PRODUCT FR™ 0521-48 R1 FR™ 0587-21 R3 TYPE LSFOH PP ✔ Halogenated FR PP ✔ APPLICATION Crossweb ✔ ✔ Insulation ✔ GENERAL PROPERTIES Specific gravity g/cm3 1.50 1.46 LOI % 31 34 Tensile Strength MPa 13.8 15.9 Elongation % 320 320 Dielectric constant 1MHz 3.06 2.88 Shore D - 72 75.6 T°C max/T°F Max °C/°F 232/450 232/450 FIRE PERFORMANCE UL 444 ✔ ✔ Plenum yellow card ✔ ✔

Parameters NM5600-8002 RS NM5600-8004 RS Drying Temperature 100–120°C 100–130°C Drying Time 4–6 hours 4–6 hours Barrel Temperature °C °C Rear Zone 250–270 260–270 Central Zone 260–280 270–290 Front Zone 270–295 290–305 Nozzle 290–300 290–300 Mold Temperature 80–100 80–100 Screw Speed Moderate Moderate Back Pressure 3–10bar 3–10bar Cushion stroke 5–10% of plasticizing stroke 5–10% plasticizing of stroke Injection Speed Medium Medium Injection Pressure Medium–high Medium–high Holding Pressure 30–50% of injection pressure 20–40% of injection pressure Screw Type General purpose General purpose Screw L/D 20:1 20:1 Screw Compression Ratio 2.5:1 2.5:1 Non-return Check Valve Free flow check ring Free flow check ring Nozzle Type Reverse taper Reverse taper Barrel Capacity 30–80% of barrel should be used Processing Guide 2 Start Up & Shut Down Recommendations Purge Compound 1. 2–3 melt flow PP or purging compound.

Injection Molding Parameters Base Resin PPA PPS PA 6/6 PA 12 Barrel Temperatures °F (°C)* Rear Zone 550–580 (288–305) 550–580 (288–305) 440–490 (227–254) 440–480 (227–250) Center Zone 560–600 (293–316) 560–615 (293–324) 470–510 (243–266) 460–510 (238–266) Front Zone 580–620 (304–327) 590–630 (310–333) 490–540 (254–282) 480–520 (250–271) Nozzle 575–615 (302 –324) 600–625 (316–330) 520–570 (271–300) 500–530 (260–277) Melt Temperature °F (°C) 575–615 (302–324) 600–625 (316–330) 520–570 (271–300) 500–530 (260–277) Mold Temperature °F (°C) 250–300 (121–150) 250–300 (121–150) 150–200 (66–93) 150–200 (66–93) Pack and Hold Pressure 50–80% of Injection Pressure Injection Velocity 1.0–3.0 in/sec Back Pressure 25–100 psi Screw Speed 25–75 rpm Drying Parameters °F (°C) 6 hours @ 175 (80) 6 hours @ 300 (150) 3 hours @ 180 (82) 3 hours @ 180 (82) Cushion 0.125–0.250 in Screw Compression Ratio 2.5:1–3.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose Reverse Taper Reverse Taper Clamp Pressure 4–5 tons/in2 of projected area of cavities and runner system * Barrel temperatures should be elevated for compounds designed for electrical insulative properties.

Melt temperature 150° C Trackifier Resin Aquamix 814 60 Phenolic Resin. Melt temperature 90° C Wingtack® 95 Aquamix 789 50 Hydrocarbon resin. Melt temperature 90° C Wingtack® 95 Aquamix 789 50 Hydrocarbon resin.

% Pigment Specific Gravity Color Index Lightfastness WHITE 10EPX03 Titanium Dioxide, Rutile 57 1.95 PW-6 I/O YELLOW 12EPX01 Diarylide AAOT GS 25 1.22 PY-14 I 12EPX03 Diarylide HR RS 20 1.2 PY-83 I/O (Mass) 13EPX02 Isoindolinone RS 30 1.3 PY-110 I/O 13EPX03 Benzimidazolone GS 40 1.27 PY-151 I/O (Mass) 81EPX01 Iron Oxide 40 1.62 PY-42 I/O ORANGE 15EPX03 Benzimidazolone 30 1.26 PO-36 I/O RED 23EPX04 Quinacridone BS 25 1.21 PV-19 I/O 23EPX06 Specialty Naphthol BS 30 1.21 PR-170 I/O (Mass) C 25EPX01 Red 2B, Ca Salt Bs 24 1.27 PR-48:2 I/O (Mass) 28EPX01 Red 2B, Ba Salt YS 23 1.29 PR-48:1 I/O (Mass) 82EPX01 Iron Oxide, Light BS 40 1.67 PR-101 I/O 82EPX02 Iron Oxide, Dark BVS 40 1.68 PR-101 I/O 82EPX04 Iron Oxide, Light VYS 40 1.67 PR-101 I/O BLUE 40EXP03 Phthalocyanine GS 25 1.25 PB-15:3 I/O 40EXP05 Phthalocyanine RS 25 1.25 PB-15:3 I/O 42EXP02 Ultramarine 50 1.54 PB-29 I/O 49EXP01 Cobalt 50 1.83 PB-28 I/O GREEN 50EPX02 Phthalocyanine BS 18 1.34 PG-7 I/O 50EPX03 Phthalocyanine YS 25 1.42 PG-7 I/O 59EPX01 Chromium Oxide 40 1.64 PG-17 I/O VIOLET/MAGENTA 24EPX03 Quinacridone Violet 15 1.2 PV-19 I/O 24EPX04 Ultramarine Violet 50 1.66 PV-15 I/O 24EPX05 Quinacridone Magenta 20 1.21 PR-122 I/O 24EPX06 Benzimidazolone 20 1.2 PV-32 I/O 24EPX07 Carbazole Violet 15 1.2 PV-23 I/O BROWN/TAN 83EPX01 Iron Oxide, Light 39 1.64 PBr-6 I/O 83EPX02 Iron Oxide, Dark 40 1.66 PBr-6 I/O BLACK 90EPX01 Furnace - High Jet 14 1.23 PBk-7 I/O 90EPX04 Furnace - Medium 20 1.25 PBk-7 I/O 90EPX05 Iron Oxide 50 1.77 PBk-11 I/O EPX RS = Red Shade YS = Yellow Shade VYS = Very Yellow Shade BS = Blue Shade VBS = Very Blue Shade GS = Green Shade HR = Heat-Resistant LIGHTFASTNESS I = Indoor Only I/O = Indoor or Outdoor Mass = Outdoor Masstone Application Only C = Some Caution Advised www.avient.com Copyright © 2020, Avient Corporation.

• Stable and controlled dielectric constant - from 2.6 to 23 • Very low losses even at mmWaves • Isotropic material - no glass fibers • Can be injection molded and machined APPLICATION BULLETIN STABLE RF PROPERTIES OVER A WIDE FREQUENCY RANGE 0,0 2,0 4,0 6,0 8,0 10,0 12,0 0 10 20 30 40 50 60 D ie le ct ri c co ns ta nt F requency [GHz ] PR E PE RM® PPE 95 0 PR E PE RM® PPE 80 0 PR E PE RM® PPE 44 0 PR E PE RM® PPE 32 0 PR E PE RM® PPE 26 0 LOW LOSSES UP TO mmWAVE FREQUENCIES* BATCH-TO-BATCH STABILITY DURING PRODUCTION * Measurements performed at VTT Technical Research Centre of Finland Ltd in 2018. Di el ec tr ic co ns ta nt Lo ss ta ng en t Di el ec tr ic co ns ta nt Frequency [GHz] Frequency [GHz] Pallet number (1250 kg/pallet) PREPERM™ PPE950 PREPERM™ PPE800 PREPERM™ PPE440 PREPERM™ PPE320 PREPERM™ PPE260 -- Dielectric constant target -- +/- 2% 3,76 3,78 3,80 3,82 3,84 3,86 3,88 3,90 3,92 3,94 0 1 2 3 4 5 6 7 8 D ie le ct ri c co ns ta nt P a llet number (1250 k g/pa llet ) Die le ctric cons ta nt ta rge t +/- 2 % 0,000 0,002 0,004 0,006 0,008 0,010 0 10 20 30 40 50 60 Lo ss t a ng en t F requency [GHz ] PR E PE RM® PPE 95 0 PR E PE RM® PPE 80 0 PR E PE RM® PPE 44 0 PR E PE RM® PPE 32 0 PR E PE RM® PPE 26 0 0,000 0,002 0,004 0,006 0,008 0,010 0 10 20 30 40 50 60 Lo ss t a ng en t F requency [GHz ] PR E PE RM® PPE 95 0 PR E PE RM® PPE 80 0 PR E PE RM® PPE 44 0 PR E PE RM® PPE 32 0 PR E PE RM® PPE 26 0 0,000 0,002 0,004 0,006 0,008 0,010 0 10 20 30 40 50 60 Lo ss t a ng en t F requency [GHz ] PR E PE RM® PPE 95 0 PR E PE RM® PPE 80 0 PR E PE RM® PPE 44 0 PR E PE RM® PPE 32 0 PR E PE RM® PPE 26 0 Copyright © 2022, Avient Corporation.

DOCUMENT NUMBER_ SSS-003 CATEGORY DETAIL EC Number 215-175-0 CAS Number 1309-64-4 Name Subclass 1 Antimony Trioxide (ATO) Structural Formula CHEMICAL IDENTITY PROPERTY DETAIL Physical State Solid Form Powder Color White Odor Odorless Melting Point 656°C Boiling Point 1425°C Bulk Density 5.20 g/cm3 Water Solubility Slightly Soluble PHYSICAL/ CHEMICAL PROPERTIES DOCUMENT NUMBER_ SSS-003 HEALTH EFFECTS HUMAN HEALTH SAFETY ASSESSMENT Consumer It is very unlikely that consumers would be exposed to ATO in its concentrated form because it is only sold for industrial use to make polymers and other products and is not sold directly to consumers.

Mulch films case study BIODEGRADABLE & COMPOSTABLE M U L C H F I L M S • Compliance with European Standard EN17033 or OK Compost • Black and white color standards available under different TÜV Austria certifications (OK Compost and more) • Full support for end-product certification for both EN13432 and EN17033 • Formulated with pigments tested and approved by certified body OnColor™ Bio-Colorants KEY REQUIREMENTS WHY AVIENT?

See Annex C for examples of information that may be considered Inside Information. Pre-arranged Trading Plans: An SEC rule, Rule 10b5-1(c), provides a defense from insider trading liability if trades occur pursuant to a pre-arranged “trading plan” that meets specified conditions. Please note that, in addition to the requirements of a trading plan described above, there are a number of additional procedural conditions to Rule 10b5-1(c) that must be satisfied before you can rely on a trading plan as an affirmative defense against an insider trading charge.

ET9600-8010 LDS ET3200-8177 LDS Dielectric Constant (DK) 3.98 2.88 Dissipation Factor (Df) 0.0060 0.0040 SPECIALTY ENGINEERED MATERIALS ELECTRICAL & ELECTRONICS SOLUTIONS EDGETEK™ FORMULATIONS FOR 5G BASE STATION ANTENNA APPLICATIONS EDGETEK™ PRODUCT PORTFOLIO HOW AVIENT EDGETEK FORMULATIONS MAKE THE DIFFERENCE FOR 5G BASE STATION ANTENNA APPLICATIONS Increased Design Flexibility – Can increase design flexibility especially for circuit design, 3D antenna design, and complex shapes Faster Design Qualification & Shorter Lead Time – Can be customized to specific Dk values and delivered within weeks Flexible Design Space – Effective for circuit designs constrained by a limited space Compatible with SMT Process – Can be customized to resist heat, with deflection temperatures ranging from 200°C to 278°C To learn more, please visit www.avient.com or call +86.21.60284888. www.avient.com Copyright © 2020, Avient Corporation.