Si no se le piden y si decide transmitirnos este tipo de datos durante el proceso de solicitud, nos reservamos el derecho de eliminar dichos datos de nuestras bases de datos. 2. Ejemplo: está solicitando un puesto en PolyOne Canada, Inc. En la tramitación de su solicitud participan miembros del departamento responsable en los Estados Unidos (Avient Corporation) y, por norma, del departamento de recursos humanos en Canadá (PolyOne Canada, Inc.).

Dove non richiesto, se decidi di trasmetterci questo tipo di dati durante il processo di candidatura, ci riserviamo il diritto di eliminarli dai nostri database. 2. Esempio: ti stai candidando per una posizione presso PolyOne Canada, Inc. I componenti del dipartimento responsabile negli Stati Uniti (Avient Corporation) e, naturalmente, l'ufficio risorse umane in Canada (PolyOne Canada, Inc.) sono coinvolti nella gestione della tua domanda.

AMBER PETG 2 186C RED 2 PE UV ORANGE

6163-2 BLACK SPARKLE 2 BLACK STREAKER UV UV WEATHERWOOD PE

What is left is; one true white, one true black, and all other colors falling into shades of gray. Halftone white on Black substrate Once printed on the black fabric, it will appear gray in color.

Right: Avient associates participating in a career fair at the National Black MBA Conference. The most advanced LSS training is for Black Belt level project leaders. Smartbatch™ Color And Additive Concentrates offer superior UV weathering protection for solar power installations.

Wednesday, November 2, 2022 Wednesday, November 2, 2022 A recording of the webcast and the slide presentation will be available at avient.com/investors/events-presentations immediately following the conference call and will be accessible for one year.

BASE RESIN ABS Drying Temperature 80–90°C Drying Time 2–3 Hours Barrel Temperatures °C Rear Zone 180–210 Center Zone 190–220 Front Zone 200–230 Nozzle 210–240 Mold Temperature 50–80 Screw Speed Moderate Back Pressure 3–10 bar Cushion 5–15 mm Injection Speed Low to medium Injection Pressure Moderate to high Holding Pressure 10–30% of injection pressure Screw Type General purpose Screw L/D 20:1 Screw Compression Ratio 2.0:1–2.5:1 Non-return Check Valve Free flow check ring Nozzle Type Reverse taper Barrel Capacity 30–80% of barrel should be used STARTUP & SHUTDOWN RECOMMENDATIONS Purge Compound 2–3 melt flow PP or purging compound. HDPE is not recommended for purging as it can cause delamination or lead to black specks. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold temperature too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Warp Process related • Increase melt temperature • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding TROUBLESHOOTING RECOMMENDATIONS 1.844.4AVIENT www.avient.com Copyright © 2021, Avient Corporation.

BLACK CC 709 BLACK BLUE UV

BLACK PE BLACK PE WHITE INHALER 2