CERTIFICATE Signed for the certification body: Eric Louys Chairman Certification Committee CERTIFICATE EN ISO 50001 : 2018 Energy Management System VINÇOTTE nv Jan Olieslagerslaan 35, 1800 Vilvoorde, Belgium This is to certify that Avient Located at Rue Melville Wilson 2 5330 Assesse Belgium has established and maintains an energy management system according the requirements of EN ISO 50001 : 2018 “Energy Management System” for: Design and manufacture of colour and additive concentrates, thermoplastic resins and speciality compounds This certificate is based on the result of an energy audit documented in the audit report 61231731. Certificate number: 24 EN 47 Valid from 1 February 2024 to 31 January 2027 Further clarifications regarding the scope of this certificate and the applicability of EN ISO 50001 : 2018 requirements may be obtained by consulting the organization.

TEMPERATURE Material Rear Center Front Nozzle Melt Mold Nylon 6,6 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) Nylon 6,6 30% SS 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) PBT 510–410 (265–280) 490–540 (255–280) 480–530 480–530 480–530 150–250 (65–120) PC 14% NiCF 540–570 540–570 530–560 530–560 530–560 150–250 (65–120) ABS 470–520 460–520 460–520 460–530 (240–275) 460–530 (240–275) 100–200 (40–90) PP 440–480 (225–250) 440–480 (225–250) 430–470 (220–245) 420–460 (215–240) 420–460 (215–240) 125–175 (50–80) DRYING Material Temperature °F (°C) Time Minimum Moisture Maximum Moisture Nylon 6,6 14% NiCF 180 (80) 4–5 hours 0.05% 0.20% Nylon 6,6 30% SS 180 (80) 4–5 hours 0.05% 0.20% PBT 14% NiCF 250 (120) 6-8 hours 0.02% 0.03% PC 14% NiCF 250 (120) 3–4 hours 0.02% 0.02% ABS 14% NiCF 200 (90) 2–4 hours 0.05% 0.10% PP 14% NiCF 180 (80) 2–4 hours 0.20% 0.30% Equipment • Feed throats smaller than 2.5" may cause bridging due to pellet size - Larger feed throats will be more advantageous with long fiber EMI shielding resins • General purpose metering screw is recommended - Mixing/barrier screws are not recommended • L/D ratio - 18:1–20:1 (40% feed, 40% transition, 20% metering) • Low compression ratio - 2:1–3:1 • Deep flights recommended - Metering zone 3.5 mm - Feed zone 7.5 mm • Check ring - Three-piece, free-flowing check ring • General purpose nozzle (large nozzle tips are recommended) - Minimum orifice diameter of 7/32" - Tapered nozzles are not recommended for long fiber EMI shielding resins • Clamp tonnage: - 2.5–5 tons/in2 Gates • Large, free-flow gating recommended - 0.25" x 0.125" land length - 0.5" gate depth Runners • Full round gate design • No sharp corners • Minimum of 0.25" diameter • Hot runners can be used PROCESSING Screw Speed Slower screw speeds are recommended to protect fiber length Back Pressure Lower back pressure is recommended to protect fiber length Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) PROCESS CONSIDERATIONS Recommended – retain fiber length (maximize conductivity) • Low shear process • Low screw speed and screw RPM • Slow Injection speed • Fill to 99–100% on first stage of injection - Reduces potential nesting of fibers at gate location - Improves mechanical performance near gate location - Promotes ideal fiber orientation Resin Rich Surface • Achieved when using a hot mold temperature and longer cure times ≥ Max mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could reduce attenuation performance in an assembly Fiber Rich Surface • Achieved when using a cold mold temperature and shorter cure times ≤ Minimum mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could improve attenuation performance in an assembly www.avient.com Copyright © 2020, Avient Corporation. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

WHEN YOU WORK WITH Avient From concept to component, you can leverage Avient’s expertise throughout the development cycle in three key areas: Materials, Processing & Design DE SI GN MATERIALS www.avient.com Copyright © 2020, Avient Corporation. Values reported as “typical” or stated without a range do not state minimum or maximum properties; consult your sales representative for property ranges and min/max specifications.

January 31, 2023

January 11, 2022

January 23, 2017

January 8, 2024

January 6, 2023

January 14, 2025

January 23, 2017