% Specific Color Heat BROWN 83MB01 (c) Iron Oxide, Tan HR 60 1.78 PBr-11 1 I/O SBR 83MB02 (c) Iron Oxide, Light 68 2.1 PBr-6 2 C I/O SBR 83MB03 (c) Iron Oxide, Dark 60 1.83 PBr-6 2 C I/O SBR 83EP02 Iron Oxide, Light 69 1.98 PBr-6 2 C I/O EPDM 83EP03 Iron Oxide, Dark 69 1.98 PBr-6 2 C I/O EPDM BLACK 90MB01 (c) Furnace N-330 31 1.2 PBk-7 1 I/O SBR 90MB05 (c) Iron Oxide 60 1.8 PBk-11 2 C I/O SBR 90EP01 Furnace Black 33 1.05 PBk-7 1 I/O EPDM 90EP05 Iron Oxide 55 1.56 PBk-11 2 C I/O EPDM ALUMINUM 61MB01 Aluminum 70 1.5 PM-1 1 I/O SBR 61EP01 Aluminum 60 1.31 PM-1 1 I/O EPDM RS = Red Shade YS = Yellow Shade VYS = Very Yellow Shade BS = Blue Shade VBS = Very Blue Shade GS = Green Shade NC = Non-Crystallizing HR = Heat-Resistant (a) = Potential Migration at Low Use Levels (b) = Poor Alkali Resistance - Not Recommended for Open Steam Cure (c) = Six Month Shelf Life LIGHTFASTNESS I = Indoor Only I/O = Indoor or Outdoor Mass = Outdoor Masstone Application Only C = Some Caution Advised HEAT STABILITY 1 = Above 400°F 2 = 350°F–400°F 3 = Below 350°F C = Some Caution Advised 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

These Terms and Conditions (“Terms and Conditions”) shall apply to any and all sales of products (“Products”) of PolyOne Corporation and its affiliates ("Seller") to third parties (“Buyer”). 1. Estes Termos e Condições (“Termos e Condições”) aplicam-se a todas e quaisquer vendas de produtos (“Produtos) da PolyOne Corporation e suas afiliadas (“Vendedor”) a terceiros (“Comprador”). 1.2.

FASTENER SELECTION Copyright © 2020, Avient Corporation.

FASTENER TYPE BENEFITS CONSIDERATIONS FOAM HONEY COMB Through- bolting Best mechanical locking system Need back side access to panel ✓ ✓ Wide Grip (Bulb-Style) Rivet Highest pullout strengths Requires pilot hole ✓ Cup Washer Spreads compressive load Requires relief hole; for substructure and hard point attachment ✓ ✓ Wide Grip (Bulb-Style) Rivet Ease of use— no installation torque limitations For lower load attachments ✓ Sheet Metal or Wood Screw Readily available, low cost Penetrate both skins for improved pullout ✓ Shoulder Washer Limits compressive load Requires relief hole; for substructure and hard point attachment ✓ ✓ FASTENER SELECTION Copyright © 2023, Avient Corporation.

ESCR Design Guide 6 FIGURE 17 - Non-structural hole design guidelines 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

reSound™ REC VX2800-0003 C 65 Gray reSound™ REC OF 7310-80 reSound™ REC OF 7310-90 reSound™ REC GP 7820-340 reSound™ REC GP 7820-360 reSound™ REC GP 7820-380 Recycled Content PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend Recycled Content, % 25% 35% 45% 60% 60% 60% Recycled Source Food Food Food Transportation, Industrial Transportation, Industrial Transportation, Industrial Hardness, Shore A 65 80 90 36 63 77 Color Gray Black/Natural (Gray) Black/Natural (Gray) Natural Natural Natural Specific Gravity 0.88 0.9 0.91 0.95 0.98 1.0 Tensile Strength, PSI 831 1120 1590 1027 1012 1173 Elongation at Break, % 620 570 520 1600 1200 1000 Compression Set @ Room Temperature 26 32 37 24 30 39 OM Substrate PP PP PP PP PP PP Processing IM or OM IM IM IM IM IM Agency Rating Application Specific FDA – – – – – Automotive Testing* – VOC & FOG (VDA 278), Odor (VDA 270) VOC & FOG (VDA 278), Odor (VDA 270) – – – reSound™ REC VX7900-5001 C I 30A Natural VX7900-5001 C I 50A Natural reSound™ REC VX7900-5001 C I 70A reSound™ REC AF 7210-140 B AF 7210-150 B reSound™ REC AF 7210-160 B AF 7210-170 B AF 7210-180 B AF 7210-190 B Recycled Content PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend Recycled Content, % 81% 81% 83% 59% 57% 54% 57% 56% 51% PIR Recycled Source Proprietary Blend Proprietary Blend Proprietary Blend Transportation Transportation Transportation Transportation Transportation Transportation PCR Recycled Source Transportation/ Industrial Transportation Transportation Transportation Transportation Transportation Transportation Hardness, Shore A 30 50 70 43 51 61 70 81 90 Color Natural Natural Natural Black Black Black Black Black Black Specific Gravity 1.14 1.16 1.16 0.97 0.98 0.98 0.98 0.99 0.99 Tensile Strength, MPa 2.39 3.23 3.35 4 5 5 8 10 13 Elongation at Break, % 796 654 515 1013 993 981 935 876 829 Compression Set @ Room Temperature 16 24 37 41 44 44 48 54 55 OM Substrate PP PP PP PP PP PP PP PP PP Processing IM or OM IM or OM IM or OM IM IM IM IM IM IM EUROPE GRADES reSound™ REC VX2800-5032 C 47A reSound™ REC VX2800-5033 C 54A reSound™ REC GP 7820-140 GP 7820-160 reSound™ REC GP 7820-180 Recycled Content PCR PCR PCR PCR PCR Recycled Content, % 61% 61% 60% 60% 60% PCR Recycled Source Transportation Transportation Transportation/ Hardness, Shore A 47 54 38 57 77 Color Natural Natural Natural Natural Natural Specific Gravity 0.96 0.96 0.94 0.97 1.0 Tensile Strength, MPa 1.80 2.00 7.19 6.65 7 Elongation at Break, % 766 682 1590 1380 1010 Compression Set @ Room Temperature 28 29 28 32 38 OM Substrate PP PP PP PP PP Processing IM or OM IM or OM IM IM IM EUROPE GRADES ASIA GRADES - PIR reSound™ REC VX3120-801 reSound™ REC VX3120-802 reSound™ REC VX3120-803 Recycled Content PIR PIR PIR Recycled Content, % 20% 40% 60% Recycled Source Textile Textile Textile Hardness, Shore A 67 68 68 Color Natural Natural Natural Specific Gravity 1.11 1.10 1.11 Tensile Strength, PSI 1450 1229 1151 Elongation at Break, % 752 709 653 OM Substrate PC, ABS, PC, ABS, PC, ABS, Processing IM or OM IM or OM IM or OM reSound™ REC DY 7810-801 C 30A Natural reSound™ REC DY 7810-801 C 40A Natural reSound™ REC DY 7810-801 C 50A Natural reSound™ REC DY 7810-801 C 60A Natural reSound™ REC DY 7810-801 C 70A Natural reSound™ REC DY 7810-801 C 80A Natural reSound™ REC DY 7810-801 C 90A Natural reSound™ REC DY 7820-801 C 30A Natural reSound™ REC DY 7820-801 C 40A Natural reSound™ REC DY 7820-801 C 50A reSound™ REC DY 7820-801 C 60A Natural reSound™ REC DY 7820-801 C 70A Natural reSound™ REC DY 7820-801 C 80A Natural reSound™ REC DY 7820-801 C 90A Natural reSound™ REC 3630-801C 40N reSound™ REC 3630-801C 50N reSound™ REC 3630-801C 60N reSound™ REC 7850-90N FR GP 7820-240 GP 7820-260 GP 7820-280 Recycled Content PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR Recycled Content, % 9% 12% 15% 21% 23% 30% 39% 60% 60% 60% 60% 60% 60% 60% 45% 45% 45% 32% 60% 60% 60% Recycled Source Food Food Food Food Food Food Food Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Packaging, Food Hardness, Shore A 30 40 50 60 70 80 90 30 40 50 60 70 80 90 40 49 58 85 39 57 80 Color Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Specific Gravity 0.88 0.89 0.89 0.88 0.88 0.89 0.89 0.95 0.94 0.97 0.97 0.99 1.01 1.02 0.90 0.90 0.90 1.04 0.95 0.98 1.0 Tensile Strength, PSI 678 889 939 964 1057 1328 1619 663 804 830 859 844 1007 1279 830 965 985 1250 938 1089 1479 Elongation at Break, % >1000 983 893 750 726 699 599 1028 948 880 807 681 642 640 700 700 650 310 1600 1360 1090 OM Substrate PP PP PP PP PP PP PP PP PP PP PP PP PP PP PC, ABS, PC/ABS PC, ABS, PC/ABS PC, ABS, PC/ABS – PP 30 39 Processing IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM EM IM IM IM ASIA GRADES - PCR Copyright © 2024, Avient Corporation.

Ihrem Vorgesetzten oder einem anderen Avient- Manager • dem Corporate Ethics Officer unter der E-Mail- Adresse ethics.officer@avient.com • dem General Counsel unter der E-Mail-Adresse legal.officer@avient.com • einem beliebigen Mitarbeiter der Rechtsabteilung • der Ethik-Hotline von Avient Ethik-Hotline von Avient Die Ethik-Hotline ist weltweit in über 20 Sprachen täglich rund um die Uhr telefonisch und über eine Website zu erreichen. Ein unabhängiges Unternehmen empfängt alle über die Website und telefonisch eingehenden Meldungen an die Ethik-Hotline und leitet die entsprechenden Informationen an den Corporate Ethics Officer weiter.

ONCOLOR™ UL 94 COLORANTS HOW TO USE THE TABLES UL HB GENERIC RESIN TYPE FLAME MINIMUM THICKNESS MAXIMUM LET-DOWN Acetal Copolymer (POM) HB 1.50 1:20 Acrylonitrile Butadiene Styrene (ABS) HB 1.50 1:10 Ethylene Propylene Thermoplastic Rubber (EPTR) HB 1.50 1:20 High Impact Polystyrene (HIPS) HB 1.50 1:10 Liquid Crystal Polymer (LCP) HB 0.83 1:10 Polyamide (PA) HB 3.20 1:33 Polyamide (PA66 and PA 4/6) HB 0.81 1:20 Polyamide 6 (PA6) HB 0.75 1:25 Polyamide 66 (PA66) HB 0.40 1:40 Polybutylene Terephthalate (PBT) HB 0.81 1:20 Polybutylene Terephthalate/Polycarbonate (PBT/PC) HB 1.50 1:10 Polycarbonate (PC) HB 1.50 1:15 Polycarbonate/Acrylonitrile Butadiene Styrene (PC/ABS) HB 1.50 1:20 Polycarbonate/Polyethylene Terephthalate (PC/PET) HB 1.50 1:20 Polyethylene (PE) HB 1.50 1:50 Polyethylene Terephthalate (PET) HB 0.80 1:16.7 Polyketone HB 1.50 1:20 Polymethyl Methacrylate (PMMA) HB 3.00 1:25 Polypropylene (PP) HB 1.50 1:15 Polystyrene (PS) HB 0.83 1:15 Polyurethane (PUR) HB 1.50 1:25 Polyvinylchloride (PVC) HB 1.50 1:20 Styrene Acrylonitrile (SAN) HB 1.50 1:20 Thermoplastic Elastomer (TPE) HB 0.75 1:25 ASCEND GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 66 21X1(a)(f2), 21SPC1(a)(f2), 21SPF1(a)(f2), 21SPG1(a)(f2), 21SPM1(a)(f2), 20NSP1(a)(f2) 0.75 V-2 1:40 22HSP(e) 0.75 V-2 1:40 64C-R 3.0 V-2 1:50 ECO366(e) 0.4 V-0 1:40 ECO366H(e) 0.2 V-0 1:25 FR350J 0.4 V-0 1:25 20NSP(a)(f2), 21SPF(a)(f2), 21SPM(a)(f2), 21SPC(a)(f2) 0.4 V-2 1:40 20NSP(a)(h)(f2), 21SPF(a)(h)(f2), 21SPM(a)(h)(f2), 21SPC(a)(h) (f2) 1.5 V-2 1:20 Polyamide 66/6 (PA66/6) ECO315(e), ECO315J(e) 0.4 V-0 1:40 M344 3.0 V-0 1:25 909 0.75 V-0 1:25 BASF GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 6 8202(t1), 8202 Blend (t1) 0.71 V-2 1:25 8202C(t1), 8202C BLEND (t1) 1.50 V-2 1:25 8202CHS(t1) (t3), 8202C HS Blend 1.50 V-2 1:25 8202HS(t1) 1.50 V-2 1:25 B3S 0.80 V-2 1:25 B3S Q661 1.50 V-2 1:25 B3S R03 1.50 V-2 1:25 8232G HSFR(t9), B3U10G5 (t9) 1.50 V-0 1:25 Polyamide 6/66 (PA6/66) C3U (m) 0.40 V-0 1:25 KR4205(m), C3U (m), C3U (t)(m) 0.40 V-0 1:25 KR4205, C3U 0.40 V-0 1:25 Polyamide 66 1000(b), 1310-(b), Ultramid A3K Q603(+) 1.50 V-2 1:10 A3K (o) Q790(g)(f2) 0.41 V-2 1:20 A3K(f2), A3K Q601(f2) 0.41 V-2 1:20 A3SK 0.41 V-2 1:25 A5 3.00 V-2 1:33 A3W(f1), A3W FC (f1) 0.75 V-2 1:10 A3K R01 (t)(g)(f2) 0.40 V-2 1:20 Polybutylene Terephthalate B4406 G2 (o) Q798 1.50 V-0 1:20 B4406 G2(a), B4406 G2 (o) Q717(a) 1.50 V-0 1:20 B4406 G3 (o) Q798 1.50 V-0 1:20 B4406 G3(a), B4406 G3 (o) Q717(a) 1.50 V-0 1:20 B4406 G4 (o) Q798 1.50 V-0 1:20 B4406 G4(a2), B4406 G4 (o) Q717(a2) 1.50 V-0 1:20 B4406 G6 (o) Q798 3.00 V-0 1:12.5 B4406 G6(%) 1.50 V-0 1:20 B4406 G6(a1), B4406 G6 (o) Q717(a1), B4406 G6 (o) Q717 High Speed(a1) 1.50 V-0 1:20 B4406(a), B4406 (o) Q717(a) 1.50 V-0 1:20 B4406@ 1.50 V-0 1:20 B4450 G5, B4450 G5 (t) 0.40 V-2 1:50 Polyurethane (PUR) 11 85 A(a) FHF 000 (f2) 0.75 V-0 1:33 CELANESE GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Liquid Crystal Polymer (LCP) A130(+), MT1310 1.50 V-0 1:40 Polyamide (PA) 132F(+)(f1), 135F(+)(f1) 0.75 V-2 1:20 HTNFR42G30NH 0.40 V-0 1:25 Polyamide 6/12 (PA6/12) 151, 151L 1.50 V-2 1:25 Polyamide 66 A3 GF 25 V0XI 0.40 V-0 1:25 101(r9)(f1), 101F(r9)(f1), 101L(r9)(f1) 0.75 V-2 1:20 103FHS(+), 103HSL(+) 0.75 V-2 1:20 FR50(+)(f1) 0.35 V-0 1:20 FR7025V0F(+) 0.50 V-0 1:33 Polyamide 66/6 (PA66/6) FR72G25V0 0.80 V-0 1:25 Polyamide 66/6T (PA66/6T) FR95G25V0NH 0.40 V-0 1:25 HTNFR52G30BL(r3) 0.75 V-0 1:33 HTNFR52G30L(+), HTNFR52G30(+) 0.75 V-0 1:33 HTNFR52G30NH(r6) 0.40 V-0 1:25 0.75 V-0 1:10 HTNFR52G35BL 0.75 V-0 1:25 HTNFR52G35(+), HTNFR52G35 0.75 V-0 1:33 Polyamide 6T/ MPMDT HTNFR51G35L(+) 0.81 V-0 1:33 Polybutylene Terephthalate 2016(b) 1.50 V-0 1:20 3116(b) 1.50 V-0 1:20 3216(b) 1.50 V-0 1:20 3316(b) 1.50 V-0 1:20 3316HF 1.50 V-0 1:20 LW9030FR 1.50 V-0 1:25 T841FR (r4) 1.50 V-0 1:25 Polyethylene Terephthalate (PET) FR530(l)(+)(f1), FR530L(l)(+)(f1) 0.75 V-0 1:25 Thermoplastic Elastomer (TPE) HTR8068 1.60 V-0 1:25 DOMO GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide (PA) J 60X1 V30 0.40 V-0 1:25 Polyamide 6 PSB 286 0.80 V-2 1:25 3.00 V-2 1:25 S 60X1 V30 0.75 V-0 1.25 Polyamide 66 A 205F(r4) 0.38 V-2 1:25 A 225F 0.75 V-2 1:25 A 50H1 (r3)(f2) 0.40 V-0 1:25 A 30G1 0.40 V-0 1:25 COVESTRO GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polycarbonate 2407 + (z)(f1) 0.75-2.60 V-2 1:10 2807 + MAS183 0.75 V-2 1:25 6455 + (z) 6485 + (z)(f1) 1.50 V-0 1:25 Acrylonitrile Butadiene Styrene FR110 + 1.50 V-0 1:33 FR3005 HF + (z), FR3005 HF + BBS314 1.50 V-0 1:12.5 FR3010 + (z) 1.50 V-0 1:25 FR3010 HF + 3.00 V-0 1:25 FR3030 + 3.00 V-0 1:25 ENVALIOR GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 46 (PA46) TE250F6(h1)(j) 0.50 V-0 1:25 Polyamide 6 F223-D(f1), F223-D /A(f1) 0.75 V-2 1:25 K222-KGV5(f1) 0.75 V-2 1:16.7 1.50 V-2 1:16.7 K-FKGS6/B(f1)(y) 0.80 V-0 1:25 Polyamide 66 (PA66) SG-KGS6/HV 0.75 V-0 1:25 Thermoplastic Elastomer (TPE) PL460-S 1.60 V-0 1:25 Polyamide 4T (PA4T) T11 (h) 0.40 V-0 1:20 EXXONMOBIL LANXESS GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Ethylene Propylene Thermoplastic Rubber (EPTR) 251-80W232(f7) 1.50 V-2 1:20 251-92W232 1.50 V-0 1:20 251-70W232 1.00 V-2 1:10 GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 6 B30S+(f1) 1.50 V-2 1:25 B31SK+ 1.50 V-2 1:25 Polybutylene Terephthalate B4235+ 1.50 V-0 1:10 TP364-302+, BF4232+(f1) 0.75 V-0 1:25 GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polybutylene Terephthalate 310(w) 1.50 V-0 1:20 310SE0(w) 1.50 V-0 1:20 310SE0(w),310SE0R(w) 1.50 V-0 1:20 420SE0(f1)(w)(GG)(rr1) 1.50 V-0 1:20 420SE0(f1)(w)(GG)(rr2) 1.50 V-0 1:20 457(w) 1.50 V-0 1:20 457(w), 451(w) 1.50 V-0 1:20 553(a)(f1)(w) 1.50 V-0 1:20 553(a)(f1)(w), 553E(a)(f1)(w), 553U(a)(f1)(w) 1.50 V-0 1:20 553(w)(f1), 553M(w)(f1) 1.50 V-0 1:20 DR48(w) 1.50 V-0 1:20 DR48,DR48M 1.50 V-0 1:20 V4760(a2) 0.40 V-0 1:20 EXVX1259, ENH4550 0.40 V-0 1:20 771 0.75 V-0 1:25 Polybutylene Terephthalate/ Polycarbonate (PBT/PC) 357(f1)(w)(IC), 357M(f1)(w)(IC), 357U(f1)(w)(IC) 1.50 V-0 1:20 357(f1)(w)(IC), 357U(f1)(w)(IC) 1.50 V-0 1:20 357X(f1) 1.50 V-0 1:20 V3900WX(GG)(f1)(IA), V3901WX(GG)(f1)(IA) 3.00 V-0 1:20 1.50 V-0 1:20 357(w)(f2)(IC), 357M(w)(f2)(IC), 357U(w)(f2)(IC) 1.50 V-0 1:20 GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polycarbonate 221(f2) 1.50 V-2 1:25 221R(f2) 1.50 V-2 1:25 500(f2), 500R(f2) 3.00 V-0 1:33 503(f1) 3.00 V-0 10:1 1.50 V-0 10:1 503(f1), 503R(f1) 3.00 V-0 10:1 1.50 V-0 10:1 943(ab) 1.50 V-0 1:20 943(f1) 1.50 V-0 1:20 943(f1), 923(f1) 1.50 V-0 1:20 950A, 920ASR, FXD911A(GG), 940ASR 1.50 V-2 1:25 CFR7630(f1)(gg*) 1.50 V-0 1:25 ML5139R(f2) 3.00 V-0 1:33 950A, FXD911A(GG), 940ASR 3.00 V-0 1:25 943 1.50 V-0 1:20 920A Acrylonitrile Butadiene Styrene C2950 1.50 V-0 6:100 C6200(GG) 2.00 V-0 1:20 Acrylonitrile Styrene Acrylate/ Polycarbonate (ASA/PC) HRA222 (GG) 0.80 V-2 1:20 SOLVAY (SYENSQO) GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyphenyl Sulfone (PPSU) R-5100 (r1)(##), R-5000 (r1)(##) 1.50 V-0 1:10 Polyphthalamide (PPA) AFA-4133 V0(+) (*) 0.75 V-0 1:25 BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN ALBIS Polypropylene (PP) PP 13 CV2 14 1.50 V-2 1:25 AVIENT Polyvinylchloride M3700(X), M3755(X) 1.50 V-0 1:25 M3900 1.50 V-0 1:25 CHI MEI Acrylonitrile Butadiene Styrene (ABS) PA-765(+) 1.50 V-0 1:10 Acrylonitrile Butadiene Styrene PC-510(+) 1.50 V-0 1:25 EMS-CHEMIE Polyamide 6 (PA6) Grilon A 26 V0 0.75 V-0 1:25 FORMOSA Polycarbonate (PC) #1700+(f2) 0.36-0.42 V-2 1:50 GEON Polyvinylchloride 85891(f1) 1.70 V-0 1:20 85891(f2) 1.70 V-0 1:20 M3700(X) 1.50 V-0 1:25 M3900 1:25 INEOS Polystyrene (PS) 855 HV 3.00 V-1 100:4 INVISTA Polyamide 66 FRU4800 XHL (r1) 0.40 V-0 1:25 U4820L (r1) 0.40 V-2 1:25 BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN KINGFA Polyamide 66 (PA66) PA66-R11G25 (##) 0.25 V-0 1:25 KURARAY Polyamide 9T (PA9T) GP2300S 0.40 V-0 1:25 LG CHEM Acrylonitrile Butadiene Styrene LUPOY GP-5106-F 3.00 V-0 1:20 LOTTE CHEMICAL Acrylonitrile Butadiene Styrene (ABS) VH-0800(+) 1.50 V-0 1:25 Polycarbonate (PC) HN-1064(+) 0.75 V-2 1:10 1.20 V-1 1:10 Polystyrene (PS) VH-1800+ 1.50 V-0 1:25 MITSUBISHI Polycarbonate (PC) S-2000+(f1) 1.50-1.80 V-2 1:10 POLYMER PRODUCTS Polystyrene (PS) ZYNTAR 351 2.00 V-0 1:20 1.50 V-0 1:20 ZYNTAR 7000 2.00 V-0 1:25 ZYNTAR 702 2.00 V-0 1:25 8020 2.00 V-0 1:20 8120 2.00 V-0 1:20 8130 1.50 V-0 1:20 POLYMER RESOURCES Polycarbonate PC-FR1A-D, PC- FR2A-D, PC-FR3A-D 3.00 V-0 1:33 1.50 V-2 1:33 SUMITOMO Liquid Crystal Polymer (LCP) E6007LHF(ra) 0.30 V-0 1:25 E6007LHF-MR(gt) 0.20 V-0 1:12.5 BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN TORAY Polyamide 6 (PA6) 1017 1.60 V-2 1:16.5 Polyamide 66 3004-V0(rr), CM3004-V0(rr) 0.40 V-0 1:25 TRINSEO Polycarbonate (PC) 891(w) 1.10 V-0 1:25 WELLMAN Polyamide 66/6 (PA66/6) 220-N, 21L-N, 22L-N 1.50 V-2 1:25 WESTLAKE Polyvinylchloride 6597(f1), HF-6597(f1) 1.50 V-0 1:25 SP-7107 (f1)(a) 3.00 V-0 1:25 5VA AND 5VB BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME RATING COLORS MAXIMUM LET-DOWN AVIENT Polyvinylchloride (PVC) M3900 1.50 5VB ALL 1:25 WHITE 1:10 CELANESE Polyamide 66/6T (PA66/6T) FR95G25V0NH 1.50 5VA ALL 1:25 Polybutylene Terephthalate LW9030FR 2.00 5VA BLACK 1:25 3.00 5VA ALL 1:25 SK642FR 1.50 5VA BLACK 1:25 COVESTRO Acrylonitrile Butadiene Styrene FR3010 + (z) 3.00 5VA ALL 1:25 GEON Polyvinylchloride (PVC) M3900 1.50 5VB ALL 1:25 WHITE 1:10 Polybutylene Terephthalate/ Polycarbonate (PBT/PC) V3900WX(GG)(f1)(IA), V3901WX(GG)(f1)(IA) 3.00 5VA ALL 1:20 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

RENOL™ UL94 COMPLIANT MASTERBATCHES HOW TO USE THE TABLES UL HB GENERIC RESIN TYPE FLAME MINIMUM THICKNESS MAXIMUM LET-DOWN Acetal Copolymer (POM) HB 1.50 1:20 Acrylonitrile Butadiene Styrene (ABS) HB 1.50 1:10 Ethylene Propylene Thermoplastic Rubber (EPTR) HB 1.50 1:20 High Impact Polystyrene (HIPS) HB 1.50 1:10 Liquid Crystal Polymer (LCP) HB 0.83 1:10 Polyamide (PA) HB 3.20 1:33 Polyamide (PA66 and PA 4/6) HB 0.81 1:20 Polyamide 6 (PA6) HB 0.75 1:25 Polyamide 66 (PA66) HB 0.40 1:40 Polybutylene Terephthalate (PBT) HB 0.81 1:20 Polybutylene Terephthalate/Polycarbonate (PBT/PC) HB 1.50 1:10 Polycarbonate (PC) HB 1.50 1:15 Polycarbonate/Acrylonitrile Butadiene Styrene (PC/ABS) HB 1.50 1:20 Polycarbonate/Polyethylene Terephthalate (PC/PET) HB 1.50 1:20 Polyethylene (PE) HB 1.50 1:50 Polyethylene Terephthalate (PET) HB 0.80 1:16.7 Polyketone HB 1.50 1:20 Polymethyl Methacrylate (PMMA) HB 3.00 1:25 Polypropylene (PP) HB 1.50 1:15 Polystyrene (PS) HB 0.83 1:15 Polyurethane (PUR) HB 1.50 1:25 Polyvinylchloride (PVC) HB 1.50 1:20 Styrene Acrylonitrile (SAN) HB 1.50 1:20 Thermoplastic Elastomer (TPE) HB 0.75 1:25 ASCEND GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 66 21X1(a)(f2), 21SPC1(a)(f2), 21SPF1(a)(f2), 21SPG1(a)(f2), 21SPM1(a)(f2), 20NSP1(a)(f2) 0.75 V-2 1:40 22HSP(e) 0.75 V-2 1:40 64C-R 3.0 V-2 1:50 ECO366(e) 0.4 V-0 1:40 ECO366H(e) 0.2 V-0 1:25 FR350J 0.4 V-0 1:25 20NSP(a)(f2), 21SPF(a)(f2), 21SPM(a)(f2), 21SPC(a)(f2) 0.4 V-2 1:40 20NSP(a)(h)(f2), 21SPF(a)(h)(f2), 21SPM(a)(h)(f2), 21SPC(a)(h) (f2) 1.5 V-2 1:20 Polyamide 66/6 (PA66/6) ECO315(e), ECO315J(e) 0.4 V-0 1:40 M344 3.0 V-0 1:25 909 0.75 V-0 1:25 BASF GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 6 8202(t1), 8202 Blend (t1) 0.71 V-2 1:25 8202C(t1), 8202C BLEND (t1) 1.50 V-2 1:25 8202CHS(t1) (t3), 8202C HS Blend 1.50 V-2 1:25 8202HS(t1) 1.50 V-2 1:25 B3S 0.80 V-2 1:25 B3S Q661 1.50 V-2 1:25 B3S R03 1.50 V-2 1:25 8232G HSFR(t9), B3U10G5 (t9) 1.50 V-0 1:25 Polyamide 6/66 (PA6/66) C3U (m) 0.40 V-0 1:25 KR4205(m), C3U (m), C3U (t)(m) 0.40 V-0 1:25 KR4205, C3U 0.40 V-0 1:25 Polyamide 66 1000(b), 1310-(b), Ultramid A3K Q603(+) 1.50 V-2 1:10 A3K (o) Q790(g)(f2) 0.41 V-2 1:20 A3K(f2), A3K Q601(f2) 0.41 V-2 1:20 A3SK 0.41 V-2 1:25 A5 3.00 V-2 1:33 A3W(f1), A3W FC (f1) 0.75 V-2 1:10 A3K R01 (t)(g)(f2) 0.40 V-2 1:20 Polybutylene Terephthalate B4406 G2 (o) Q798 1.50 V-0 1:20 B4406 G2(a), B4406 G2 (o) Q717(a) 1.50 V-0 1:20 B4406 G3 (o) Q798 1.50 V-0 1:20 B4406 G3(a), B4406 G3 (o) Q717(a) 1.50 V-0 1:20 B4406 G4 (o) Q798 1.50 V-0 1:20 B4406 G4(a2), B4406 G4 (o) Q717(a2) 1.50 V-0 1:20 B4406 G6 (o) Q798 3.00 V-0 1:12.5 B4406 G6(%) 1.50 V-0 1:20 B4406 G6(a1), B4406 G6 (o) Q717(a1), B4406 G6 (o) Q717 High Speed(a1) 1.50 V-0 1:20 B4406(a), B4406 (o) Q717(a) 1.50 V-0 1:20 B4406@ 1.50 V-0 1:20 B4450 G5, B4450 G5 (t) 0.40 V-2 1:50 Polyurethane (PUR) 11 85 A(a) FHF 000 (f2) 0.75 V-0 1:33 CELANESE GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Liquid Crystal Polymer (LCP) A130(+), MT1310 1.50 V-0 1:40 Polyamide 66 (PA66) A3 GF 25 V0XI, A G5 FR C4 0.40 V-0 1:25 Polybutylene Terephthalate 2012-2 1.50 V-0 1:20 2016(b) 1.50 V-0 1:20 3112-2 1.50 V-0 1:20 3116(b) 1.50 V-0 1:20 3216(b) 1.50 V-0 1:20 3310-2(f2) 1.50 V-0 1:20 3311-3(f2) 1.50 V-0 1:20 3316(b) 1.50 V-0 1:20 3316(b), 3316HF 1.50 V-0 1:20 COVESTRO GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polycarbonate 2407 + (z)(f1) 0.75-2.60 V-2 1:10 2807 + MAS183 0.75 V-2 1:25 6455 + (z) 6485 + (z)(f1) 1.50 V-0 1:25 Acrylonitrile Butadiene Styrene FR110 + 1.50 V-0 1:33 FR3005 HF + (z), FR3005 HF + BBS314 1.50 V-0 1:12.5 FR3010 + (z) 1.50 V-0 1:25 FR3010 HF + 3.00 V-0 1:25 FR3030 + 3.00 V-0 1:25 DSM GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 46 (PA46) TE250F6(h1)(j) 0.50 V-0 1:25 Polyamide 6 F223-D(f1), F223-D /A(f1) 0.75 V-2 1:25 K222-KGV5(f1) 0.75 V-2 1:16.7 1.50 V-2 1:16.7 K-FKGS6/B(f1)(y) 0.80 V-0 1:25 Polyamide 66 (PA66) SG-KGS6/HV 0.75 V-0 1:25 Thermoplastic Elastomer (TPE) PL460-S 1.60 V-0 1:25 Polyamide 4T (PA4T) T11 (h) 0.40 V-0 1:20 DOMO GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide (PA) J 60X1 V30 0.40 V-0 1:25 Polyamide 6 (PA6) PSB 286 0.80 V-2 1:25 3.00 V-2 1:25 Polyamide 66 A 205F(r4) 0.38 V-2 1:25 A 225F 0.75 V-2 1:25 A 50H1 (r3)(f2) 0.40 V-0 1:25 A 30G1 0.40 V-0 1:25 DUPONT GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide (PA) 132F(+)(f1), 135F(+)(f1) 0.75 V-2 1:20 HTNFR42G30NH 0.40 V-0 1:25 Polyamide 6/12 (PA6/12) 151, 151L 1.50 V-2 1:25 Polyamide 66 101(r9)(f1), 101F(r9)(f1), 101L(r9)(f1), E101(r9)(f1), E101L(r9)(f1) 0.75 V-2 1:20 103FHS(+), 103HSL(+), RN5077E(+), E103HSL(+) 0.75 V-2 1:20 A428 0.75 V-0 1:20 FE3757(+) 0.75 V-2 1:25 FR15(+) 0.75 V-0 1:20 FR50(+)(f1) 0.35 V-0 1:20 FR7025V0F(+) 0.50 V-0 1:33 Polyamide 66/6 (PA66/6) FR72G25V0 0.80 V-0 1:25 Polyamide 66/6T (PA66/6T) FR95G25V0NH 0.40 V-0 1:25 Polyamide 6T/66 (PA6T/66) HTNFR52G15AL 0.75 V-0 1:33 HTNFR52G30BL(r3) 0.75 V-0 1:33 HTNFR52G30L(+), FE15502(+), HTNFR52G30AL(+) 0.75 V-0 1:33 HTNFR52G30NH(r6) 0.40 V-0 1:25 0.75 V-0 1:10 HTNFR52G35BL 0.75 V-0 1:25 HTNFR52G35L(+), HTNFR52G35AL 0.75 V-0 1:33 Polyamide 6T/ MPMDT HTNFR51G35L(+) 0.81 V-0 1:33 Polybutylene Terephthalate LW9030FR 1.50 V-0 1:25 S650FR 1.50 V-0 1:25 SK642FR 1.50 V-0 1:25 SK652FR1 1.50 V-0 1:16.5 T841FR (r4) 1.50 V-0 1:25 Polyethylene Terephthalate (PET) FR530(l)(+)(f1), FR530L(l)(+)(f1) 0.75 V-0 1:25 Thermoplastic Elastomer (TPE) HTR8068 1.60 V-0 1:25 EXXONMOBIL GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Ethylene Propylene Thermoplastic Rubber (EPTR) 251-80W232(f7) 1.50 V-2 1:20 251-92W232 1.50 V-0 1:20 251-70W232 1.00 V-2 1:10 LANXESS GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyamide 6 B30S+(f1) 1.50 V-2 1:25 B31SK+ 1.50 V-2 1:25 Polybutylene Terephthalate B4235+ 1.50 V-0 1:10 TP364-302+, BF4232+(f1) 0.75 V-0 1:25 GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polybutylene Terephthalate 310(w) 1.50 V-0 1:20 310SE0(w) 1.50 V-0 1:20 310SE0(w),310SE0R(w) 1.50 V-0 1:20 420SE0(f1)(w)(GG)(rr1) 1.50 V-0 1:20 420SE0(f1)(w)(GG)(rr2) 1.50 V-0 1:20 457(w) 1.50 V-0 1:20 457(w), 451(w) 1.50 V-0 1:20 553(a)(f1)(w) 1.50 V-0 1:20 553(a)(f1)(w), 553E(a)(f1)(w), 553U(a)(f1)(w) 1.50 V-0 1:20 553(w)(f1), 553M(w)(f1) 1.50 V-0 1:20 DR48(w) 1.50 V-0 1:20 DR48,DR48M 1.50 V-0 1:20 V4760(a2) 0.40 V-0 1:20 EXVX1259, ENH4550 0.40 V-0 1:20 771 0.75 V-0 1:25 Polybutylene Terephthalate/ Polycarbonate (PBT/PC) 357(f1)(w)(IC), 357M(f1)(w)(IC), 357U(f1)(w)(IC) 1.50 V-0 1:20 357(f1)(w)(IC), 357U(f1)(w)(IC) 1.50 V-0 1:20 357X(f1) 1.50 V-0 1:20 V3900WX(GG)(f1)(IA), V3901WX(GG)(f1)(IA) 3.00 V-0 1:20 1.50 V-0 1:20 357(w)(f2)(IC), 357M(w)(f2)(IC), 357U(w)(f2)(IC) 1.50 V-0 1:20 GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polycarbonate 221(f2) 1.50 V-2 1:25 221R(f2) 1.50 V-2 1:25 500(f2), 500R(f2) 3.00 V-0 1:33 503(f1) 3.00 V-0 10:1 1.50 V-0 10:1 503(f1), 503R(f1) 3.00 V-0 10:1 1.50 V-0 10:1 943(ab) 1.50 V-0 1:20 943(f1) 1.50 V-0 1:20 943(f1), 923(f1) 1.50 V-0 1:20 950A, 920ASR, FXD911A(GG), 940ASR 1.50 V-2 1:25 CFR7630(f1)(gg*) 1.50 V-0 1:25 ML5139R(f2) 3.00 V-0 1:33 950A, FXD911A(GG), 940ASR 3.00 V-0 1:25 943 1.50 V-0 1:20 920A Acrylonitrile Butadiene Styrene C2950 1.50 V-0 6:100 C6200(GG) 2.00 V-0 1:20 Acrylonitrile Styrene Acrylate/ Polycarbonate (ASA/PC) HRA222 (GG) 0.80 V-2 1:20 SOLVAY GENERIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN Polyphenyl Sulfone (PPSU) R-5100 (r1)(##), R-5000 (r1)(##) 1.50 V-0 1:10 Polyphthalamide (PPA) AFA-4133 V0(+) (*) 0.75 V-0 1:25 BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN ALBIS Polypropylene (PP) PP 13 CV2 14 1.50 V-2 1:25 AVIENT Polyvinylchloride M3700(X), M3755(X) 1.50 V-0 1:25 M3900 1.50 V-0 1:25 CHI MEI Acrylonitrile Butadiene Styrene (ABS) PA-765(+) 1.50 V-0 1:10 Acrylonitrile Butadiene Styrene PC-510(+) 1.50 V-0 1:25 EMS-CHEMIE Polyamide 6 (PA6) Grilon A 26 V0 0.75 V-0 1:25 FORMOSA Polycarbonate (PC) #1700+(f2) 0.36-0.42 V-2 1:50 GEON Polyvinylchloride 85891(f1) 1.70 V-0 1:20 85891(f2) 1.70 V-0 1:20 M3700(X) 1.50 V-0 1:25 M3900 1:25 INEOS Polystyrene (PS) 855 HV 3.00 V-1 100:4 INVISTA Polyamide 66 FRU4800 XHL (r1) 0.40 V-0 1:25 U4820L (r1) 0.40 V-2 1:25 BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN KINGFA Polyamide 66 (PA66) PA66-R11G25 (##) 0.25 V-0 1:25 KURARAY Polyamide 9T (PA9T) GP2300S 0.40 V-0 1:25 LG CHEM Acrylonitrile Butadiene Styrene LUPOY GP-5106-F 3.00 V-0 1:20 LOTTE CHEMICAL Acrylonitrile Butadiene Styrene (ABS) VH-0800(+) 1.50 V-0 1:25 Polycarbonate (PC) HN-1064(+) 0.75 V-2 1:10 1.20 V-1 1:10 Polystyrene (PS) VH-1800+ 1.50 V-0 1:25 MITSUBISHI Polycarbonate (PC) S-2000+(f1) 1.50-1.80 V-2 1:10 POLYMER PRODUCTS Polystyrene (PS) ZYNTAR 351 2.00 V-0 1:20 1.50 V-0 1:20 ZYNTAR 7000 2.00 V-0 1:25 ZYNTAR 702 2.00 V-0 1:25 8020 2.00 V-0 1:20 8120 2.00 V-0 1:20 8130 1.50 V-0 1:20 POLYMER RESOURCES Polycarbonate PC-FR1A-D, PC- FR2A-D, PC-FR3A-D 3.00 V-0 1:33 1.50 V-2 1:33 SUMITOMO Liquid Crystal Polymer (LCP) E6007LHF(ra) 0.30 V-0 1:25 E6007LHF-MR(gt) 0.20 V-0 1:12.5 BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME MAXIMUM LET-DOWN TORAY Polyamide 6 (PA6) 1017 1.60 V-2 1:16.5 Polyamide 66 3004-V0(rr), CM3004-V0(rr) 0.40 V-0 1:25 TRINSEO Polycarbonate (PC) 891(w) 1.10 V-0 1:25 WELLMAN Polyamide 66/6 (PA66/6) 220-N, 21L-N, 22L-N 1.50 V-2 1:25 WESTLAKE Polyvinylchloride 6597(f1), HF-6597(f1) 1.50 V-0 1:25 SP-7107 (f1)(a) 3.00 V-0 1:25 5VA AND 5VB BASE RESIN GENERIC SPECIFIC MINIMUM THICKNESS FLAME RATING COLORS MAXIMUM LET-DOWN AVIENT Polyvinylchloride (PVC) M3900 1.50 5VB ALL 1:25 WHITE 1:10 COVESTRO Acrylonitrile Butadiene Styrene FR3010 + (z) 3.00 5VA ALL 1:25 DUPONT Polyamide 66/6T (PA66/6T) FR95G25V0NH 1.50 5VA ALL 1:25 Polybutylene Terephthalate LW9030FR 2.00 5VA BLACK 1:25 3.00 5VA ALL 1:25 SK642FR 1.50 5VA BLACK 1:25 GEON Polyvinylchloride (PVC) M3900 1.50 5VB ALL 1:25 WHITE 1:10 Polybutylene Terephthalate/ Polycarbonate (PBT/PC) V3900WX(GG)(f1)(IA), V3901WX(GG)(f1)(IA) 3.00 5VA ALL 1:20 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

ÁLTALÁNOS SZERZŐDÉSI FELTÉTELEK Ezek az Általános Szerződési Feltételek szabályozzák a termékek értékesítését egy másik félnek („Vevő”) az Avient Corporation és annak leányvállalatai („Eladó”) által. 1.