A schematic diagram of this test procedure is shown in figure 1. Figure 1: Schematic diagram of peel adhesion testing. Table 1: Physical properties of developed overmold compounds.

BARREL TEMPERATURES ENGLISH (°F) METRIC (°C) COMMENTS Zone 1 - Rear 420° F 460° F 216° C 238° C Long residence times are not advised. Screw Speed Low–moderate Injection Velocity 1–3 inch per second Back Pressure Low–moderate Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) Residence Time Long residence times are not advised 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

Selected for their strong performance and durability, phthalates are the most commonly used plasticizers in the world.1 In recent years, concerns have been raised over the use of phthalates, giving rise to myths and unfounded speculation. PHTHALATES FACTS PHTHALATES ARE KNOWN TO BREAK DOWN IN THE HUMAN BODY Research has shown that after entering the body, phthalate are broken down into metabolites within minutes and pass out quickly in urine.2 PHTHALATE EXPOSURE IS CONSIDERED LOW Despite the fact that phthalates are used in a wide range of products, human exposure from all sources is considered to be extremely low.2 PHTHALATES ARE A USEFUL CHOICE FOR HEALTHCARE Flexible vinyl tubing does not react with most medications, allowing for reliable administration of drugs, while flexible vinyl bags prevent blood contamination and extend shelf life of the blood.3 PHTHALATES ARE REGULATED Based on earlier studies, a few specific phthalates have been banned for use in toys or other items for sale to children under twelve to reduce risk of overexposure through hand-to- mouth behaviors. 1 Source: chemicalsafetyfacts.org 2 Source: Centers for Disease Control and Prevention 3 Source: thisisplastics.com www.avient.com Copyright © 2020, Avient Corporation.

BARREL TEMPERATURES ENGLISH (°F) METRIC (°C) COMMENTS Zone 1 - Rear 410°F 450°F 210°C 230°C If smoking starts to occur, purge machine immediately and reduce mold and barrel temperatures. DRYING CONDITIONS ENGLISH (°F) METRIC (°C) Temperature 180°F 80°C Duration 2–4 Hours Moisture Level Allowable 0.05%–0.20% PROCESSING Screw Speed Typical screw speeds are recommended Injection Velocity 1–3 inch per second Back Pressure Lower back pressure is recommended Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) Residence Time Longer residence times are not advised 1.844.4AVIENT www.avient.com Copyright © 2021, Avient Corporation.

To access Avient’s news library online, please visit www.avient.com/news # # # Investor Relations Contact: Giuseppe (Joe) Di Salvo Vice President, Treasurer and Investor Relations +1 440-930-1921 giuseppe.disalvo@avient.com Media Contact: Kyle G. Rose Vice President, Marketing and Communications +1 440-930-3162 kyle.rose@avient.com http://www.avient.com/ http://www.avient.com/news mailto:giuseppe.disalvo@avient.com mailto:kyle.rose@avient.com

Guided by their initiative to develop capabilities that provide additional protection for soldiers while reducing time and logistic requirements,1 the U.S. With our hardware fabrication capabilities and Avient’s knowledge of composite ballistic protection technology, we were able to create modular systems that reduce time and logistic requirements for our brave soldiers.” 1 https://www.erdc.usace.army.mil/Missions/Military-Engineering/Deployable-Force-Protection-Demo/ To learn more about ballistic resistant solutions from Avient, visit avient.com or click to request a quote.

The resulting tensile test data shown in Figure 1 gives an indication of the variation in material response that can be observed as a function of the fibre orientations. In reality, the material response can fall anywhere between the curves shown in Figure 1. Figure 1: Tensile test data as a function of the fibre orientation 0° (orange), 45° (green), 90° (blue) https://www.hexagonmi.com Figure 4: Failure location in the flexural test for the isotropic modelling Figure 6: Failure location in the tensile test for the isotropic modelling approach (left), Digimat anisotropic modelling approach (middle) and reality (right) Figure 3: Flexural test results with the isotropic modelling approach (orange) and Digimat anisotropic modelling approach (green) Figure 5: Tensile test results with the isotropic modelling approach (orange) and Digimat anisotropic modelling approach (green) Figure 5 shows the tensile test results with, again, a convincing advantage for the Digimat anisotropic modelling approach against the isotropic modelling approach.

1 How to create invoices through the Coupa Supplier Portal (CSP) Suppliers Guide For Avient Suppliers View and Manage Invoices In order to view your Invoices page, click on the Invoices tab on the main menu. Click on the relevant button above the Invoices table to: ➢ Create Invoice from PO ➢ Create Credit Note Create an invoice from a PO 1. To create a credit note: 1.

HMPE for example, has a specific gravity less than 1 and will float in water. • Corrosion Since our products are non-corrosive, they offer outstanding performance in corrosive environments, including marine and off- shore applications. • Conductivity High-performance synthetic fibers act as a barrier between eletrical components. • Creep When exposed to static long-term loads, synthetic fibers stretch very little. POPULAR COATED STRENGTH MEMBERS MOVING HIGH PERFORMANCE FIBERS FORWARD LOCATIONS Headquarters, R&D, Manufacturing FIBER-LINE® LLC 3050 Campus Drive Hatfield, PA 19440 +1 215.997.9181 fiber@fiber-line.com Manufacturing Operations FIBER-LINE® LLC 280 Performance Drive SE Hickory, NC 28602 +1 828.326.8700 fiber@fiber-line.com EMEA & Asia Pacific Operations FIBER-LINE® INTERNATIONAL B.V.

Consequentially many brand owners are already looking to reduce the inorganic content in their packaging to TECHNOLOGY BENEFITS • Improved light blocking performance up to 99.9% at 550nm and 700nm • Brighter whiteness L* >90 even in thin wall sections (0.21mm) • Plug & go solution—processes similar to virgin PET • Process with standard PET grades and rPET • Reduces equipment wear and tear • TiO2 content of This literature shall NOT operate as permission, recommendation, or inducement to practice any patented invention without permission of the patent owner. 1.844.4AVIENT www.avient.com PROPERTIES LACTRA™ FOUR LACTRA™ ONE LACTRA™ ZERO TiO2 % in bottles at UHT LDR 3% 1% 0% Recommended LDR for UHT 10% 7% 10% Light blocking at 550nm at UHT LDR >99.9% >99.8% >99.9% Light blocking at 700nm at UHT LDR >99.9% >99.8% >99.9% Color L* >90 >88 >90 COLORMATRIX LACTRA LOW-TIO2 RANGE