可根据要求提供FDA/EU合规信息 1.844.4AVIENT www.avient.com 版权所有© 2022埃万特公司。

回收应用 APR认证 2021 2021 1.844.4AVIENT www.avient.com 版权所有©2021 埃万特公司。

www.avient.com 版 权 所 有 © 2020埃 万 特 公 司 。

1.844.4AVIENT www.avient.com 版权所有© 2021埃万特公司。

Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase injection rate • Increase mold temperature Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Process related • Increase cooling time • Increase melt temperature • Increase pack pressure • Increase pack time • Decrease mold temperature Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Processing Guide 7 Troubleshooting Recommendations Problem Cause Solution Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease pack and hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Mold design • Increase draft angle• Polish cores in direction of ejection Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

关键性能 加工信息 1 1 物理性能 标称值 标称值 单位 测试法 1.00 ASTM D792 20 g/10 min ASTM D1238 抗拉强度 密度/比重 熔指 (MFR) (230°C/2.16kg) 15.0 MPa ASTM D638 1400 MPa ASTM D790 35.0 MPa ASTM D790 150 J/m ASTM D256 < 100000 ohms/sq ASTM D257 80 to 90 °C 4.0 to 6.0 hr 220 to 250 °C 30 to 80 °C 机械 弯曲模量 弯曲强度 悬臂梁缺口冲击强度（注塑样条） 冲击 电气 表面电阻率 干燥温度 注塑 干燥时间 加工（熔化）温度 模具温度 主要性能：不能被解释为技术指标 单位 Trilliant HC™ 方案如何协助攻克严苛的性能和工艺挑战 www.avient.com 版权所有©2022 埃万特公司。

Wire _ Cable Selection Guide_CN 11.09-1 电线 & 电缆 解决方案 特种工程材料 产品选择指南 用于电线与电缆行业的 高性能绝缘材料、护套和交联配方 Syncure™ XLPE 交联聚乙烯配方 室温自然交联 阻燃 耐热、耐油、抗蠕变和耐磨 低温特性 设备投入低 高速挤出 拥有不含十溴二苯烷产品规格 UL/ CSA 公告 · · · · · · · · ECCOH™ 低烟无卤配方 防火安全 低烟，无卤配方（LSFOH） 耐化学品 · · · Maxxam™ FR 阻燃聚乙烯配方 替代FEP 耐火性 阻燃性-UL 444 & 阻燃黄卡 低介电性 高速挤出 薄壁挤出 · · · · · · ECCOH™ XL 交联解决方案 无卤，低烟，低毒，低腐蚀性 优异的机械性能 & 导电性能 易于加工 90℃的工作温度 室温自然交联 · · · · · Maxxam™ SY 发泡阻燃配方 低介电 均匀的发泡 抗冲击、耐热 易于化学发泡 · · · · FireCon™ CPE 绝缘护套配方 适用于恶劣环境 低温性能 阻燃 高速挤出 耐日光 · · · · · Synprene™ 阻燃热塑性弹性体 柔性 阻燃 抗低温脆化（LTB） 耐化学品 易于着色 · · · · · 阻燃 耐热、耐油、耐蠕变、耐磨损 耐低温 资本投入低 高速挤出 · · · · · 低压电力电缆 横向火焰 UL 44Syncure™ S100FH Syncure™ S100FH-XUV 横向火焰，抗紫外线 横向火焰、FV-1火焰、抗紫外线 VW-1火焰 VW1、抗紫外线 非阻燃 非阻燃 横向火焰，不含DBDPE UL 44 UL 44、UL 4703 UL 44 UL 44 CSA 22.2 NSF 61 UL 44 电力电缆系统绝缘 特点 规格 Syncure™ S100FH-UV Syncure™ S100FV Syncure™ S100FV-UV Syncure™ S112NA Syncure™ S120NA VW-1，不含DBDPE UL 44Syncure™ S200FV Syncure™ S200FH 低烟无卤、低毒性、耐腐蚀 EN50618ECCOH™ XL 8148 FEP替代品 阻燃 介电常数低 高挤出速度和薄壁性能 耐化学性 耐低温 灵活性高 · · · · · · · 分类电缆 数据电缆系统的绝缘和交叉网 卤素到全空气性能 UL 444Maxxam™ FR 0587-21 R3 特点 规格 低烟无卤 UL 444Maxxam™ FR 0521-48 R1 特点 规格 可发泡 满足客户特定的阻燃要求Maxxam™ SY 89-22-7 耐恶劣环境、化学品和阳光照射 耐低温脆性（LTB） 低烟低毒 灵活性高 高速挤出 · · · · · 光纤电缆 特点 规格 低烟雾、无卤 满足客户特定的阻燃要求ECCOH™ 6649 UV Low DD 灵活性高 高速挤出 介电常数低 单元结构均匀 耐压耐热 · · · · · 同轴电缆 阻燃、柔性 建筑和工程、工业、核能FireCon™ CPE 37-36 RoHS 黑色 FireCon™ CPE 30-20 RoHS 自然色 阻燃、柔性 低烟、无卤、阻燃 低烟、无卤、阻燃 低烟、无卤、阻燃 阻燃，抗LTB 阻燃，抗LTB 阻燃，抗LTB 建筑和工程、工业、核能 建筑和工程、工业 光纤、管道 工业, Teck 90电线 建筑和工程、工业 建筑和工程、工业 建筑和工程、工业 特点 细分市场和用途 ECCOH™ 5549 UV ECCOH™ 6649 UV Low DD ECCOH™ 5981 UV Synprene™ RT5180 Synprene™ RT5180UV Synprene™ RT3870M 阻燃、柔性 建筑和工程、工业、核能FireCon™ CPE 30-33 RoHS 黑色 耐恶劣环境、化学品和紫外线降解 耐低温脆性（LTB） 低烟低毒 灵活性高 高速挤出 易着色 · · · · · · 低压和中压护套 电力和数据电缆系统护套 +86 021 60284888 www.avient.com 版权所有©2023埃万特公司。

Sink Marks Melt too hot • Decrease nozzle and barrel temperatures• Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Troubleshooting Recommendations Problem Cause Solution Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height• Increase clamp tonnage Shrink Too much shrink • Increase cooling time• Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents• Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Problem Cause Solution Warp Process related • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Troubleshooting Recommendations Processing Guide 7 Troubleshooting Recommendations Problem Cause Solution Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

Sink Marks Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold temperature too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Warp Process related • Increase melt temperature • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding TROUBLESHOOTING RECOMMENDATIONS 1.844.4AVIENT www.avient.com Copyright © 2021, Avient Corporation.

PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection speed • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low Mold design • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Increase mold temperature • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation Mold design • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Mold design Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Mold design Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase shot size • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase shot size • Increase injection rate • Increase packing pressure • Increase gate size Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS www.avient.com Copyright © 2020, Avient Corporation.