Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

Color effects are suggested based on several criteria, including: • Specific applications • Ability to execute the effect in distinct resin grades • Performance requirements of the application If you do not see the color effect you are looking for, please contact us to collaborate on a solution. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

INDUSTRY BULLETIN Cesa™ Laser Additives Laser Marking Solutions for the Transportation Industry Many thermoplastic automotive parts require a permanent marking, and laser marking is among the most efficient means to do so. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. CAUSE AND EFFECT DIAGRAM Methods Machines Materials Manpower Variable energy saving during SBM Maintenance instructions Operating instructions Faulty Operator Job spec NIR Lamps SBM Type/Design vPET reheat content vPET formulation rPET blend/quality Temperature recording Temperature measurement probe External temperature Faulty Incomplete Inappropriate Incomplete Incomplete Different Different Different Manual Different Variable Variable Variable Training New Faulty Alignment Same Throughput Too many tasks Time conflict Age/intensity variable Set up conditions Configuration - When starting to process a new resin, first run through new preforms for 15 minutes at ‘standard’ conditions to establish steady state conditions prior to any process optimization - Slowly start to reduce preform blowing temperatures until failures are present (visible pearl internal wall or pearl feet) - Increase blowing temperatures until defects are eliminated - QC check bottle quality for acceptance versus established tolerances - Change the power consumption profile in the ovens for early heat and longer sink times but ensure overall temperatures do not exceed cold crystallization temperature - Repeat temperature reduction stage and then defect elimination stage to test if further optimization is possible - Recheck QC bottle quality for acceptance versus established tolerances - Log all process parameters and create new specific ‘recipe’ for future use

To do so, three pieces of bottle walls were stacked for this measurement and referred to as first melt history. To do so the following procedure was carried out: • Preforms were produced by dosing 0.09% of Avient Fortis Amber-1 and 4% of our nylon- based oxygen scavenger Amosorb SolO2-2 • Preforms were ground down to a coarse granule size (~2mm) using a Retsch mill • The coarse ground preforms were crystallized in a vacuum oven at 160°C before drying the material in a PET drier at 160°C for approx. 4 hours • This material was then injection molded and blown into bottles with a) 50:50 dilution with Virgin PET with no color and b) 50:50 dilution with Virgin PET + Fortis Amber-1 at 0.045% Figure 2. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

Alleged claims, if any, do not affect Buyer’s obligation to pay for the conforming portion of the Products delivered. Should the arbitrator fail to do so then, subject to the other provisions of these Terms, each party shall bear its own costs, however the parties shall share the fees and expenses of the arbitrator equally. Each Party shall when Processing any Personal Information supplied by either party to the other, comply with all applicable industry codes of conduct to the extent that they regulate the Processing of Personal Information and not do anything, or omit to do anything, which will cause the other Party to contravene any applicable laws, including any Data Protection Legislation.

Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

Supplier adherence to our values We are committed to doing business the right way, including without limitation, conducting business ethically and minimizing the risk of slavery and human trafficking in our own business and in that of our suppliers as much as possible. We are committed to doing business the right way, including without limitation, conducting business ethically and to minimizing the risk of slavery and human trafficking in our own business and in that of our suppliers as much as possible This statement is approved by ColorMatrix by its board of directors.

Recess holes are recommended so that fluids do not ingress. Gussets are used to support a boss because they do not cause thick sidewall regions. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

To the extent to which Seller’s and Buyer’s trade terms and conditions do contradict each other, the general provisions of legal regulations shall be applied. 2. Alleged claims, if any, do not affect Buyer’s obligation to pay for the conforming portion of the Products delivered. Unless otherwise agreed in a writing signed by Seller, Seller may make changes to its Product and process without notice to, or approval from, Buyer so long as the Product Specifications do not change and the Product conforms to such Specifications.