Sink Marks Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold temperature too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Warp Process related • Increase melt temperature • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding TROUBLESHOOTING RECOMMENDATIONS 1.844.4AVIENT www.avient.com Copyright © 2021, Avient Corporation.

REGULATORY 1.844.4AVIENT www.avient.com Copyright © 2023, Avient Corporation.

Código de conducta para proveedores de Avient Avient Corporation y sus subsidiarias y filiales (“Avient”) se comprometen a ser una organización sostenible de categoría mundial.

Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase injection rate • Increase mold temperature Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Process related • Increase cooling time • Increase melt temperature • Increase pack pressure • Increase pack time • Decrease mold temperature Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Processing Guide 7 Troubleshooting Recommendations Problem Cause Solution Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease pack and hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

% Pigment Specific Gravity Color Index Heat Stability Lightfastness System BROWN 83MB01 (c) Iron Oxide, Tan HR 60 1.78 PBr-11 1 I/O SBR 83MB02 (c) Iron Oxide, Light 68 2.1 PBr-6 2 C I/O SBR 83MB03 (c) Iron Oxide, Dark 60 1.83 PBr-6 2 C I/O SBR 83EP02 Iron Oxide, Light 69 1.98 PBr-6 2 C I/O EPDM 83EP03 Iron Oxide, Dark 69 1.98 PBr-6 2 C I/O EPDM BLACK 90MB01 (c) Furnace N-330 31 1.2 PBk-7 1 I/O SBR 90MB05 (c) Iron Oxide 60 1.8 PBk-11 2 C I/O SBR 90EP01 Furnace Black 33 1.05 PBk-7 1 I/O EPDM 90EP05 Iron Oxide 55 1.56 PBk-11 2 C I/O EPDM ALUMINUM 61MB01 Aluminum 70 1.5 PM-1 1 I/O SBR 61EP01 Aluminum 60 1.31 PM-1 1 I/O EPDM RS = Red Shade YS = Yellow Shade VYS = Very Yellow Shade BS = Blue Shade VBS = Very Blue Shade GS = Green Shade NC = Non-Crystallizing HR = Heat-Resistant (a) = Potential Migration at Low Use Levels (b) = Poor Alkali Resistance - Not Recommended for Open Steam Cure (c) = Six Month Shelf Life LIGHTFASTNESS I = Indoor Only I/O = Indoor or Outdoor Mass = Outdoor Masstone Application Only C = Some Caution Advised HEAT STABILITY 1 = Above 400°F 2 = 350°F–400°F 3 = Below 350°F C = Some Caution Advised 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

詳情載 於 The Loop 上的《全球隱私與資料保護政策》，位於「People & Departments, Ethics & Corporate Policies」。 詳情載於 The Loop 上的《資訊系統使用政策》，位於「People & Departments, Ethics & Corporate Policies」。 您可以在 The Loop 找到，位於「People & Departments, Ethics & Corporate Policies」下。

These Terms and Conditions (“Terms and Conditions”) shall apply to any and all sales of products (“Products”) of PolyOne Corporation and its affiliates ("Seller") to third parties (“Buyer”). 1. Estes Termos e Condições (“Termos e Condições”) aplicam-se a todas e quaisquer vendas de produtos (“Produtos) da PolyOne Corporation e suas afiliadas (“Vendedor”) a terceiros (“Comprador”). 1.2.

ESCR Design Guide 6 FIGURE 17 - Non-structural hole design guidelines 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

FASTENER TYPE BENEFITS CONSIDERATIONS FOAM HONEY COMB Through- bolting Best mechanical locking system Need back side access to panel ✓ ✓ Wide Grip (Bulb-Style) Rivet Highest pullout strengths Requires pilot hole ✓ Cup Washer Spreads compressive load Requires relief hole; for substructure and hard point attachment ✓ ✓ Wide Grip (Bulb-Style) Rivet Ease of use— no installation torque limitations For lower load attachments ✓ Sheet Metal or Wood Screw Readily available, low cost Penetrate both skins for improved pullout ✓ Shoulder Washer Limits compressive load Requires relief hole; for substructure and hard point attachment ✓ ✓ FASTENER SELECTION Copyright © 2023, Avient Corporation.

NORTH AMERICA GRADES reSound™ REC VX2800-0003 C 65 Gray reSound™ REC OF 7310-80 reSound™ REC OF 7310-90 reSound™ REC GP 7820-340 reSound™ REC GP 7820-360 reSound™ REC GP 7820-380 Recycled Content PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend PCR/PIR Blend Recycled Content, % 25% 35% 45% 60% 60% 60% Recycled Source Food Packaging Food Packaging Food Packaging Transportation, Industrial Transportation, Industrial Transportation, Industrial Hardness, Shore A 65 80 90 36 63 77 Color Gray Black/Natural (Gray) Black/Natural (Gray) Natural Natural Natural Specific Gravity 0.88 0.9 0.91 0.95 0.98 1.0 Tensile Strength, PSI 831 1120 1590 1027 1012 1173 Elongation at Break, % 620 570 520 1600 1200 1000 Compression Set @ Room Temperature 26 32 37 24 30 39 OM Substrate PP PP PP PP PP PP Processing IM or OM IM IM IM IM IM Agency Rating Application Specific FDA – – – – – Automotive Testing* – VOC & FOG (VDA 278), Odor (VDA 270) VOC & FOG (VDA 278), Odor (VDA 270) – – – reSound™ REC VX7900-5001 C I 30A Natural reSound™ REC VX7900-5001 C I 50A Natural reSound™ REC VX7900-5001 C I 70A Natural reSound™ REC AF 7210-140 B reSound™ REC AF 7210-150 B reSound™ REC AF 7210-160 B reSound™ REC AF 7210-170 B reSound™ REC AF 7210-180 B reSound™ REC AF 7210-190 B Recycled Content PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend PIR/PCR Blend Recycled Content, % 81% 81% 83% 59% 57% 54% 57% 56% 51% PIR Recycled Source Proprietary Blend Proprietary Blend Proprietary Blend Transportation Transportation Transportation Transportation Transportation Transportation PCR Recycled Source Transportation/ Industrial Transportation/ Industrial Transportation/ Industrial Transportation Transportation Transportation Transportation Transportation Transportation Hardness, Shore A 30 50 70 43 51 61 70 81 90 Color Natural Natural Natural Black Black Black Black Black Black Specific Gravity 1.14 1.16 1.16 0.97 0.98 0.98 0.98 0.99 0.99 Tensile Strength, MPa 2.39 3.23 3.35 4 5 5 8 10 13 Elongation at Break, % 796 654 515 1013 993 981 935 876 829 Compression Set @ Room Temperature 16 24 37 41 44 44 48 54 55 OM Substrate PP PP PP PP PP PP PP PP PP Processing IM or OM IM or OM IM or OM IM IM IM IM IM IM EUROPE GRADES reSound™ REC VX2800-5032 C 47A Natural reSound™ REC VX2800-5033 C 54A Natural reSound™ REC GP 7820-140 reSound™ REC GP 7820-160 reSound™ REC GP 7820-180 Recycled Content PCR PCR PCR PCR PCR Recycled Content, % 61% 61% 60% 60% 60% PCR Recycled Source Transportation Transportation Transportation/ Industrial Transportation/ Industrial Transportation/ Industrial Hardness, Shore A 47 54 38 57 77 Color Natural Natural Natural Natural Natural Specific Gravity 0.96 0.96 0.94 0.97 1.0 Tensile Strength, MPa 1.80 2.00 7.19 6.65 7 Elongation at Break, % 766 682 1590 1380 1010 Compression Set @ Room Temperature 28 29 28 32 38 OM Substrate PP PP PP PP PP Processing IM or OM IM or OM IM IM IM EUROPE GRADES ASIA GRADES - PIR reSound™ REC VX3120-801 I 65A Natural reSound™ REC VX3120-802 I 65A Natural reSound™ REC VX3120-803 I 65A Natural Recycled Content PIR PIR PIR Recycled Content, % 20% 40% 60% Recycled Source Textile Industry Textile Industry Textile Industry Hardness, Shore A 67 68 68 Color Natural Natural Natural Specific Gravity 1.11 1.10 1.11 Tensile Strength, PSI 1450 1229 1151 Elongation at Break, % 752 709 653 OM Substrate PC, ABS, PC/ABS PC, ABS, PC/ABS PC, ABS, PC/ABS Processing IM or OM IM or OM IM or OM reSound™ REC DY 7810-801 C 30A Natural reSound™ REC DY 7810-801 C 40A Natural reSound™ REC DY 7810-801 C 50A Natural reSound™ REC DY 7810-801 C 60A Natural reSound™ REC DY 7810-801 C 70A Natural reSound™ REC DY 7810-801 C 80A Natural reSound™ REC DY 7810-801 C 90A Natural reSound™ REC DY 7820-801 C 30A Natural reSound™ REC DY 7820-801 C 40A Natural reSound™ REC DY 7820-801 C 50A Natural reSound™ REC DY 7820-801 C 60A Natural reSound™ REC DY 7820-801 C 70A Natural reSound™ REC DY 7820-801 C 80A Natural reSound™ REC DY 7820-801 C 90A Natural reSound™ REC 3630-801C 40N reSound™ REC 3630-801C 50N reSound™ REC 3630-801C 60N reSound™ REC 7850-90N FR reSound™ REC GP 7820-240 reSound™ REC GP 7820-260 reSound™ REC GP 7820-280 Recycled Content PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR PCR Recycled Content, % 9% 12% 15% 21% 23% 30% 39% 60% 60% 60% 60% 60% 60% 60% 45% 45% 45% 32% 60% 60% 60% Recycled Source Food Packaging Food Packaging Food Packaging Food Packaging Food Packaging Food Packaging Food Packaging Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging, Transportation Food Packaging Transportation, Industrial Transportation, Industrial Transportation, Industrial Hardness, Shore A 30 40 50 60 70 80 90 30 40 50 60 70 80 90 40 49 58 85 39 57 80 Color Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Natural Specific Gravity 0.88 0.89 0.89 0.88 0.88 0.89 0.89 0.95 0.94 0.97 0.97 0.99 1.01 1.02 0.90 0.90 0.90 1.04 0.95 0.98 1.0 Tensile Strength, PSI 678 889 939 964 1057 1328 1619 663 804 830 859 844 1007 1279 830 965 985 1250 938 1089 1479 Elongation at Break, % >1000 983 893 750 726 699 599 1028 948 880 807 681 642 640 700 700 650 310 1600 1360 1090 OM Substrate PP PP PP PP PP PP PP PP PP PP PP PP PP PP PC, ABS, PC/ABS PC, ABS, PC/ABS PC, ABS, PC/ABS – PP 30 39 Processing IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM IM or OM EM IM IM IM ASIA GRADES - PCR Copyright © 2024, Avient Corporation.