Drying non-halogenated materials is suggested. 2 hours @ 100 (38) Moisture Range (%) Not required Tool Steel • P20 tool steel is acceptable when proper processing and shut down procedures are followed • Chrome plating or PH stainless steel is preferred for all halogen-based systems • The use of stainless steel in hot runner systems is highly suggested • Avoid the use of aluminum when designing production tools Vents • Place vents at the end of fill and anywhere potential knit/weld lines will occur • All vents need to be vented to atmosphere • Cut vent depths to 0.0010"–0.0015" with a minimum 0.040" land length. Increase the vent depth to 0.010" at 0.100" away from the cavity and vent to atmosphere. • Vents should be placed at the intersection of each 90° bend in the runner system off of the cold slug well and vented to atmosphere PROBLEM CAUSE SOLUTION Black Specks Contamination • Purge barrel with general purpose PP • Verify correct nozzle is being used • Pull screw for cleaning Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded-in stress Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed Insufficient packing • Increase hold pressure and time • Increase shot size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Troubleshooting Recommendations PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full • Increase shot size Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Troubleshooting Recommendations (continued) PROBLEM CAUSE SOLUTION Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Warp Process related • Increase cooling time • Increase melt temperature • Increase pack pressure • Increase pack time • Decrease mold temperature Mold design • Inspect for non-uniform mold cooling Part design • Inspect for non-uniform wall thickness Temperature control unit incorrect temperature • Check settings • Inspect thermocouple Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase injection rate • Increase mold temperature Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

A PLATINUM VISION FOR THE FUTURE While no doubt a successful year, 2014 is history. Check one): Large accelerated filer Í Accelerated filer ‘ Non-accelerated filer ‘ Smaller reporting company ‘ (Do not check if a smaller reporting company) Indicate by check mark whether the registrant is a shell company (as defined in Rule 12b-2 of the Exchange Act). Level 1 assets are valued based on quoted market prices.

Factors that could cause actual results to differ materially from those implied by these forward-looking statements include, but are not limited to: • The time required to consummate the proposed acquisitions described in this presentation; • The satisfaction or waiver of conditions in the purchase agreements for the proposed acquisitions; • Any material adverse changes in the business of Clariant’s Color and Additive Masterbatch business; • The ability to obtain required regulatory or other third-party approvals and consents and otherwise consummate the proposed acquisitions; • Our ability to achieve the strategic and other objectives relating to the proposed acquisitions, including any expected synergies; • Our ability to successfully integrate Clariant’s Color and Additive Masterbatch business and achieve the expected results of the acquisitions, including, without limitation, the acquisitions being accretive; • Disruptions, uncertainty or volatility in the credit markets that could adversely impact the availability of credit already arranged and the availability and cost of credit in the future; • The effect on foreign operations of currency fluctuations, tariffs and other political, economic and regulatory risks; • Changes in polymer consumption growth rates and laws and regulations regarding plastics in jurisdictions where we conduct business; • Changes in global industry capacity or in the rate at which anticipated changes in industry capacity come online; • Fluctuations in raw material prices, quality and supply, and in energy prices and supply; • Production outages or material costs associated with scheduled or unscheduled maintenance programs; • Unanticipated developments that could occur with respect to contingencies such as litigation and environmental matters; • An inability to raise or sustain prices for products or services; • An ability to achieve or delays in achieving or achievement of less than the anticipated financial benefit from initiatives related to acquisition and integration, working capital reductions, costs reductions and employee productivity goals; • Information systems failures and cyberattacks; and • Other factors affecting our business beyond our control, including, without limitation, changes in the general economy, changes in interest rates and changes in the rate of inflation. Each of such adjustments has not yet occurred, are out of the Company's control and/or cannot be reasonably predicted. Richardson Executive Vice President and Chief Financial Officer PolyOne Corporation 4 PolyOne Corporation 5  Landmark portfolio transformation: > 85% of Adjusted EBITDA from specialty solutions  World-class innovation, technology and service are differentiators  Sustainability initiatives and alignment with megatrends drive above market growth in key end markets and applications:  Capital management is a strength - proven track record of expanding ROIC while increasing invested capital Transaction expected to add $0.85 to pro forma adjusted EPS T H E N E W P O L Y O N E : A S P E C I A L T Y G R O W T H C O M P A N Y Integrity V I S I O N PolyOne Corporation 6 To be the world’s premier provider of specialized polymer materials, services and solutions C O R E V A L U E S P E R S O N A L V A L U E S Honesty Respect Operational Excellence Commercial Excellence Specialization Globalization Collaboration ExcellenceInnovation To be the world’s premier provider of sustainable, specialty polymer materials and solutions.

Rev 12-05-2023 Avient Corporation: Quality Response for Manufacturing Facilities in North America, North LATAM, Europe, the Middle East, and Africa 2 Dear Customer, This Quality Response for Manufacturing Facilities in North America, Europe, the Middle East and Africa, is being provided in response to your request to complete and return your supplier questionnaire / assessment. While we believe the information contained in this document should be responsive to most inquiries, if you have questions not answered by this document you should reach out to your sales representative, who is your primary contact, and can forward your request to an appropriate person. Please check our certificate library here.

N95 masks, for example, rely on multi-layer construction, with a middle layer made from melt-blown non-woven material. With proper ingredient selection and processing, MagIQ Non-Woven Electret Additives helped the middle layer of these protective masks effectively trap particles as small as 0.3 microns.

N95 masks, for example, rely on multi-layer construction, with a middle layer made from melt-blown non-woven material. With proper ingredient selection and processing, MagIQ Non-Woven Electret Additives helped the middle layer of these protective masks effectively trap particles as small as 0.3 microns.

N95 masks, for example, rely on multi-layer construction, with a middle layer made from melt-blown non-woven material. With proper ingredient selection and processing, MagIQ Non-Woven Electret Additives helped the middle layer of these protective masks effectively trap particles as small as 0.3 microns.

And it needed to match the Audi Q5 interior colors while offering protection from both direct and indirect sunlight. It offered low-temperature flexibility, good abrasion resistance, excellent colorability, and resistance to attack from UV radiation – ticking off every check box on the Jäger team’s wish list.

MIDDLE MIDDLE MIDDLE

WHITE MIDDLE V1 WHITE MIDDLE V4 WHITE MIDDLE V6