.00 $1.31 $1.80 '06 '07 '08 '09 '10 '11 '12 '13 '14 ‘06-‘14 Adjusted EPS CAGR = 40% Adjusted EPS Share Price vs. S&P 500 PolyOne Corporation Page 9 2006 Q1 2015 2020 “Where we were” “Where we are” Platinum Vision 1) Operating Income % Specialty: Global Color, Additives & Inks 1.7% 16.2% 20%+ Global Specialty Engineered Materials 1.1% 16.3% 20%+ Designed Structures & Solutions 1.4% (2012) 2.7% 12 – 14% Performance Products & Solutions 5.5% 6.5% 10 – 12% Distribution 2.6% 5.9% 6.5 – 7.5% 2) Specialty Platform % of Operating Income 6.0% 69% 80%+ 3) ROIC 5.0% 11.4% 15% 4) Adjusted EPS Growth N/A 22 Consecutive Quarters of EPS Growth Double Digit Expansion Proof of Performance & 2020 Goals PolyOne Corporation Page 10 Platinum Vision: Pathway to Accelerated Growth Organic Sales Growth Margin Expansion Share Repurchases Acquisitions PolyOne Corporation Page 11 Innovation Drives Earnings Growth *Percentage of Specialty Platform revenue from products introduced in last five years $20 $53 2006 2014 Research & Development Spending ($ millions) Specialty Platform Vitality Index Progression* 14% 27% 2006 2014 Specialty Platform Gross Margin % 20% 44% 2006 2014 Specialty Vitality Index Target ≥ 35% PolyOne Corporation Page 12 Megatrends Aligned with Key End Markets Decreasing Dependence on Fossil Fuels Protecting the Environment Improving Health and Wellness Megatrend End Markets Globalizing and Localizing Health & Wellness Transportation Packaging Consumer PolyOne Corporation Page 13 Prototype Frame Opportunity Scale-up & Test Market Build Business Case Commercial Launch Phase 1 Phase 2 Phase 3 Phase 4 Phase 5 6 9 7 3 5 12 5 3 2 8 4 2 4 3 1 Breakthrough Platform Derivative A Rich Pipeline of Opportunity Number of Projects 14 8 18 12 22 74 Addressable Market ($ millions) $700 $600 $600 $1,900 PolyOne Corporation Page 14 60% 98% 20% 30% 40% 50% 60% 70% 80% 90% 100% 2008 Q1 2015 Pension Funding** As of March 31, 2015 Debt Maturities & Pension Funding Net Debt / EBITDA* = 2.1x $49 $317 $600 $0 $100 $200 $300 $400 $500 $600 $700 $800 2015 2020 2023 Debt Maturities As of March 31, 2015 ($ millions) Coupon Rate: 7.500% 7.375% 5.250% ** includes US-qualified pension plans only *TTM 3/31/2015 PolyOne Corporation Page 15 Free Cash Flow and Strong Balance Sheet Fund Investment / Shareholder Return  Expanding our sales, marketing, and technical capabilities  Investing in operational and LSS initiatives  ~75% of capital expenditures fund growth initiatives Organic Growth Acquisitions Share Repurchases Dividends $0.16 $0.20 $0.24 $0.32 $0.40 $0.10 $0.20 $0.30 $0.40 $0.50 2011 2012 2013 2014 2015 Annual Dividend  Targets that expand our: • Specialty offerings • End market presence • Geographic breadth  Synergy opportunities  Adjacent material solutions  Repurchased over 500k shares in Q1 2015  Repurchased 11.8 million shares since early 2013  8.2 million shares are available for repurchase under the current authorization PolyOne Corporation Page 16 PolyOne Core Values Innovation Collaboration Excellence PolyOne Corporation Page 17 The New PolyOne: A Specialty Growth Company Why Invest In PolyOne?  Addressable market exceeds $40 billion  Strong performance demonstrates that our strategy and execution are working  Megatrends and emerging opportunities align with our strengths  Innovation and services provide differentiation, incremental pricing power, and competitive advantage  Strong and proven management team driving growth and performance PolyOne Corporation Page 18 Appendix PolyOne Corporation Page 19 $0.17 $0.22 $0.24 $0.31 $0.44 $0.46 $0.00 $0.25 $0.50 Q1'10 Q1'11 Q1'12 Q1'13 Q1'14 Q1'15 Adjusted EPS $30 $34 $25 $30 $35 Q1 2014 Q1 2015 GCAI Operating Income (in millions) $18 $23 $15 $20 $25 Q1 2014 Q1 2015 GSEM Operating Income (in millions) Q1 2015 Financial Highlights  Global Specialty Engineered Materials’ operating margin of 16.3% above the 2015 target  Global Color Additives and Inks’ operating margin grew to 16.2%  First quarter adjusted EPS has grown on average 23% per year since 2010 +26% +11% PolyOne Corporation Page 20 Building & 7% Electrical & 1% 31% Textiles 7% 12% 1.7% 4.6% 5.1% 5.5% 7.2% 8.1% 9.7% 12.2% 16.2% 20%+ 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales At a Glance Global Color, Additives and Inks 2014 Revenues: $0.9 Billion Solutions Expanding Profits 2014 Revenue by Industry Segment 14.7% Platinum Vision 36% PolyOne Corporation Page 21 4% Building & 18% Electrical & 16% At a Glance Global Specialty Engineered Materials 2014 Revenues: $0.6 Billion Solutions 2014 Revenue by Industry Segment Expanding Profits 1.1% 1.3% 3.4% 5.1% 9.6% 8.0% 8.6% 9.3% 16.3% 20%+ 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales Platinum Vision 12.1% 33% 19% PolyOne Corporation Page 22 2% Building & 23% 27% 30% 96% At a Glance Designed Structures and Solutions Solutions 2014 Revenues: $0.6 Billion Expanding Profits 2014 Revenue by Industry Segment 1.4% 5.6% 7.3% 2.7% 12-14% 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales Platinum Vision PolyOne Corporation Page 23 Building & 33% 5% Electrical & 1% 11% 18% 16% 5.5% 6.9% 3.8% 3.6% 5.5% 4.3% 6.3% 7.2% 6.5% 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales At a Glance Performance Products and Solutions Solutions Expanding Profits 2014 Revenues: $0.8 Billion 10-12% Platinum Vision 2014 Revenue by Industry Segment 7.7% PolyOne Corporation Page 24 Building & 13% Electrical & 23% 15% 25% 2.6% 3.0% 3.5% 4.0% 4.6% 5.6% 6.4% 5.9% 5.9% 6.5-7.5% 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales 15% 50% 2006 Q1 2015 At a Glance Distribution Key Suppliers 2014 Revenues: $1.1 Billion ROIC Expanding Profits 6.1% Platinum Vision http://www.polyone.com/Pages/VariationRoot.aspx PolyOne Corporation Page 25 2 lbs Plastic = 3 lbs aluminum or 8 lbs steel or 27 lbs glass 33% less material by weight than aluminum 75% less material by weight than steel 93% less material by weight than glass Requires 91% less energy to recycle a pound of plastic versus a pound of paper Source: SPI: Sustainability and the Plastics Industry Plastics: Key to Future Sustainable Development PolyOne Corporation Page 26 Commitment to Operational Excellence 81% 93% 2006 2014 16.2% 9.9% 2006 2014 On-Time Delivery Working Capital % of Sales 5% 43% 2006 2014 Percent of Associates Trained in LSS  Four consecutive years – CFO Magazine Best Working Capital Management in the chemical industry World’s Best Business Process Excellence Program in 2012*  103 trained Black Belts  247 trained Green Belts  127 trained Kaizen Leaders World’s Best Start-up Program for Lean Six Sigma Deployment in 2009* *Both awards received from International Quality and Productivity Center PolyOne Corporation Page 27 Application Examples PolyOne Corporation Page 28  $1.5 billion attractive, growing market  Additives improve performance and reduce cost through light-weighting, reduced waste, faster cycle times, and extended shelf life of finished product  Aligned with megatrend of protecting the environment:  Sustainability benefits include lower package weight and improved recyclability of package at end of use Market Opportunity Leading Global Supplier of Additives In Growing PET Market Shelf-life extension Greater product consistency Recyclability and reduced carbon footprint Color and Special Effects Weight reduction Enhanced product aesthetics High heat resistance PET Bottling Technology 0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 2009 2014 2019 Asia Pacific North America Latin America Western Europe Eastern Europe Middle East and Africa Global PET Packaging Growth 2009-2019 Source: Euromonitor retail off-trade consumption (PET bottles & jars, home care, personal care, food & non-alcoholic beverages) B ill io n un its 5% CAGR PolyOne Corporation Page 29 • Includes formulation and consultative services to assist manufacturers and brand owners in positively identifying their finished goods • Protects brand equity & consumer welfare • Reduces exposure to unwarranted recall expenses • Secures supply chain integrity – support for safe expansion into new geographies Authentication Technology PolyOne Corporation Page 30 • Color harmonization across 15 unique color-and-polymer combinations • Eliminated need for multiple pre- colored materials • Reduced Land Rover’s working capital 2015 Range Rover Evoque Interior PolyOne Corporation Page 31 • Reduced health and environmental impact • System cost reduction • Radiation-shielding performance • Parts consolidation • Design freedom CT Scanner PolyOne Corporation Page 32 Metal Replacement Solutions • Replaces metal in LED lighting • Extends LED durability and life span eliminating hot spots • Greater design flexibility with fewer parts • Weight reduction • Simplifies manufacturing and lowers total production cost PolyOne Corporation Page 33 Next Generation Solar Charger • Ginkgo Solar Tree charger utilizing our unique reSound™ material • reSound™ is a durable material consisting of 50% bio-derived plastic and 50% traditional petroleum-based plastic • Use of reSound™ reduced the carbon footprint for this product by 35% • reSound™ Is classified as a PolyOne Sustainable SolutionSM PolyOne Sustainable SolutionSM PolyOne Corporation Page 34 High-Barrier Packaging Containers • Capability to extrude up to 13 layers • Strong oxygen and moisture vapor transmission protection • Can be made symmetrical or asymmetrical to meet customized needs of broad variety of applications • Barrier protection and superior organoleptic properties PolyOne Corporation Page 35 Aerospace Applications • Leading provider of specialty materials for the aerospace industry • Typical applications  Mil-spec aircraft windows, canopies, windscreens, instrument panels, wingtip lenses  Interior – gallery furnishings, tray tables, arm rests, trim strips, joint/edge coverings • Benefits:  High impact strength  Resistant to UV rays  Flame and smoke compliance  Easy to clean with aggressive cleaners; anti-microbial grades available  Range of sizes, thicknesses, colors, etc.

Design conceptualization and rendering services can help bring your vision to life and embody your brand • Recommendations on overmolding and texture will optimize your production and performance Avient Corporation 7 Dampener 11 Stopper 12 9 Plunger 10 Avient Corporation 8 Internal Mechanical Performance Performance and reliability are vital when designing for more effective treatments and better patient outcomes. Requirements: Soft dampening to protect the vial and other components Versaflex™ VDT TPEs 12. Avient Corporation 12

The company noted that second quarter 2024 GAAP EPS includes $0.24 of special items (see Attachment 3) and $0.16 of intangible amortization expense (see Attachment 1). 2) Tax adjustments include the net tax impact from non-recurring income tax items, adjustments to uncertain tax position reserves and the establishment, reversal or changes to valuation allowances. 10 Attachment 4 Avient Corporation Condensed Consolidated Balance Sheets (In millions) (Unaudited) June 30, 2024 December 31, 2023 ASSETS Current assets: Cash and cash equivalents $ 489.4 $ 545.8 Accounts receivable, net 486.6 399.9 Inventories, net 365.9 347.0 Other current assets 117.2 114.9 Total current assets 1,459.1 1,407.6 Property, net 1,019.9 1,028.9 Goodwill 1,685.1 1,719.3 Intangible assets, net 1,515.7 1,590.8 Other non-current assets 228.0 221.9 Total assets $ 5,907.8 $ 5,968.5 LIABILITIES AND SHAREHOLDERS' EQUITY Current liabilities: Short-term and current portion of long-term debt $ 657.7 $ 9.5 Accounts payable 435.2 432.3 Accrued expenses and other current liabilities 405.3 331.8 Total current liabilities 1,498.2 773.6 Non-current liabilities: Long-term debt 1,420.8 2,070.5 Pension and other post-retirement benefits 63.3 67.2 Deferred income taxes 276.3 281.6 Other non-current liabilities 315.0 437.6 Total non-current liabilities 2,075.4 2,856.9 SHAREHOLDERS' EQUITY Avient shareholders’ equity 2,317.5 2,319.2 Noncontrolling interest 16.7 18.8 Total equity 2,334.2 2,338.0 Total liabilities and equity $ 5,907.8 $ 5,968.5 11 Attachment 5 Avient Corporation Condensed Consolidated Statements of Cash Flows (Unaudited) (In millions) Six Months Ended June 30, 2024 2023 Operating Activities Net income $ 83.5 $ 42.7 Adjustments to reconcile net income to net cash provided (used) by operating activities: Depreciation and amortization 88.4 96.2 Accelerated depreciation 0.8 1.9 Share-based compensation expense 9.0 6.5 Changes in assets and liabilities: Increase in accounts receivable (97.0) (66.6) (Increase) decrease in inventories (27.3) 14.0 Increase (decrease) in accounts payable 11.9 (26.2) Taxes paid on gain on sale of business — (103.0) Accrued expenses and other assets and liabilities, net (6.2) 9.8 Net cash provided (used) by operating activities 63.1 (24.7) Investing activities Capital expenditures (55.8) (45.9) Net proceeds from divestiture — 7.3 Proceeds from plant closures 3.4 — Other investing activities (2.1) — Net cash used by investing activities (54.5) (38.6) Financing activities Cash dividends paid (47.0) (45.0) Repayment of long-term debt (4.5) (1.0) Other financing activities (3.3) (2.3) Net cash used by financing activities (54.8) (48.3) Effect of exchange rate changes on cash (10.2) (0.8) Decrease in cash and cash equivalents (56.4) (112.4) Cash and cash equivalents at beginning of year 545.8 641.1 Cash and cash equivalents at end of period $ 489.4 $ 528.7 12 Attachment 6 Avient Corporation Business Segment Operations (Unaudited) (In millions) Operating income and earnings before interest, taxes, depreciation and amortization (EBITDA) at the segment level does not include: special items as defined in Attachment 3; corporate general and administration costs that are not allocated to segments; intersegment sales and profit eliminations; share-based compensation costs; and certain other items that are not included in the measure of segment profit and loss that is reported to and reviewed by the chief operating decision maker.

Continue fostering our Great Place to Work® culture Strategic Objectives Long Term Growth Rates Growth Drivers $340 $455 $790 $1,135 $51 $84 $212 $645 $108 $113 $231 $230 $265 $358 $726 $725 8-12% 8-10% 8-10% 5% Sustainable Solutions Composites Healthcare Asia/Emerging Regions Profitable Growth Great Place to Work 5.4% 10.9% 16.0% 2006 2014 2023 EBITDA Margins $0.14 $1.93 $2.36 2006 2014 2023 TOP-TIER SUSTAINABILITY PERFORMANCE AND RECOGNITION Industry Sustainability Standards ESG Ratings Performance 1 4 87th 94th percentile 5 Avient CDP Score: A- FE BRUARY 14 , 2024 W E BCAS T P RE S E N TAT I O N DR. ASHISH KHANDPUR PRESIDENT & CEO 7 8 PORTFOLIO TRANSFORMATION 8 46% 66% 87% 100% 0% 20% 40% 60% 80% 100% 2005 2010 2015 2020 2023 % o f A dj us te d EB IT D A Commodity JVs Distribution Performance Products & Solutions Specialty Businesses Adjusted EBITDA from Specialty Applications SUSTAINABILITY AS A GROWTH DRIVER 9 LONG-TERM REVENUE GROWTH DRIVERS Sustainable Solutions Composites, Healthcare, Asia / LATAM Overlap Other 60%+ Key Growth Drivers Total Company Revenue Growth Drivers Long-Term Growth Rate Sustainable Solutions 8–12% Composites 8–10% Healthcare 8–10% Asia / LATAM 5% Other 0–2% Avient 6% END MARKET OBSERVATIONS (% OF COMPANY SALES) ENERGY DEFENSE TELECOMMUNICATIONS HEALTHCARE 10 TRANSPORTATION INDUSTRIAL BUILDING & CONSTRUCTION 9% CONSUMER PACKAGING 23% 11 REGIONAL OBSERVATIONS (% OF COMPANY SALES) 11 Q 4 2023 RE S U LT S Q4 2023 PERFORMANCE VS. Three Months Ended Year Ended 2023 2022 2023 2022 Sales: Color, Additives and Inks $ 459.4 $ 490.8 $ 2,007.4 $ 2,355.0 Specialty Engineered Materials 259.8 300.8 1,138.2 1,044.4 Corporate (0.2) (1.2) (2.8) (2.5) Sales $ 719.0 $ 790.4 $ 3,142.8 $ 3,396.9 Operating income: Color, Additives and Inks $ 61.8 $ 44.3 $ 259.9 $ 301.0 Specialty Engineered Materials 29.4 35.2 142.5 140.1 Corporate (48.1) (79.1) (205.6) (197.8) Operating income $ 43.1 $ 0.4 $ 196.8 $ 243.3 Other expense, net: $ 4.3 $ (28.4) $ 5.8 $ (59.7) Depreciation & amortization: Color, Additives and Inks $ 22.2 $ 25.2 $ 98.3 $ 101.3 Specialty Engineered Materials 19.8 20.3 81.5 48.7 Corporate 2.2 3.1 9.0 12.5 Depreciation & amortization $ 44.2 $ 48.6 $ 188.8 $ 162.5 Earnings before interest, taxes, depreciation and amortization (EBITDA): Color, Additives and Inks $ 84.0 $ 69.5 $ 358.2 $ 402.3 Specialty Engineered Materials 49.2 55.5 224.0 188.8 Corporate (45.9) (76.0) (196.6) (185.3) Other expense, net $ 4.3 $ (28.4) $ 5.8 $ (59.7) EBITDA $ 91.6 $ 20.6 $ 391.4 $ 346.1 Special items in EBITDA 22.3 86.8 110.4 162.5 EBITDA - excluding special items $ 113.9 $ 107.4 $ 501.8 $ 508.6 APM pro forma adjustments - 8 months 2022* — — — 83.1 Pro forma EBITDA $ 113.9 $ 107.4 $ 501.8 $ 591.7 * Pro forma adjustment for January - August 2022 APM results (period before Avient ownership). 3 AVNT February IR Presentation.pdf Avient corporation�investor presentation DISCLAIMER Slide Number 3 Creating a world-class�sustainable organization Top-tier sustainability performance�and recognition Slide Number 6 Slide Number 7 Portfolio transformation Slide Number 9 END MARKET observations�(% of company sales) Regional observations�(% of company sales) Slide Number 12 Slide Number 13 Slide Number 14 Slide Number 15 Slide Number 16 Slide Number 17 Slide Number 18 Slide Number 19 Slide Number 20 Slide Number 21 Slide Number 22 2023 segment, end market and Geography Color, Additives & Inks Specialty Engineered Materials Slide Number 26 AVNT Q4 2023 Earnings Presentation.pdf AVNT Q4 2023 Earnings Presentation_For Website_with Non-GAAP.pdf IR Deck - AVNT-2023.12.31 (2.12.24 9PM Milestone February 12 0905 pm).pdf Attachment

Nutritional components in dairy products are photosensitive, making them susceptible to light degradation • Light protection in dairy packaging helps maintain product integrity and extend shelf life A LIGHT BLOCKING SOLUTION THAT PROVIDES: • Light blocking and whiteness in PET dairy packaging • Protection from 2 weeks up to 12 months shelf life • Compatibility with monolayer and multilayer PET preforms • Full compatibility with rPET • Food contact approved (region dependent) • Low TiO₂ levels to increase recyclability, aligning with the emergence of white recycle streams PASTEURIZED MILK Typical shelf life 5–10 days WHITE COLOR LACTRA ESL LACTRA SX or LACTRA 4 EXTENDED SHELF LIFE MILK 2 weeks–3 months UHT MILK & PRODUCTS 4–12 months Lightweighting/CO2 reduction Reduced LDR – material & cost savings Improved processing performance BENEFITS OF COLORMATRIX™ LACTRA™ Improved bottle Compatibility with rPET Helps to Protect Performance Energy efficiency Whiteness 85–92 L* 30% less life cycle emissions Increased machinery life cycle due to reduced wear & tear 80–100% light blocking © 2024, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012

PolyOne Corporation Investor Day 2012 PolyOne Investor Presentation Deutsche Bank 2013 Global Industrials and Basic Materials Conference June 12, 2013 • In this presentation, statements that are not reported financial results or other historical information are “forward-looking statements” within the meaning of the Private Securities Litigation Reform Act of 1995. Use of Non GAAP Measures Page 3 -150.00% -100.00% -50.00% 0.00% 50.00% 100.00% 150.00% 200.00% 250.00% 300.00% 350.00% PolyOne S&P 500 Strategy and Execution Drive Results Page 4 • Since 2006, PolyOne stock has expanded approximately 300% vs. a 30% increase in the S&P 500 All time closing high of $26.63 May 28, 2013 The World’s Premier Provider of Specialized Polymer Materials, Services & Solutions Four Pillar Strategy Page 5 2013 Portfolio Transformation Highlights • Substantial organic mix improvement drives 29% increase in first quarter EPS – 14th consecutive quarter of double-digit EPS growth • Completed acquisition of Spartech • Announced the creation of a new Specialty segment – Designed Structures and Solutions • Completed the sale of our non-core resin assets • Realigned our Specialty Coatings business into our GCAI segment Page 6 0.12 0.27 0.21 0.13 0.68 0.82 1.00 2.50 $0.00 $0.25 $0.50 $0.75 $1.00 $1.25 $1.50 $1.75 $2.00 $2.25 $2.50 2006 2007 2008 2009 2010* 2011* 2012* 2015 Target Ad ju st ed E ar ni ng s P er S ha re Appliance 6% Building & Construction 13% Wire & Cable Electrical & Electronics 4% Consumer Packaging 18% Industrial 10% Misc. 5% HealthCare Transportation 16% Textiles 1% PP&S 15% Specialty Distribution 25% United States 70% Europe 14% Canada 8% Asia 5% Latin America 3% 2012 Revenues: $4.0 Billion* End Markets* 2012 Revenues: $4.0 Billion* EPS Page 7 * Pro Forma includes FY2012 results for Spartech (11/03/12 YE) and Glasforms & excludes resin assets PolyOne At A Glance * Restated to exclude discontinued operations Old PolyOne Transformation *Operating Income excludes corporate charges and special items **Pro Forma results include Spartech and Glasforms acquisitions, Specialty Coatings reclass and excludes resin assets 2% 34% 43% 45% 60% 65 – 75% 0% 20% 40% 60% 80% 100% 2005 2008 2010 2012 2012PF** 2015 % o f O pe ra tin g In co m e* JV's PP&S Distribution Specialty Specialty OI $5M $46M $87M $114M $150M Target Mix Shift Highlights Specialty Transformation 2015 Target Page 8 2007 Q1 2013 2015 Target 1) Operating Income % Specialty: Global Color, Additives & Inks 4.6% 11.7% 12 – 16% Global Specialty Engineered Materials 1.3% 10.1% 12 – 16% Designed Structures & Solutions -- 4.6% 8 – 10% Performance Products & Solutions 6.1% 8.1% 9 – 12% Distribution 3.0% 6.0% 6 – 7.5% 2) Specialty Platform % of Operating Income 20% 60% 65 – 75% 3) ROIC* (after-tax) 7% 9.2% 15% 4) Adjusted EPS Growth N/A 29% Double Digit Expansion Proof of Performance & 2015 Goals *ROIC is defined as TTM adjusted OI divided by the sum of average debt and equity over a 5 quarter period Page 9 *Percentage of Specialty Platform revenue from products introduced in last five years 19.5% 50.0% 2006 Q1 2013 $20.3 $41.9 2006 2012 14.3% 27.8% 2006 Q1 2013 Research & Development Spending Specialty Platform Vitality Index Progression* Innovation Drives Earnings Growth ($ millions) Specialty Platform Gross Margin % Page 10 Positioned for Strong Growth 2015 Target Rev: $5B Adj. EPS: $1.00 First Quarter Financial Highlights • 14th consecutive quarter of double digit adjusted earnings per share growth • 29 percent increase in adjusted EPS  34 percent increase in Specialty operating income  Growth from all regions  Virtually all organic growth • Strengthened our financial position Page 12 • Total Debt at 3/31/13 Less: Cash Net Debt • Available Liquidity Cash ABL Availability Total Liquidity • Net Debt / EBITDA = 2.7x* $169 285 $454 $1,056 169 $887 $50 $360 $600 $0 $100 $200 $300 $400 $500 $600 $700 $800 2015 2020 2023 Debt Maturities As of March 31, 2013 ($ millions) Page 13 Coupon Rates: 7.500% 7.375% 5.250% *Pro Forma TTM with no synergies related to Spartech acquisition & excludes resin assets Debt Maturities & Liquidity Summary – 3/31/13 Cash Balance = $169M Net Debt / EBITDA* = 2.7x • Repurchased 840k shares in Q1 2013 • 19.1 million shares are available for repurchase under the current authorization Share Repurchase • Introduced a quarterly dividend in Q1 2011 and increased in Q1 2012 (25%) and Q1 2013 (20%) • Objective of maintaining and growing Dividends • Expanding our sales, marketing, and technical capabilities is top priority • Investing in operational and LSS initiatives (including synergy capture) • CAPEX Organic Growth • Targets that expand our: • Specialty offering • End market presence • Geographic footprint • Synergy opportunities • Adjacent material solutions Acquisitions *TTM with no synergies related to the Spartech acquisition Use of Cash Page 14 Why Invest In PolyOne?

Note que essa troca de informações ocorre mesmo que você não interaja com o plug-in. Note que, se desativar ou recusar cookies, algumas partes do site podem ficar inacessíveis ou não funcionar corretamente. Note que, se desativar ou recusar cookies, algumas partes do site podem ficar inacessíveis ou não funcionar corretamente.